Network Working Group M. Boucadair, Ed. Internet-Draft D. Binet Intended status: Informational S. Durel Expires: October 13, 2014 B. Chatras France Telecom T. Reddy Cisco B. Williams Akamai, Inc. B. Sarikaya L. Xue Huawei April 11, 2014 Host Identification: Use Cases draft-boucadair-intarea-host-identifier-scenarios-05 Abstract This document describes a set of scenarios in which host identification is problematic. The document does not include any solution-specific discussion. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 13, 2014. Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents Boucadair, et al. Expires October 13, 2014 [Page 1] Internet-Draft Host ID Use Cases April 2014 (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Use Case 1: CGN . . . . . . . . . . . . . . . . . . . . . . . 4 4. Use Case 2: A+P . . . . . . . . . . . . . . . . . . . . . . . 4 5. Use Case 3: Application Proxies . . . . . . . . . . . . . . . 5 6. Use Case 4: Open Wi-Fi or Provider Wi-Fi . . . . . . . . . . 6 7. Use Case 5: Policy and Charging Control Architecture . . . . 7 8. Use Case 6: Cellular Networks . . . . . . . . . . . . . . . . 8 9. Use Case 7: Femtocells . . . . . . . . . . . . . . . . . . . 9 10. Use Case 8: Overlay Network . . . . . . . . . . . . . . . . . 10 11. Use Case 9: Emergency Calls . . . . . . . . . . . . . . . . . 12 12. Use Case 10: Traffic Detection Function . . . . . . . . . . . 13 13. Use Case 11: Fixed and Mobile Network Convergence . . . . . . 14 14. Synthesis . . . . . . . . . . . . . . . . . . . . . . . . . . 17 15. Privacy Considerations . . . . . . . . . . . . . . . . . . . 17 16. Security Considerations . . . . . . . . . . . . . . . . . . . 17 17. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18 18. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 18 19. Informative References . . . . . . . . . . . . . . . . . . . 18 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 20 1. Introduction The goal of this document is to enumerate use cases which encounter the issue of uniquely identifying a host among those sharing the same IP address. Examples of encountered issues in those use cases are: o Blacklist a misbehaving host without impacting all hosts sharing the same IP address. o Enforce a per-subscriber/per-UE policy (e.g., limit access to the service based on some counters such as volume-based service offering); enforcing the policy will have impact on all hosts sharing the same IP address. o If invoking a service has failed (e.g., wrong login/password), all hosts sharing the same IP address may not be able to access that service. o Need to correlate between the internal address:port and external address:port to generate and therefore to enforce policies. Boucadair, et al. Expires October 13, 2014 [Page 2] Internet-Draft Host ID Use Cases April 2014 o Query a location server for the location of an emergency caller based on the source IP address. It is out of scope of this document to list all the encountered issues as this is already covered in [RFC6269]. The following use cases are identified: (1) Carrier Grade NAT (CGN) (Section 3) (2) A+P (e.g., MAP ) (Section 4) (3) Application Proxies (Section 5) (4) Provider Wi-Fi (Section 6) (5) Policy and Charging Architectures (Section 7) (6) Cellular Networks (Section 8) (7) Femtocells (Section 9) (8) Overlay Networks (e.g., CDNs) (Section 10) (9) Emergency Calls (Section 11) (10) Traffic Detection Function (Section 12) (11) Fixed and Mobile Network Convergence (Section 13) The analysis of the use cases listed in this document indicates several root causes for the host identification issue: 1. Presence of address sharing (NAT, A+P, application proxies, etc.). 2. Use of tunnels between two administrative domains. 