6LoWPAN Working Group E. Kim Internet-Draft ETRI Intended status: Informational D. Kaspar Expires: September 9, 2010 Simula Research Laboratory C. Gomez Tech. Univ. of Catalonia/i2CAT C. Bormann Universitaet Bremen TZI March 8, 2010 Problem Statement and Requirements for 6LoWPAN Routing draft-ietf-6lowpan-routing-requirements-06 Abstract 6LoWPANs are formed by devices that are compatible with the IEEE 802.15.4 standard. However, neither the IEEE 802.15.4 standard nor the 6LoWPAN format specification define how mesh topologies could be obtained and maintained. Thus, it should be considered how 6LoWPAN formation and multi-hop routing could be supported. This document provides the problem statement and design space for 6LoWPAN routing. It defines the routing requirements for 6LoWPAN networks, considering the low-power and other particular characteristics of the devices and links. The purpose of this document is not to recommend specific solutions, but to provide general, layer-agnostic guidelines about the design of 6LoWPAN routing, which can lead to further analysis and protocol design. This document is intended as input to groups working on routing protocols relevant to 6LoWPAN, such as the IETF ROLL WG. Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. Kim, et al. Expires September 9, 2010 [Page 1] Internet-Draft 6LoWPAN Routing Requirements March 2010 The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on September 9, 2010. Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License. This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Kim, et al. Expires September 9, 2010 [Page 2] Internet-Draft 6LoWPAN Routing Requirements March 2010 Table of Contents 1. Problem Statement . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Design Space . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1. Reference Network Model . . . . . . . . . . . . . . . . . 8 3.2. 6LoWPAN Headers for Routing . . . . . . . . . . . . . . . 9 4. Scenario Considerations and Parameters for 6LoWPAN Routing . . 11 5. 6LoWPAN Routing Requirements . . . . . . . . . . . . . . . . . 16 5.1. Support of 6LoWPAN Device Properties . . . . . . . . . . . 16 5.2. Support of 6LoWPAN Link Properties . . . . . . . . . . . . 18 5.3. Support of 6LoWPAN Network Characteristics . . . . . . . . 20 5.4. Support of Security . . . . . . . . . . . . . . . . . . . 24 5.5. Support of Mesh-under Forwarding . . . . . . . . . . . . . 25 6. Security Considerations . . . . . . . . . . . . . . . . . . . 27 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 28 8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 29 9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 30 9.1. Normative References . . . . . . . . . . . . . . . . . . . 30 9.2. Informative References . . . . . . . . . . . . . . . . . . 30 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 33 Kim, et al. Expires September 9, 2010 [Page 3] Internet-Draft 6LoWPAN Routing Requirements March 2010 1. Problem Statement 6LoWPANs are formed by devices that are compatible with the IEEE 802.15.4 standard [IEEE802.15.4]. Most of the LoWPAN devices are distinguished by their low bandwidth, short range, scarce memory capacity, limited processing capability and other attributes of inexpensive hardware. The characteristics of nodes participating in LoWPANs are assumed to be those described in the 6LoWPAN problem statement [RFC4919], and the IPv6 over IEEE 802.15.4 [RFC4944] document which has specified how to carry IPv6 packets over IEEE 802.15.4 and similar networks. IEEE 802.15.4 networks support star and mesh topologies. However, neither the IEEE 802.15.4 standard nor the 6LoWPAN format specification ([RFC4944]) define how mesh topologies could be obtained and maintained. Thus, 6LoWPAN formation and multi-hop routing should be supported by either at below IP layer (the adaptation layer or LLC) or the IP layer. A number of IP routing protocols have been developed in various IETF working groups. However, these existing routing protocols may not satisfy the requirements of multi-hop routing in 6LoWPANs, for the following reasons: o 6LoWPAN nodes have special types and roles, such as nodes drawing their power from primary batteries, power-affluent nodes, mains- powered and high-performance gateways, data aggregators, etc. 6LoWPAN routing protocols should support multiple device types and roles. o More stringent requirements apply to LoWPANs, as opposed to higher performance or non-battery-operated networks. 