Transmission of SCHC-compressed packets over IEEE 802.15.4 networks

RFC 6282 is the main specification for IPv6 over Low power Wireless Personal Area Network (6LoWPAN) IPv6 header compression . This RFC was designed assuming IEEE 802.15.4 as the layer below the 6LoWPAN adaptation layer, and it has also been reused (with proper adaptations) for IPv6 header compression over many other technologies relatively similar to IEEE 802.15.4 in terms of characteristics such as physical layer bit rate, layer 2 maximum payload size, etc. Examples of such technologies comprise BLE, DECT-ULE, ITU G.9959, MS/TP, NFC, and PLC. RFC 6282 provides additional functionality, such as a mechanism for UDP header compression. In the best cases, RFC 6282 allows to compress a 40-byte IPv6 header down to a 2-byte compressed header (for link-local interactions) or a 3-byte compressed header (when global IPv6 addresses are used). On the other hand, an RFC 6282 compressed UDP header has a typical size of 4 bytes. Therefore, in advantageous conditions, a 48-byte uncompressed IPv6/UDP header may be compressed down to a 6-byte format (when using link-local addresses) or a 7-byte format (for global interactions) by using RFC 6282. Recently, a framework called Static Context Header Compression (SCHC) has been designed with the primary goal of supporting IPv6 over Low Power Wide Area Network (LPWAN) technologies . SCHC comprises header compression and fragmentation functionality tailored to the extraordinary constraints of LPWAN technologies, which are more severe than those exhibited by IEEE 802.15.4 or other relatively similar technologies. SCHC header compression allows a greater compression ratio than that of RFC 6282. If used properly, SCHC allows to compress an IPv6/UDP header down to e.g. a single byte. In addition, SCHC can be used to compress Constrained Application Protocol (CoAP) headers as well , which further increases the achievable performance improvement of using SCHC header compression, since there is no 6LoWPAN header compression defined for CoAP. Therefore, it may make sense to use SCHC header compression in some 6LoWPAN environments [I-D.toutain-6lo-6lo-and-schc], including IEEE 802.15.4 networks, considering its greater efficiency. If SCHC header compression is added to the panoply of header compression mechanisms used in 6LoWPAN environments, then there is a need to signal when a packet header has been compressed by using SCHC. To this end, in its current form, the present document specifies a 6LoWPAN Dispatch Type for SCHC header compression, based on exploiting RFC 8025 Dispatch type space . This document specifies how a SCHC-compressed packet can be carried over IEEE 802.15.4 networks. Note that, as per this document, and while SCHC defines fragmentation mechanisms as well, 6LoWPAN/6Lo fragmentation is used when necessary to transport SCHC-compressed packets over IEEE 802.15.4 networks . TO-DO: indicate here any specific updates of RFC 8724 for IEEE 802.15.4.

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP14 , , when, and only when, they appear in all capitals, as shown here.

The reader is expected to be familiar with the terms and concepts defined in the specification of SCHC (RFC 8724).

IEEE 802.15.4 supports two main network topologies: the star topology, and the peer-to-peer (i.e., mesh) topology. SCHC has been designed for LPWAN technologies, which are typically based on a star topology where constrained devices (e.g., sensors) communicate with a less constrained, central network gateway [RFC 8376]. However, as stated in [draft-ietf-lpwan-architecture], SCHC is generic and it can also be used in networking environments beyond the ones originally considered for SCHC. SCHC compression is applicable to both star topology and mesh topology IEEE 802.15.4 networks.

The traditional 6LoWPAN-based protocol stack for constrained devices (Figure 1, left) places the 6LoWPAN adaptation layer between IPv6 and an underlying technology such as IEEE 802.15.4. Suitable upper layer protocols include CoAP and UDP. (Note that, while CoAP has also been specified over TCP, and TCP may play a significant role in IoT environments , 6LoWPAN header compression has not been defined for TCP.) 6LoWPAN can be envisioned as a set of two main sublayers, where the upper one provides header compression, while the lower one offers fragmentation. This document defines an alternative approach for packet header compression over IEEE 802.15.4, which leads to a modified protocol stack (Figure 1, right).

This document defines the frame format to be used when a SCHC-compressed packet is carried over IEEE 802.15.4. Such format is carried as IEEE 802.15.4 frame payload. The format comprises a SCHC Dispatch Type, a SCHC Packet (i.e. a SCHC-compressed packet (RFC 8724), and Padding bits, if any). illustrates the described frame format.

Adding SCHC header compression to the panoply of header compression mechanisms used in 6LoWPAN/6Lo environments creates the need to signal when a packet header has been compressed by using SCHC. To this end, the present document specifies the SCHC Dispatch. The SCHC Dispatch indicates that the next field in the frame format is a SCHC-compressed header. The latter corresponds to a packet header that has been compressed by using SCHC. As defined in , the SCHC Header comprises a RuleID, and a compression residue. This document defines the SCHC Dispatch as a 6LoWPAN Dispatch Type for SCHC header compression, based on exploiting RFC 8025 Dispatch type space and the concept of "pages" . With the aim to minimize overhead, the present document allocates a whole page (Page 2) for the SCHC Dispatch Type: SCHC Dispatch Type bit pattern: 11110010 (Page 2) (Note: to be confirmed by IANA)) TO-DO: RuleID discussion

If SCHC header compression leads to a SCHC Packet size of a non-integer number of bytes, padding bits of value equal to zero MUST be appended to the SCHC Packet as appropriate to align to an octet boundary.

SCHC header compression may be applied to the headers of different protocols or sets of protocols. Some examples include: i) IPv6 packet headers, ii) joint IPv6 and UDP packet headers, iii) joint IPv6, UDP and CoAP packet headers, etc. IPv6 and UDP header fields MUST be compressed as per Section 10 of RFC 8724. TO-DO: adaptation of DevIID and AppIID in 802.15.4 environments CoAP header fields MUST be compressed as per Sections 4 to 6 of RFC 8824. TO-DO: provide examples for IPv6-only, IPv6/UDP and IPv6/UDP/CoAP.

After applying SCHC header compression to a packet intended for transmission, if the size of the resulting frame format (Section 4) exceeds the IEEE 802.15.4 frame payload space available, such frame format MUST be fragmented, carried and reassembled by means of 6LoWPAN fragmentation and reassembly .

This document requests the allocation of the Dispatch Type Field bit pattern 11110010 (Page 2) as SCHC Dispatch Type.

TBD

Ana Minaburo and Laurent Toutain suggested for the first time the use of SCHC in environments where 6LoWPAN has traditionally been used. Laurent Toutain made comments that helped shape this document. Carles Gomez has been funded in part by the Spanish Government through project PID2019-106808RA-I00, and by Secretaria d'Universitats i Recerca del Departament d'Empresa i Coneixement de la Generalitat de Catalunya 2017 through grant SGR 376.