3. Combination of address sharing and presence of tunnels in the path. 2. Scope It is out of scope of this document to argue in favor or against the use cases listed in the following sections. The goal is to identify scenarios the authors are aware of and which share the same issue of host identification. This document does not include any solution-specific discussion. This document can be used as a tool to design solution(s) mitigating the encountered issues. Describing the use case allows to identify what is common between the use cases and then would help during the solution design phase. The document does not elaborate whether explicit authentication is enabled or not. Boucadair, et al. Expires October 13, 2014 [Page 3] Internet-Draft Host ID Use Cases April 2014 3. Use Case 1: CGN Several flavors of stateful CGN have been defined. A non-exhaustive list is provided below: 1. NAT44 ([RFC6888], [I-D.tsou-stateless-nat44]) 2. DS-Lite NAT44 [RFC6333] 3. NAT64 [RFC6146] 4. NPTv6 [RFC6296] As discussed in [RFC6967], remote servers are not able to distinguish between hosts sharing the same IP address (Figure 1). +-----------+ | HOST_1 |----+ +-----------+ | +--------------------+ +------------+ | | |------| server 1 | +-----------+ +-----+ | | +------------+ | HOST_2 |--| CGN |----| INTERNET | :: +-----------+ +-----+ | | +------------+ | | |------| server n | +-----------+ | +--------------------+ +------------+ | HOST_3 |-----+ +-----------+ Figure 1: CGN Reference Architecture Some of the above referenced CGN use cases will be satisfied by eventual completion of the transition to IPv6 across the Internet (e.g., NAT64), but this is not true of all CGN use cases (e.g. NPTv6 [RFC6296]) for which some of the issues discussed in [RFC6269] will be encountered (e.g., impact on geolocation [RFC6269]). Note, it is not the intent of this document to advocate in favor or against NPTv6, but to highlight the complications that may raise when enabling such function. 4. Use Case 2: A+P A+P [RFC6346][I-D.ietf-softwire-map][I-D.ietf-softwire-lw4over6] denotes a flavor of address sharing solutions which does not require any additional NAT function be enabled in the service provider's network. A+P assumes subscribers are assigned with the same IPv4 address together with a port set. Subscribers assigned with the same IPv4 address should be assigned non overlapping port sets. Devices Boucadair, et al. Expires October 13, 2014 [Page 4] Internet-Draft Host ID Use Cases April 2014 connected to an A+P-enabled network should be able to restrict the IPv4 source port to be within a configured range of ports. To forward incoming packets to the appropriate host, a dedicated entity called PRR (Port Range Router, [RFC6346]) is needed (Figure 2). Similar to the CGN case, the same issue to identify hosts sharing the same IP address is encountered by remote servers. +-----------+ | HOST_1 |----+ +-----------+ | +--------------------+ +------------+ | | |------| server 1 | +-----------+ +-----+ | | +------------+ | HOST_2 |--| PRR |----| INTERNET | :: +-----------+ +-----+ | | +------------+ | | |------| server n | +-----------+ | +--------------------+ +------------+ | HOST_3 |-----+ +-----------+ Figure 2: A+P Reference Architecture 5. Use Case 3: Application Proxies This scenario is similar to the CGN scenario. Remote servers are not able to distinguish hosts located behind the PROXY. Applying policies on the perceived external IP address as received from the PROXY will impact all hosts connected to that PROXY. Figure 3 illustrates a simple configuration involving a proxy. Note several (per-application) proxies may be deployed. +-----------+ | HOST_1 |----+ +-----------+ | +--------------------+ +------------+ | | |------| server 1 | +-----------+ +-----+ | | +------------+ | HOST_2 |--|PROXY|----| INTERNET | :: +-----------+ +-----+ | | +------------+ | | |------| server n | +-----------+ | +--------------------+ +------------+ | HOST_3 |-----+ +-----------+ Figure 3: Proxy Reference Architecture Boucadair, et al. Expires October 13, 2014 [Page 5] Internet-Draft Host ID Use Cases April 2014 In the application proxy scenario, packets/connections must be received by the proxy regardless of the IP address family in use. The requirements of this use case are not satisfied by eventual completion of the transition to IPv6 across the Internet. 6. Use Case 4: Open Wi-Fi or Provider Wi-Fi In the context of Provider Wi-Fi (WLAN), a dedicated SSID can be configured and advertised by the RG (Residential Gateway) for visiting terminals. These visiting terminals can be mobile terminals, PCs, etc. Several deployment scenarios are envisaged: 1. Deploy a dedicated node in the service provider's network which will be responsible to intercept all the traffic issued from visiting terminals (see Figure 4). This node may be co-located with a CGN function if private IPv4 addresses are assigned to visiting terminals. Similar to the CGN case discussed in Section 3, remote servers may not be able to distinguish visiting hosts sharing the same IP address (see [RFC6269]). 