6LoWPAN nodes are characterized by small memory sizes, low processing power, and are running on very limited power supplied by primary non-rechargeable batteries (a few KBytes of RAM, a few dozens of KBytes of ROM/ flash memory, and a few MHz of CPU is typical). A node's lifetime is usually defined by the lifetime of its battery. o Handling sleeping nodes is very critical in LoWPANs, more than in traditional ad-hoc networks. LoWPAN nodes might stay in sleep mode for most of the time. Taking advantage of appropriate times for transmissions is important for efficient packet forwarding. o Routing in 6LoWPANs might possibly translate to a simpler problem than routing in higher-performance networks. LoWPANs might be either transit networks or stub networks. Under the assumption that LoWPANs are never transit networks (as implied by [RFC4944]), routing protocols may be drastically simplified. This document will focus on the requirements for stub networks. Additional Kim, et al. Expires September 9, 2010 [Page 4] Internet-Draft 6LoWPAN Routing Requirements March 2010 requirements may apply to transit networks. o Routing in LoWPANs might possibly translate to a harder problem than routing in higher-performance networks. Routing in LoWPANs requires power optimization, stable operation in lossy environments, data-aware routing, etc. These requirements are not easily satisfiable all at once [I-D.ietf-roll-protocols-survey]. These properties create new challenges on obtaining robust and reliable routing within LoWPANs. The 6LoWPAN problem statement document ("6LoWPAN Problems and Goals" [RFC4919]) briefly mentions four requirements on routing protocols: (a) low overhead on data packets (b) low routing overhead (c) minimal memory and computation requirements (d) support for sleeping nodes considering battery saving These four high-level requirements describe the basic requirements for 6LoWPAN routing. Based on the fundamental features of 6LoWPAN, more detailed routing requirements are presented in this document, which can lead to further analysis and protocol design. Considering the problems above, detailed 6LoWPAN routing requirements must be defined. Application-specific features affect the design of 6LoWPAN routing requirements and the corresponding solutions. However, various applications can be profiled by similar technical characteristics, although the related detailed requirements might differ (e.g., a few dozens of nodes in a home lighting system need appropriate scalability for its applications, while millions of nodes for a highway infrastructure system also need appropriate scalability). This routing requirements document states the routing requirements of 6LoWPAN applications in general, providing examples for different cases of routing. It does not imply a single routing solution to be favorable for all 6LoWPAN applications. Kim, et al. Expires September 9, 2010 [Page 5] Internet-Draft 6LoWPAN Routing Requirements March 2010 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Readers are expected to be familiar with all the terms and concepts that are discussed in "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals" [RFC4919], and "Transmission of IPv6 Packets over IEEE 802.15.4 Networks" [RFC4944]. This specification makes use of the terminology defined in the "Neighbor Discovery for 6LoWPAN" [I-D.ietf-6lowpan-nd]. Kim, et al. Expires September 9, 2010 [Page 6] Internet-Draft 6LoWPAN Routing Requirements March 2010 3. Design Space Apart from a wide variety of conceivable routing algorithms for 6LoWPAN, it is possible to perform routing in the IP-layer, using a Route Over approach or in the adaptation layer defined by the 6LoWPAN format document [RFC4944], using the Mesh Under approach (see Figure 1). The Route Over approach relies on IP routing and therefore supports routing over possibly various types of interconnected links. Note: The ROLL WG is now working on Route Over approaches for Low power and Lossy Networks (LLNs), not specifically for 6LoWPAN. This document focuses on 6LoWPAN-specific requirements; it may be used in conjunction with the more application-oriented requirements defined by the ROLL WG. The Mesh Under approach performs the multi-hop communication below the IP link. The most significant consequence of Mesh Under mechanism is that the characteristics of IEEE 802.15.4 directly affect the 6LoWPAN routing mechanisms, including the use of 64-bit (or 16-bit short) MAC addresses instead of IP addresses. A 6LoWPAN would therefore be seen as a single IP link. Most statements in this document consider both the Route Over and Mesh Under cases. Kim, et al. Expires September 9, 2010 [Page 7] Internet-Draft 6LoWPAN Routing Requirements March 2010 Figure 1 shows the place of 6LoWPAN routing in the entire network stack. +-----------------------------+ +-----------------------------+ | Application Layer | | Application Layer | +-----------------------------+ +-----------------------------+ | Transport Layer (TCP/UDP) | | Transport Layer (TCP/UDP) | +-----------------------------+ +-----------------------------+ | Network Layer (IPv6) | | Network +---------+ | +-----------------------------+ | Layer | Routing | | | 6LoWPAN +---------+ | | (IPv6) +---------+ | | Adaptation | Routing*| | +-----------------------------+ | Layer +---------+ | | 6LoWPAN Adaptation Layer | +-----------------------------+ +-----------------------------+ | IEEE 802.15.4 (MAC) | | IEEE 802.15.4 (MAC) | +-----------------------------+ +-----------------------------+ | IEEE 802.15.4 (PHY) | | IEEE 802.15.4 (PHY) | +-----------------------------+ +-----------------------------+ * Here, 'Routing' is not equivalent to IP routing, but includes the functionalities of path computation and forwarding under the IP layer. Figure 1: Mesh Under (left) and Route Over routing (right) In order to avoid packet fragmentation and the overhead for reassembly, routing packets should fit into a single IEEE 802.15.4 physical frame and application data should not be expanded to an extent that they no longer fit. 3.1. Reference Network Model For multi-hop communication in 6LoWPAN, when a Route Over mechanism is in use, all LoWPAN Routers perform IP routing within the stub network. Not only the ER but also other intermediate nodes become LoWPAN Routers and perform standard Layer 3 (IP) routing (see Figure 2). In this case, the link-local scope covers the set of nodes within symmetric radio range of a node. When a 6LoWPAN follows the Mesh Under configuration, the LoWPAN Edge Router (ER) is the only IPv6 router in the 6LoWPAN (see Figure 3). This means that the IPv6 link-local scope includes all nodes in the LoWPAN. For this, a Mesh Under mechanism MUST be provided to support multi-hop transmission. Kim, et al. Expires September 9, 2010 [Page 8] Internet-Draft 6LoWPAN Routing Requirements March 2010 h h / | ER: Edge Router ER --- r --- r --- h r: LoWPAN Router / \ h: LoWPAN Host h r --- h | / \ r - r -- h Figure 2: An example of a Route Over LoWPAN h h / | ER: Edge Router ER --- m --- m --- h m: Mesh Node / \ h: LoWPAN Host h m --- h | / \ m - m -- h Figure 3: An example of a Mesh Under LoWPAN When multiple 6LoWPANs are formed with globally unique IPv6 addresses in the 6LoWPANs, and node (a) of 6LoWPAN [A] wants to communicate with node (b) of 6LoWPAN [B], the normal IPv6 mechanisms will be employed. For Route Over, the IPv6 address of (b) is set as the destination of the packets, and the nodes perform IP routing to the ER for these outgoing packets. Additionally, a default route to the ER could be inserted into the 6LoWPAN routing system. For Mesh Under, there is one IP hop from a node (a) to ER of [A], no matter how many radio hops they are apart from each other. This, of course, assumes the existence of a Mesh Under routing protocol in order to reach the ER. 3.2. 6LoWPAN Headers for Routing When a Route Over mechanism is built over the IPv6 layer, the Dispatch value can be chosen as one of the Dispatch patterns for 6LoWPAN, followed by a compressed or uncompressed IPv6 header, and Route Over routing header will be included in the payload of IPv6 packet. The 6LoWPAN compression format for IPv6 Datagrams [I-D.ietf-6lowpan-hc] includes next header compression (NHC) and the routing header could be followed by NHC. Kim, et al. Expires September 9, 2010 [Page 9] Internet-Draft 6LoWPAN Routing Requirements March 2010 Figure 4 depicts an example of 6LoWPAN encapsulated Route Over routing packets for the new header compression format defined in [I-D.ietf-6lowpan-hc]: +------------------------+-------------+------------------------+-- |Dispatch + LOWPAN_IPHC | IPv6 Header | Payload(Routing packet)|... +------------------------+-------------+------------------------+-- +------------------------+-------------+-----+----------------+-- |Dispatch + LOWPAN_IPHC | IPv6 Header | NHC | Routing header |... +------------------------+-------------+-----+----------------+-- Figure 4: 6LoWPAN IPHC packet format and Route Over routing In the simplest case for a Mesh Under where layer two forwarding can be performed without piggy-backing routing protocol information, the mesh-header defined in RFC 4944 [RFC4944] is sufficient, see Figure 5. Frame Delivery in a Link-Layer Mesh is described in the Section 11 in RFC 4944. 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1 0|V|F|HopsLft| originator address, final address +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: 6LoWPAN Mesh Header However, beyond the mesh header, additional information may need to be transmitted for full routing functionality. If a Mesh Under routing protocol is built for operation in 6LoWPAN's adaptation layer, routing control packets with MAC addresses are placed after the 6LoWPAN Dispatch. A new Dispatch value is REQUIRED to be assigned, see Figure 6. As shown in Figure 6, multiple routing protocols can be supported by the usage of different Dispatch bit sequences. +---------------------+----------------+---------+---- | Dispatch (new val.) | Routing header | ... +---------------------+----------------+---------+---- Figure 6: 6LoWPAN packet format with a Mesh Under mechanism Kim, et al. Expires September 9, 2010 [Page 10] Internet-Draft 6LoWPAN Routing Requirements March 2010 4. Scenario Considerations and Parameters for 6LoWPAN Routing IP-based LoWPAN technology is still in its early stage of development, but the range of conceivable usage scenarios is tremendous. The numerous possible applications of sensor networks make it obvious that mesh topologies will be prevalent in LoWPAN