2. Unlike the previous deployment scenario, IPv4 addresses are managed by the RG without requiring any additional NAT to be deployed in the service provider's network for handling traffic issued from visiting terminals. Concretely, a visiting terminal is assigned with a private IPv4 address from the IPv4 address pool managed by the RG. Packets issued form a visiting terminal are translated using the public IP address assigned to the RG (see Figure 5). This deployment scenario induces the following identification concerns: * The provider is not able to distinguish the traffic belonging to the visiting terminal from the traffic of the subscriber owning the RG. This is needed to apply some policies such as: accounting, DSCP remarking, black list, etc. * Similar to the CGN case Section 3, a misbehaving visiting terminal is likely to have some impact on the experienced service by the subscriber owning the RG (e.g., some of the issues are discussed in [RFC6269]). Boucadair, et al. Expires October 13, 2014 [Page 6] Internet-Draft Host ID Use Cases April 2014 +-------------+ |Local_HOST_1 |----+ +-------------+ | | | +-------------+ +-----+ | +-----------+ |Local_HOST_2 |--| RG |-|--|Border Node| +-------------+ +-----+ | +----NAT----+ | | +-------------+ | | Service Provider |Visiting Host|-----+ +-------------+ Figure 4: NAT enforced in a Service Provider's Node +-------------+ |Local_HOST_1 |----+ +-------------+ | | | +-------------+ +-----+ | +-----------+ |Local_HOST_2 |--| RG |-|--|Border Node| +-------------+ +-NAT-+ | +-----------+ | | +-------------+ | | Service Provider |Visiting Host|-----+ +-------------+ Figure 5: NAT located in the RG 7. Use Case 5: Policy and Charging Control Architecture This issue is related to the framework defined in [TS23.203] when a NAT is located between the PCEF (Policy and Charging Enforcement Function) and the AF (Application Function) as shown in Figure 6. The main issue is: PCEF, PCRF and AF all receive information bound to the same UE( User Equipment) but without being able to correlate between the piece of data visible for each entity. Concretely, o PCEF is aware of the IMSI (International Mobile Subscriber Identity) and an internal IP address assigned to the UE. o AF receives an external IP address and port as assigned by the NAT function. Boucadair, et al. Expires October 13, 2014 [Page 7] Internet-Draft Host ID Use Cases April 2014 o PCRF is not able to correlate between the external IP address/port assigned by the NAT (received from the AF) and the internal IP address and IMSI of the UE (received from the PCEF). +------+ | PCRF |-----------------+ +------+ | | | +----+ +------+ +-----+ +-----+ | UE |------| PCEF |---| NAT |----| AF | +----+ +------+ +-----+ +-----+ Figure 6: NAT located between AF and PCEF This scenario can be generalized as follows (Figure 7): o Policy Enforcement Point (PEP, [RFC2753]) o Policy Decision Point (PDP, [RFC2753]) +------+ | PDP |-----------------+ +------+ | | | +----+ +------+ +-----+ +------+ | UE |------| PEP |---| NAT |----|Server| +----+ +------+ +-----+ +------+ Figure 7: NAT located between PEP and Server Note that an issue is encountered to enforce per-UE policies when the NAT is located before the PEP function (see Figure 8): +------+ | PDP |------+ +------+ | | | +----+ +------+ +-----+ +------+ | UE |------| NAT |---| PEP |----|Server| +----+ +------+ +-----+ +------+ Figure 8: NAT located before PEP 8. Use Case 6: Cellular Networks Cellular operators allocate private IPv4 addresses to mobile terminals and deploy NAT44 function, generally co-located with firewalls, to access to public IP services. The NAT function is Boucadair, et al. Expires October 13, 2014 [Page 8] Internet-Draft Host ID Use Cases April 2014 located at the boundaries of the PLMN (Public Land Mobile Network). IPv6-only strategy, consisting in allocating IPv6 prefixes only to mobile terminals, is considered by various operators. A NAT64 function is also considered in order to preserve IPv4 service continuity for these customers. These NAT44 and NAT64 functions bring some issues very similar to those mentioned in Figure 1 and Section 7. This issue is particularly encountered if policies are to be applied on the Gi interface: a private IP address is assigned to the mobile terminals, there is no correlation between