environments and robust routing will be a necessity for expedient communication. Research efforts in the area of sensor networking have put forth a large variety of multi-hop routing algorithms [refs.bulusu]. Most related work focuses on optimizing routing for specific application scenarios, which can be realized using several models of communication, including the following ones [refs.cctc]: o Flooding (in very small networks) o Hierarchical routing o Geographic routing o Self-organizing coordinate routing Depending on the topology of a LoWPAN and the application(s) running over it, different types of routing may be used. However, this document abstracts from application-specific communication and describes general routing requirements valid for overall routing in LoWPANs. The following parameters can be used to describe specific scenarios in which the candidate routing protocols could be evaluated. a. Network Properties: * Number of Devices, Density and Network Diameter: These parameters usually affect the routing state directly (e.g. the number of entries in a routing table or neighbor list). Especially in large and dense networks, policies must be applied for discarding "low-quality" and stale routing entries in order to prevent memory overflow. * Connectivity: Due to external factors or programmed disconnections, a LoWPAN can be in several states of connectivity; anything in the range from "always connected" to "rarely connected". This poses great challenges to the dynamic discovery of routes across a LoWPAN. * Dynamicity (including mobility): Location changes can be induced by unpredictable external Kim, et al. Expires September 9, 2010 [Page 11] Internet-Draft 6LoWPAN Routing Requirements March 2010 factors or by controlled motion, which may in turn cause route changes. Also, nodes may dynamically be introduced into a LoWPAN and removed from it later. The routing state and the volume of control messages may heavily depend on the number of moving nodes in a LoWPAN and their speed, as well as how quickly and frequently environmental characteristics influencing radio propagation change. * Deployment: In a LoWPAN, it is possible for nodes to be scattered randomly or to be deployed in an organized manner. The deployment can occur at once, or as an iterative process, which may also affect the routing state. * Spatial Distribution of Nodes and Gateways: Network connectivity depends on the spatial distribution of the nodes, and on other factors such as device number, density and transmission range. For instance, nodes can be placed on a grid, or can be randomly placed in an area (as can be modeled by a bidimensional Poisson distribution), etc. In addition, if the LoWPAN is connected to other networks through infrastructure nodes called gateways, the number and spatial distribution of gateways affects network congestion and available data rate, among others. * Traffic Patterns, Topology and Applications: The design of a LoWPAN and the requirements on its application have a big impact on the network topology and the most efficient routing type to be used. For different traffic patterns (point-to-point, multipoint-to-point, point-to- multipoint) and network architectures, various routing mechanisms have been developed, such as data-aware, event- driven, address-centric, and geographic routing. * Classes of Service: For mixing applications of different criticality on one LoWPAN, support of multiple classes of service may be required in resource-constrained LoWPANs and may require a certain degree of routing protocol overhead. * Security: LoWPANs may carry sensitive information and require a high level of security support where the availability, integrity, and confidentiality of data are of prime relevance. Secured messages cause overhead and affect the power consumption of LoWPAN routing protocols. Kim, et al. Expires September 9, 2010 [Page 12] Internet-Draft 6LoWPAN Routing Requirements March 2010 b. Node Parameters: * Processing Speed and Memory Size: These basic parameters define the maximum size of the routing state and the maximum complexity of its processing. LoWPAN nodes may have different performance characteristics. * Power Consumption and Power Source: The number of battery- and mains-powered nodes and their positions in the topology created by them in a LoWPAN affect routing protocols in their selection of paths that optimize network lifetime. * Transmission Range: This parameter affects routing. For example, a high transmission range may cause a dense network, which in turn results in more direct neighbors of a node, higher connectivity and a larger routing state. * Traffic Pattern: This parameter affects routing since highly loaded nodes (either because they are the source of packets to be transmitted or due to forwarding) may contribute to higher delivery delays and may consume more energy than lightly loaded nodes. This applies to both data packets and routing control messages. c. Link Parameters: This section discusses link