the internal IP address and the external address:port assigned by the NAT function, etc. 9. Use Case 7: Femtocells This use case can be seen as a combination of the use cases described in Section 6 and Section 7. The reference architecture is shown in Figure 8. +---------------------------+ | +----+ +--------+ +----+ | +-----------+ +-------------------+ | | UE | | Stand- |<=|====|=|===|===========|==|=>+--+ +--+ | | +----+ | alone | | RG | | | | | | | | | Mobile | | | FAP | +----+ | | | | |S | |F | Network| | +--------+ (NAPT) | | Broadband | | |e | |A | | +---------------------------+ | Fixed | | |G |-|P | +-----+| | Network | | |W | |G |-| Core|| +---------------------------+ | (BBF) | | | | |W | | Ntwk|| | +----+ +------------+ | | | | | | | | +-----+| | | UE | | Integrated |<====|===|===========|==|=>+--+ +--+ | | +----+ | FAP (NAPT) | | +-----------+ +-------------------+ | +------------+ | +---------------------------+ <=====> IPsec tunnel CoreNtwk Core Network FAPGW FAP Gateway SeGW Security Gateway Figure 9: Femtocell Reference Architecture UE is connected to the FAP at the residential gateway (RG), routed back to 3GPP Evolved Packet Core (EPC). UE is assigned IPv4 address by the Mobile Network. Mobile operator's FAP leverages the IPsec IKEv2 to interconnect FAP with the SeGW over the BBF network. Both the FAP and the SeGW are managed by the mobile operator which may be a different operator for the BBF network. Boucadair, et al. Expires October 13, 2014 [Page 9] Internet-Draft Host ID Use Cases April 2014 An investigated scenario is the mobile operator to pass on its mobile subscriber's policies to the BBF to support traffic policy control . But most of today's broadband fixed networks are relying on the private IPv4 addressing plan (+NAPT) to support its attached devices including the mobile operator's FAP. In this scenario, the mobile network needs to: o determine the FAP's public IPv4 address to identify the location of the FAP to ensure its legitimacy to operate on the license spectrum for a given mobile operator prior to the FAP be ready to serve its mobile devices. o determine the FAP's pubic IPv4 address together with the translated port number of the UDP header of the encapsulated IPsec tunnel for identifying the UE's traffic at the fixed broadband network. o determine the corresponding FAP's public IPv4 address associated with the UE's inner-IPv4 address which is assigned by the mobile network to identify the mobile UE to allow the PCRF to retrieve the special UE's policy (e.g., QoS) to be passed onto the Broadband Policy Control Function (BPCF) at the BBF network. SeGW would have the complete knowledge of such mapping, but the reasons for unable to use SeGW for this purpose is explained in "Problem Statements" (section 2 of [I-D.so-ipsecme-ikev2-cpext]). This use case involves PCRF/BPCF but it is valid in other deployment scenarios making use of AAA servers. The issue of correlating the internal IP address and the public IP address is valid even if there is no NAT in the path. 10. Use Case 8: Overlay Network An overlay network is a network of machines distributed throughout multiple autonomous systems within the public Internet that can be used to improve the performance of data transport (see Figure 10). IP packets from the sender are delivered first to one of the machines that make up the overlay network. That machine then relays the IP packets to the receiver via one or more machines in the overlay network, applying various performance enhancement methods. Boucadair, et al. Expires October 13, 2014 [Page 10] Internet-Draft Host ID Use Cases April 2014 +------------------------------------+ | | | INTERNET | | | +-----------+ | +------------+ | | HOST_1 |-----| OVRLY_IN_1 |-----------+ | +-----------+ | +------------+ | | | | | +-----------+ | +------------+ +-----------+ | +--------+ | HOST_2 |-----| OVRLY_IN_2 |-----| OVRLY_OUT |-----| SERVER | +-----------+ | +------------+ +-----------+ | +--------+ | | | +-----------+ | +------------+ | | | HOST_3 |-----| OVRLY_IN_3 |-----------+ | +-----------+ | +------------+ | | | +------------------------------------+ Figure 10: Overlay Network Reference Architecture Such overlay networks are used to improve the performance of content delivery [IEEE1344002]. Overlay networks are also used for peer-to- peer data transport [RFC5694], and they have been