parameters that apply to IEEE 802.15.4 legacy mode (i.e. not making use of improved modulation schemes). * Throughput: The maximum user data throughput of a bulk data transmission between a single sender and a single receiver through an unslotted IEEE 802.15.4 2.4 GHz channel in ideal conditions is as follows [refs.Latre]: + 16-bit MAC addresses, unreliable mode: 151.6 kbit/s + 16-bit MAC addresses, reliable mode: 139.0 kbit/s + 64-bit MAC addresses, unreliable mode: 135.6 kbit/s + 64-bit MAC addresses, reliable mode: 124.4 kbit/s In the case of 915 MHz band: Kim, et al. Expires September 9, 2010 [Page 13] Internet-Draft 6LoWPAN Routing Requirements March 2010 + 16-bit MAC addresses, unreliable mode: 31.1 kbit/s + 16-bit MAC addresses, reliable mode: 28.6 kbit/s + 64-bit MAC addresses, unreliable mode: 27.8 kbit/s + 64-bit MAC addresses, reliable mode: 25.6 kbit/s In the case of 868 MHz band: + 16-bit MAC addresses, unreliable mode: 15.5 kbit/s + 16-bit MAC addresses, reliable mode: 14.3 kbit/s + 64-bit MAC addresses, unreliable mode: 13.9 kbit/s + 64-bit MAC addresses, reliable mode: 12.8 kbit/s * Latency: The range of latencies, depending on payload size, of a frame transmission between a single sender and a single receiver through an unslotted IEEE 802.15.4 2.4 GHz channel in ideal conditions are as shown next [refs.Latre]. For unreliable mode, the actual latency is provided. For reliable mode, the round-trip-time including transmission of a layer two acknowledgment is provided: + 16-bit MAC addresses, unreliable mode: [1.92 ms, 6.02 ms] + 16-bit MAC addresses, reliable mode: [2.46 ms, 6.56 ms] + 64-bit MAC addresses, unreliable mode: [2.75 ms, 6.02 ms] + 64-bit MAC addresses, reliable mode: [3.30 ms, 6.56 ms] For the 915 MHz band: + 16-bit MAC addresses, unreliable mode: [5.85 ms, 29.35 ms] + 16-bit MAC addresses, reliable mode: [8.35 ms, 31.85 ms] + 64-bit MAC addresses, unreliable mode: [8.95 ms, 29.35 ms] + 64-bit MAC addresses, reliable mode: [11.45 ms, 31.85 ms] For the 868 MHz band: Kim, et al. Expires September 9, 2010 [Page 14] Internet-Draft 6LoWPAN Routing Requirements March 2010 + 16-bit MAC addresses, unreliable mode: [11.7 ms, 58.7 ms] + 16-bit MAC addresses, reliable mode: [16.7 ms, 63.7 ms] + 64-bit MAC addresses, unreliable mode: [17.9 ms, 58.7 ms] + 64-bit MAC addresses, reliable mode: [22.9 ms, 63.7 ms] Kim, et al. Expires September 9, 2010 [Page 15] Internet-Draft 6LoWPAN Routing Requirements March 2010 5. 6LoWPAN Routing Requirements This section defines a list of requirements for 6LoWPAN routing. An important design property specific to low-power networks is that LoWPANs have to support multiple device types and roles, such as: o host nodes drawing their power from primary batteries or using energy harvesting (both called "power-constrained nodes" in the following) o mains-powered host nodes (an example for what we call "power- affluent nodes") o power-affluent (but not necessarily mains-powered) high- performance gateway(s) o nodes with various functionality (data aggregators, relays, local manager/coordinators, etc.) Due to these different device types and roles LoWPANs need to consider the following two primary attributes: o Power conservation: some devices are mains-powered, but many are battery-operated and need to last several months to a few years with a single AA battery. Many devices are mains-powered most of the time, but still need to function for possibly extended periods from batteries (e.g. on a construction site before building power is switched on for the first time). o Low performance: tiny devices, small memory sizes, low-performance processors, low bandwidth, high loss rates, etc. These fundamental attributes of LoWPANs affect the design of routing solutions. Whether existing routing specifications are simplified and modified, or new solutions are introduced in order to fit the low-power requirements of LoWPANs, they need to meet the requirements described in the following. 5.1. Support of 6LoWPAN Device Properties The general objectives listed in this section should be met by 6LoWPAN routing protocols. The importance of each requirement is dependent on what node type the protocol is running on and what the role of the node is. The following requirements consider the presence of battery-powered nodes in LoWPANs. [R01] 6LoWPAN routing protocols SHOULD allow implementation with small code size and require low routing state to fit the typical Kim, et al. Expires September 9, 2010 [Page 16] Internet-Draft 6LoWPAN Routing Requirements March 2010 6LoWPAN node capacity. Generally speaking, the code size is bounded by available flash memory size, and the routing table is bounded by RAM size, possibly limiting it to less than 32 entries. The RAM size of LoWPAN nodes often ranges between 4 KB (2 KB minimum) and 10 KB, and program flash memory normally consists of 48 KB to 128 KB. (e.g., in the current market, MICAz has 128 KB program flash, 4 KB EEPROM, 512 KB external flash ROM; TIP700CM has 48 KB program flash, 10 KB RAM, 1 MB external flash ROM). Due to these hardware restrictions, code SHOULD fit within a small memory size; no more than 48 KB to 128 KB of flash memory including at least a few tens of KB of application code size. (As a general observation, a routing protocol of low complexity may help achieving the goal of reducing power consumption, improves robustness, requires lower routing state, is easier to analyze, and may be less prone to security attacks.) In addition, operation with limited amounts of routing state (such as routing tables and neighbor lists) SHOULD be maintained since some typical memory sizes preclude storing state of a large number of nodes. For instance, industrial monitoring applications may need to support at maximum 20 hops [RFC5673]. Small networks can be designed to support a smaller number of hops. While the need for this is highly dependent on the network architecture, there should be at least one mode of operation that can function with 32 forwarding entries or less. [R02] 6LoWPAN routing protocols SHOULD cause minimal power consumption by the efficient use of control packets (e.g., minimize expensive IP multicast which causes link broadcast to the entire LoWPAN) and by the efficient routing of data packets. One way of battery lifetime optimization is by achieving a minimal control message overhead. Compared to functions such as computational operations or taking sensor samples, radio communications is by far the dominant factor of power consumption [refs.SmartDust]. Power consumption of transmission and/or reception depends linearly on the length of data units and on the frequency of transmission and reception of the data units [refs.Shih]. The energy consumption of two example RF controllers for low-power nodes is shown in [refs.Hill]. The TR1000 radio consumes 21 mW when transmitting at 0.75 mW, and 15 mW on reception (with a receiver sensitivity of -85 dBm). The CC1000 consumes 31.6 mW when transmitting 0.75 mW, and 20 mW for receiving (with a receiver sensitivity of -105 dBm). The power endurance under the Kim, et al. Expires September 9, 2010 [Page 17] Internet-Draft 6LoWPAN Routing Requirements March 2010 concept of an idealized power source is explained in [refs.Hill]. Based on the energy of an idealized AA battery, the CC1000 can transmit for approximately 4 days straight or receive for 9 consecutive days. Note that availability for reception consumes power as well. As multicast may cause flooding in the LoWPAN, a 6LoWPAN routing protocol SHOULD minimize the control cost by multicasting routing packets. Control cost of routing protocols in low power and lossy networks is discussed in more detail in [I-D.ietf-roll-protocols-survey]. 5.2. Support of 6LoWPAN Link Properties 6LoWPAN links have the characteristics of low data rate and possibly high loss rates. The routing requirements described in this section are derived from the link properties. [R03] 6LoWPAN routing protocol control messages SHOULD NOT exceed a single IEEE 802.15.4 frame size in order to avoid packet fragmentation and the overhead for reassembly. In order to save energy, routing overhead should be minimized to prevent fragmentation of frames. Therefore, 6LoWPAN routing should not cause packets to exceed the IEEE 802.15.4 frame size. This reduces the energy required for transmission, avoids unnecessary waste of bandwidth, and prevents the need for packet reassembly. As calculated in RFC4944 [RFC4944], the maximum size of a 6LoWPAN frame, in order not to cause fragmentation, is 81 octets. This may imply the use of semantic fragmentation and/or algorithms that can work on small increments of routing information. [R04] The design of routing protocols for LoWPANs must consider the fact that packets are to be delivered with sufficient probability according to application requirements. Requirements on successful end-to-end packet delivery ratio (where delivery may be bounded within certain latency) vary depending on applications. In industrial applications, some non-critical monitoring applications may tolerate successful delivery ratio of less than 90% with hours of latency; in some other cases, a delivery ratio of 99.9% is required [RFC5673]. In building automation applications, application layer errors must be below 0.01% [I-D.ietf-roll-building-routing-reqs]. Kim, et al. Expires September 9, 2010 [Page 18] Internet-Draft 6LoWPAN Routing Requirements March 2010 Successful end-to-end delivery of packets in an IEEE 802.15.4 mesh depends on the quality of the path selected by the routing protocol and on the ability of the routing protocol to cope with short-term and long-term quality variation. The metric of the routing protocol strongly influences performance of the routing protocol in terms of delivery ratio. The quality of a given path depends on the individual qualities of the links (including the devices) that compose that path. IEEE 802.15.4 settings affect the quality perceived at upper layers. In particular, in IEEE 802.15.4 reliable