suggested for use in both improved scalability for the Internet routing infrastructure [RFC6179] and provisioning of security services (intrusion detection, anti-virus software, etc.) over the public Internet [IEEE101109]. In order for an overlay network to intercept packets and/or connections transparently via base Internet connectivity infrastructure, the overlay ingress and egress hosts (OVERLAY_IN and OVERLAY_OUT) must be reliably in-path in both directions between the connection-initiating HOST and the SERVER. When this is not the case, packets may be routed around the overlay and sent directly to the receiving host. For public overlay networks, where the ingress and/or egress hosts are on the public Internet, packet interception commonly uses network address translation for the source (SNAT) or destination (DNAT) addresses in such a way that the public IP addresses of the true endpoint hosts involved in the data transport are invisible to each other (see Figure 11). For example, the actual sender and receiver may use two completely different pairs of source and destination addresses to identify the connection on the sending and receiving networks in cases where both the ingress and egress hosts are on the public Internet. Boucadair, et al. Expires October 13, 2014 [Page 11] Internet-Draft Host ID Use Cases April 2014 ip hdr contains: ip hdr contains: SENDER -> src = sender --> OVERLAY --> src = overlay2 --> RECEIVER dst = overlay1 dst = receiver Figure 11: NAT operations in an Overlay Network In this scenario, the remote server is not able to distinguish among hosts using the overlay for transport. In addition, the remote server is not able to determine the overlay ingress point being used by the host, which can be useful for diagnosing host connectivity issues. In some of the above referenced use cases, IP packets traverse the overlay network fundamentally unchanged, with the overlay network functioning much like a CGN (Section 3). In other cases, connection- oriented data flows (e.g. TCP) are terminated by the overlay in order to perform object caching and other such transport and application layer optimizations, similar to the proxy scenario (Section 5). In both cases, address sharing is a requirement for packet/connection interception, which means that the requirements for this use case are not satisfied by the eventual completion of the transition to IPv6 across the Internet. More details about this use case are provided in [I-D.williams-overlaypath-ip-tcp-rfc]. 11. Use Case 9: Emergency Calls Voice service providers (VSPs) operating under certain jurisdictions are required to route emergency calls from their subscribers and have to include information about the caller's location in signaling messages they send towards PSAPs (Public Safety Answering Points, [RFC6443]), via an Emergency Service Routing Proxy (ESRP, [RFC6443]). This information is used both for the determination of the correct PSAP and to reveal the caller's location to the selected PSAP. In many countries, regulation bodies require that this information be provided by the network rather than the user equipment, in which case the VSP needs to retrieve this information (by reference or by value) from the access network where the caller is attached. This requires the VSP call server receiving an emergency call request to identify the relevant access network and to query a Location Information Server (LIS) in this network using a suitable look-up key. In the simplest case, the source IP address of the IP packet carrying the call request is used both for identifying the access network (thanks to a reverse DNS query) and as a look-up key to query Boucadair, et al. Expires October 13, 2014 [Page 12] Internet-Draft Host ID Use Cases April 2014 the LIS. Obviously the user-id as known by the VSP (e.g., telephone number, or email-formatted URI) can't be used as it is not known by the access network. The above mechanism is broken when there is a NAT between the user and the VSP and/or if the emergency call is established over a VPN tunnel (e.g., an employee remotely connected to a company VoIP server through a tunnel wishes to make an emergency call). In such cases, the source IP address received by the VSP call server will identity the NAT or the address assigned to the caller equipment by the VSP (i.e., the address inside the tunnel). This is similar to the