mode, if an acknowledgment frame is not received after a given period, the originator retries frame transmission up to a maximum number of times. If an acknowledgment frame is still not received by the sender after performing the maximum number of transmission attempts, the MAC layer assumes the transmission has failed and notifies the next higher layer of the failure. Note that excessive retransmission may be detrimental, see RFC 3819 [RFC3819]. [R05] The design of routing protocols for LoWPANs must consider the latency requirements of applications and IEEE 802.15.4 link latency characteristics. Latency requirements may differ from a few hundreds milliseconds to minutes, depending on the type of application. Real-time building automation applications usually need response times below 500 ms between egress and ingress, while forced entry security alerts must be routed to one or more fixed or mobile user devices within 5 s [I-D.ietf-roll-building-routing-reqs]. Non-critical closed loop applications for industrial automation have latency requirements that can be as low as 100 ms but many control loops are tolerant of latencies above 1 s [RFC5673]. In contrast to this, urban monitoring applications allow latencies smaller than the typical intervals used for reporting sensed information; for instance, in the order of seconds to minutes [RFC5548]. The range of latencies of a frame transmission between a single sender and a single receiver through an ideal unslotted IEEE 802.15.4 2.4 GHz channel is between 2.46 ms and 6.02 ms in 64 bit MAC address unreliable mode and 2.20 ms to 6.56 ms in 64 bit address reliable mode. The range of latencies of 868 MHz band is from 11.7 ms to 63.7 ms, depending on the address type and reliable/unreliable mode used. Note that the latencies may be larger than that depending on channel load, MAC layer settings procedure-->, and reliable/unreliable mode choice. Note that other MAC approaches than the legacy 802.15.4 may be used (e.g. TDMA). Duty cycling may further affect latency (see [R08]). Kim, et al. Expires September 9, 2010 [Page 19] Internet-Draft 6LoWPAN Routing Requirements March 2010 Note that a tradeoff exists between [R05] and [R04]. [R06] 6LoWPAN routing protocols SHOULD be robust to dynamic loss caused by link failure or device unavailability either in the short term (e.g. due to RSSI variation, interference variation, noise and asynchrony) or in the long term (e.g. due to a depleted power source, hardware breakdown, operating system misbehavior, etc.). An important trait of 6LoWPAN devices is their unreliability due to limited system capabilities, and also because they might be closely coupled to the physical world with all its unpredictable variation. In harsh environments, LoWPANs easily suffer from link failure. Collision or link failure easily increases send and receive queues and can lead to queue overflow and packet losses. For home applications, where users expect feedback after carrying out actions (such as handling a remote control while moving around), routing protocols must converge within 2 seconds if the destination node of the packet has moved and must converge within 0.5 seconds if only the sender has moved [I-D.ietf-roll-home-routing-reqs]. The tolerance of the recovery time can vary depending on the application, however, the routing protocol must provide the detection of short-term unavailability and long-term disappearance. The routing protocol has to exploit network resources (e.g. path redundancy) to offer good network behavior despite of node failure. [R07] 6LoWPAN routing protocols SHOULD be designed to correctly operate in the presence of link asymmetry. Link asymmetry occurs when the probability of successful transmission between two nodes is significantly higher in one direction than in the other one. This phenomenon has been reported in a large number of experimental studies and it is expected that 6LoWPANs will exhibit link asymmetry. 5.3. Support of 6LoWPAN Network Characteristics 6LoWPANs can be deployed in different sizes and topologies, adhere to various models of mobility, be exposed to various levels of interference, etc. In any case, LoWPANs must maintain low energy consumption. The requirements described in the following subsection are derived from the network attributes of 6LoWPANs. [R08] 6LoWPAN routing protocols SHOULD be reliable despite unresponsive nodes due to periodic hibernation. Kim, et al. Expires September 9, 2010 [Page 20] Internet-Draft 6LoWPAN Routing Requirements March 2010 Many nodes in LoWPAN environments might periodically hibernate (i.e. disable their transceiver activity) in order to save energy. Therefore, routing protocols must ensure robust packet delivery despite nodes frequently shutting off their radio transmission interface. Feedback from the lower IEEE 802.15.4 layer may be considered to enhance the power-awareness of 6LoWPAN routing protocols. CC1000-based nodes must operate at a duty cycle of approximately 2% to survive for one year