CGN case (Section 3) and overlay network case (Section 10) and applies irrespective of the IP versions used on both sides of the NAT and/or inside and outside the tunnel. Therefore, the VSP needs to receive an additional piece of information that can be used to both identify the access network where the caller is attached and query the LIS for his/her location. This would require the NAT or the Tunnel Endpoint to insert this extra information in the call requests delivered to the VSP call servers. For example, this extra information could be a combination of the local IP address assigned by the access network to the caller's equipment with some form of identification of this access network. However, because it shall be possible to setup an emergency call regardless of the actual call control protocol used between the user and the VSP (e.g., SIP [RFC3261], IAX [RFC5456], tunneled over HTTP, or proprietary protocol, possibly encrypted), this extra information has to be conveyed outside the call request, in the header of lower layers protocols. 12. Use Case 10: Traffic Detection Function Operators expect that the traffic subject to the packet inspection is routed via the Traffic Detection Function (TDF) function as requirement specified in [TS29.212], otherwise, the traffic may bypass the TDF. This assumption only holds if it is possible to identify individual UEs behind NA(P)T which may be deployed into the RG in fixed broadband network, shown in Figure 12. As a result, additional mechanisms are needed to enable this requirement. Boucadair, et al. Expires October 13, 2014 [Page 13] Internet-Draft Host ID Use Cases April 2014 +--------+ | | +-------+ PCRF | | | | | +--------+ +--------+ +--------+ +--------+ +----+----+ | | | | | +-----+ | | ------------------------------------------------------------------ | | | | | | | TDF | / \ | ****************************************************************** | | | +-------+ | | | Service | | | | | | | \ / | | | | | | | +--------+ | | | | | | +--------+ PDN | | ********---------**********--------************------------******* | | UE | | RG | | BNG +------------------+ Gateway| +--------+ +--------+ +--------+ +--------+ Legends: --------- 3GPP UE User Plane Traffic Offloaded subject to packet inspection ********* 3GPP UE User Plane Traffic Offloaded not subject to packet inspection *****---- 3GPP UE User Plane Traffic Home Routed Figure 12: UE's Traffic Routed with TDF 13. Use Case 11: Fixed and Mobile Network Convergence In the Policy for Convergence of Fixed Mobile Convergence (FMC) scenario, the fixed broadband network must partner with the mobile network to acquire the policies for the terminals or hosts attaching to the fixed broadband network, shown in Figure 13 so that host- specific QoS and accounting policies can be applied. A UE is connected to the RG, routed back to the mobile network. The mobile operator's PCRF needs to maintain the interconnect with the Broadband Policy Control Function (BPCF) in the BBF network for PCC (Section 7). The hosts (i.e., UEs) attaching to fixed broadband network with a NA(P)T deployed should be identified. Based on the UE identification, the BPCF to deploy policy rules in the fixed broadband network can acquire the associated policy rules of the identified UE from the PCRF in the mobile network. But in the fixed broadband network, private IPv4 address is supported. The similar requirements are raised in this use case as Section 9. Boucadair, et al. Expires October 13, 2014 [Page 14] Internet-Draft Host ID Use Cases April 2014 +------------------------------+ +-------------+ | | | | | +------+ | | +------+ | | | BPCF +---+---+-+ PCRF | | | +--+---+ | | +---+--+ | +-------+ | | | | | | |HOST_1 |Private IP1 +--+---+ | | +---+--+ | +-------+ | +----+ | | | | | | | | | RG | | | | | | | | | |with+-------------+ BNG +--------+ PGW | | +-------+ | | NAT| | | | | | | | |HOST_2 | | +----+ | | | | | | | +-------+Private IP2 +------+ | | +------+ | | | | | | | | | | Fixed | | Mobile | | Broadband | | Network | | Network | | | | | | | +------------------------------+ +-------------+ Figure 13: Reference Architecture for Policy for Convergence in Fixed and Mobile Network Convergence (1) In IPv6 network, the similar issues exists when the IPv6 prefix is sharing between multiple UEs attaching to the RG (see Figure 14). The case applies when RG is assigned a single prefix, the home network prefix, e.g. using DHCPv6 Prefix Delegation [RFC3633] with the edge router, BNG acting as the Delegating Router (DR). RG uses the home network prefix in the address configuration using stateful (DHCPv6) or stateless address assignment (SLAAC) techniques. Boucadair, et al. Expires October 13, 2014 [Page 15] Internet-Draft Host ID Use Cases April 2014 +------------------------------+ +-------------+ | | | | | | | +------+ | | +-------------+ PCRF | | | | | | +---+--+ | +-------+ | | | | | | |HOST_1 |--+ +--+---+ | | +---+--+ | +-------+ | +----+ | | | | | | | | | RG | | | | | | | | | | +------------+ BNG +---------+ PGW | | +-------+ | | | | | | | | | | |HOST_2 |--+ +----+ | | | | | | | +-------+ | +------+ | | +------+ | | | | | | | | | | Fixed | | Mobile | | Broadband | | Network | | Network | | | | | | | +------------------------------+ +-------------+ Figure 14: Reference Architecture for Policy for Convergence in Fixed and Mobile Network Convergence (2) BNG acting as PCEF initiates an IP Connectivity Access Network (IP- CAN) session with the policy server, a.k.a. Policy and Charging Rules Function (PCRF), to receive the Quality of Service (QoS) parameters and Charging rules. BNG provides to the PCRF the IPv6 Prefix assigned to the host, in this case the home network prefix and an ID which in this case has to be equal to the RG specific home network line ID. HOST_1 in Figure 14 creates an 128-bit IPv6 address using this prefix and adding its interface id. Having completed the address configuration, the host can start communication with a remote hosts over Internet. However, no specific IP-CAN session can be assigned to HOST_1, and consequently the QoS and accounting performed will be based on RG subscription. Another host, e.g. HOST_2, attaches to RG and also establishes an IPv6 address using the home network prefix. Edge router, the BNG, is not involved with this and all other such address assignments. This leads to the case where no specific IP-CAN session/sub-session can be assigned to the hosts, HOST_1, HOST_2, etc., and consequently the QoS and accounting performed can only be based on RG subscription and not host specific. Therefore IPv6 prefix sharing in Policy for Boucadair, et al. Expires October 13, 2014 [Page 16] Internet-Draft Host ID Use Cases April 2014 Convergence scenario leads to similar issues as the address sharing as it has been explained in the previous use cases in this document. 14. Synthesis The following table shows whether each use case is valid for IPv4/ IPv6 and if it is within one single administrative domain or span multiple domains. +-------------------+------+-------------+-----------------------+ | Use Case | IPv4 | IPv6 | Single Administrative | | | |------+------| Domain | | | |Client|Server| | +-------------------+------+------+------+-----------------------+ | CGN | Yes |Yes(1)| No | No | | A+P | Yes | No | No | No | | Application Proxy | Yes |Yes(2)|Yes(2)| No | | Provider Wi-Fi | Yes | No | No | Yes | | PCC | Yes |Yes(1)| No | Yes | | Femtocells | Yes | No | No | No | | Cellular Networks | Yes |Yes(1)| No | Yes | | Overlay Networks | Yes |Yes(3)|Yes(3)| No | | Emergency Calls | Yes | Yes |Yes | No | | TDF | Yes | Yes | No | Yes | | FMC | Yes |Yes(1)| No | No | +-------------------+------+------+------------------------------+ Notes: (1) e.g., NAT64 (2) A proxy can use IPv6 for the communication leg with the server or the application client. (3) This use case is a combination of CGN and Application Proxies. 15. Privacy Considerations Privacy-related considerations that apply to means to reveal a host identified are discussed in [RFC6967]. This document does not introduce additional privacy issues than those discussed in [RFC6967]. 16. Security Considerations This document does not define an architecture nor a protocol; as such it does not raise any security concern. Host identifier related security considerations are discussed in [RFC6967]. Boucadair, et al. Expires October 13, 2014 [Page 17] Internet-Draft Host ID Use Cases April 2014 17. IANA Considerations This document does not require any action from IANA. 18. Acknowledgments Many thanks to F. Klamm, D. Wing, and D. von Hugo for their review. Figure 8 and part of the text in Section 9 are inspired from [I-D.so-ipsecme-ikev2-cpext]. 19. Informative References [I-D.ietf-softwire-lw4over6] Cui, Y., Qiong, Q., Boucadair, M., Tsou, T., Lee, Y., and I. Farrer, "Lightweight 4over6: An Extension to the DS- Lite Architecture", draft-ietf-softwire-lw4over6-08 (work in progress), March 2014. [I-D.ietf-softwire-map] Troan, O., Dec, W., Li, X., Bao, C., Matsushima, S., Murakami, T., and T. Taylor, "Mapping of Address and Port with Encapsulation (MAP)", draft-ietf-softwire-map-10 (work in progress), January 2014. [I-D.so-ipsecme-ikev2-cpext] So, T., "IKEv2 Configuration Payload Extension for Private IPv4 Support for Fixed Mobile Convergence", draft-so- ipsecme-ikev2-cpext-02 (work in progress), June 2012. [I-D.tsou-stateless-nat44] Tsou, T., Liu, W., Perreault, S., Penno, R., and M. Chen, "Stateless IPv4 Network Address Translation", draft-tsou- stateless-nat44-02 (work in progress), October 2012. [I-D.williams-overlaypath-ip-tcp-rfc] Williams, B., "Overlay Path Option for IP and TCP", draft- williams-overlaypath-ip-tcp-rfc-04 (work in progress), June 2013. [IEEE101109] Salah, K., Calero, J., Zeadally, S., Almulla, S., and M. ZAaabi, "Using Cloud Computing to Implement a Security Overlay Network, IEEE Security & Privacy, 21 June 2012. IEEE Computer Society Digital Library.", June 2012. Boucadair, et al. Expires October 13, 2014 [Page 18] Internet-Draft Host ID Use Cases April 2014 [IEEE1344002] Byers, J., Considine, J., Mitzenmacher, M., and S. Rost, "Informed content delivery across adaptive overlay networks: IEEE/ACM Transactions on Networking, Vol 12, Issue 5, ppg 767-780", October 2004. [RFC2753] Yavatkar, R., Pendarakis, D., and R. Guerin, "A Framework for Policy-based Admission Control", RFC 2753, January 2000. [RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, June 2002. [RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6", RFC 3633, December 2003. [RFC5456] Spencer, M., Capouch, B., Guy, E., Miller, F., and K. Shumard, "IAX: Inter-Asterisk eXchange Version 2", RFC 5456, February 2010. [RFC5694] Camarillo, G. and IAB, "Peer-to-Peer (P2P) Architecture: Definition, Taxonomies, Examples, and Applicability", RFC 5694, November 2009. [RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", RFC 6146, April 2011. [RFC6179] Templin, F., "The Internet Routing Overlay Network (IRON)", RFC 6179, March 2011. [RFC6269] Ford, M., Boucadair, M., Durand, A., Levis, P., and P. Roberts, "Issues with IP Address Sharing", RFC 6269, June 2011. [RFC6296] Wasserman, M. and F. Baker, "IPv6-to-IPv6 Network Prefix Translation", RFC 6296, June 2011. [RFC6333] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual- Stack Lite Broadband Deployments Following IPv4 Exhaustion", RFC 6333, August 2011. [RFC6346] Bush, R., "The Address plus Port (A+P) Approach to the IPv4 Address Shortage", RFC 6346, August 2011. Boucadair, et al. Expires October 13, 2014 [Page 19] Internet-Draft Host ID Use Cases April 2014 [RFC6443] Rosen, B., Schulzrinne, H., Polk, J., and A. Newton, "Framework for Emergency Calling Using Internet Multimedia", RFC 6443, December 2011. [RFC6888] Perreault, S., Yamagata, I., Miyakawa, S., Nakagawa, A., and H. Ashida, "Common Requirements for Carrier-Grade NATs (CGNs)", BCP 127, RFC 6888, April 2013. [RFC6967] Boucadair, M., Touch, J., Levis, P., and R. Penno, "Analysis of Potential Solutions for Revealing a Host Identifier (HOST_ID) in Shared Address Deployments", RFC 6967, June 2013. [TS23.203] 3GPP, , "Policy and charging control architecture", September 2012. [TS29.212] 3GPP, , "Policy and Charging Control (PCC); Reference Points", December 2013. Authors' Addresses Mohamed Boucadair (editor) France Telecom Rennes 35000 France Email: mohamed.boucadair@orange.com David Binet France Telecom Rennes France Email: david.binet@orange.com Sophie Durel France Telecom Rennes France Email: sophie.durel@orange.com Boucadair, et al. Expires October 13, 2014 [Page 20] Internet-Draft Host ID Use Cases April 2014 Bruno Chatras France Telecom Paris France Email: bruno.chatras@orange.com Tirumaleswar Reddy Cisco Systems, Inc. Cessna Business Park, Varthur Hobli Sarjapur Marathalli Outer Ring Road Bangalore, Karnataka 560103 India Email: tireddy@cisco.com Brandon Williams Akamai, Inc. Cambridge MA USA Email: brandon.williams@akamai.com Behcet Sarikaya Huawei 5340 Legacy Dr. Building 3, Plano, TX 75024 USA Email: behcet.sarikaya@huawei.com Li Xue Huawei Beijing China Email: xueli@huawei.com Boucadair, et al. Expires October 13, 2014 [Page 21]