from idealized AA battery power source [refs.Hill]. For home automation purposes, it is suggested that the devices have to maximize the sleep phase with a duty cycle lower than 1% [I-D.ietf-roll-home-routing-reqs], while in building automation applications, batteries must be operational for at least 5 years when the sensing devices are transmitting data (e.g. 64 bytes) once per minute [I-D.ietf-roll-building-routing-reqs]. Dependent on the application in use, packet rates may range from one per second to one per day or beyond. Routing protocols may take advantage of knowledge about the packet transmission rate and utilize this information in calculating routing paths. [R09] The metric used by 6LoWPAN routing protocols MAY utilize a combination of the inputs provided by the lower layers and other measures to optimize path selection considering energy balance and link qualities. In homes, buildings, or infrastructure, some nodes will be installed with mains power. Such power-installed nodes MUST be considered as relay points for a prominent role in packet delivery. 6LoWPAN routing protocols MUST know the power constraints of the nodes. Simple hop-count-only mechanisms may be inefficient in 6LoWPANs. There is a Link Quality Indication (LQI), or/and RSSI from IEEE 802.15.4 that may be taken into account for better metrics. The metric to be used (and its goal) may depend on applications and requirements. The numbers in Figure 7 represent the Link Delivery Ratio (LDR) of each pair of nodes. There are studies that show a piecewise linear dependence between LQI and LDR [refs.Chen]. Kim, et al. Expires September 9, 2010 [Page 21] Internet-Draft 6LoWPAN Routing Requirements March 2010 0.6 A-------C \ / 0.9 \ / 0.9 \ / B Figure 7: An example network In this simple example, there are two options in routing from node A to node C, with the following features: A. Path AC: + (1/0.6) = 1.67 avg. transmissions needed for each packet (confirmed link layer delivery with retransmissions and negligible ACK loss have been assumed) + one-hop path + good in energy consumption and end-to-end latency of data packets, bad in delivery ratio (0.6) + bad in probability of route reconfigurations B. Path ABC: + (1/0.9)+(1/0.9) = 2.22 avg. transmissions needed for each packet (under the same assumptions as above) + two-hop path + bad in energy consumption and end-to-end latency of data packets, good in delivery ratio (0.81) If energy consumption of the network must be minimized, path AC is the best (this path would be chosen based on a hop count metric). However, if the delivery ratio in that case is not sufficient, the best path is ABC (it would be chosen by an LQI based metric). Combinations of both metrics can be used. The metric also affects the probability of route reconfiguration. Route reconfiguration, which may be triggered by packet losses, may require transmission of routing protocol messages. It is possible to use a metric aimed at selecting the path with low route reconfiguration rate by using LQI as an input to the metric. Such a path has good properties, including stability and low control message overhead. Kim, et al. Expires September 9, 2010 [Page 22] Internet-Draft 6LoWPAN Routing Requirements March 2010 [R10] 6LoWPAN routing protocols SHOULD be designed to achieve both scalability from a few nodes to maybe millions of nodes and minimality in terms of used system resources. A LoWPAN may consist of just a couple of nodes (for instance in a body-area network), but may also contain much higher numbers of devices (e.g. monitoring of a city infrastructure or a highway). For home automation applications it is envisioned that the routing protocol must support 250 devices in the network [I-D.ietf-roll-home-routing-reqs], while routing protocols for metropolitan-scale sensor networks must be capable of clustering a large number of sensing nodes into regions containing on the order of 10^2 to 10^4 sensing nodes each [RFC5548]. It is therefore necessary that routing mechanisms are designed to be scalable for operation in various network sizes. However, due to a lack of memory size and computational power, 6LoWPAN routing might limit forwarding entries to a small number, such as at maximum 32 routing table entries. [R11] The procedure of route repair and related control messages should not harm overall energy consumption from the routing protocols. Local repair improves throughput and end-to-end latency, especially in large networks. Since routes are repaired quickly, fewer data packets are dropped, and a smaller number of routing protocol packet transmissions are needed since routes can be repaired without source initiated Route Discovery [refs.Lee]. One important consideration here may be to avoid premature energy depletion, even in case that impairs other requirements. [R12] 6LoWPAN routing protocols SHOULD allow for dynamically adaptive topologies and mobile nodes. When supporting dynamic topologies and mobile nodes, route maintenance should keep in mind the goal of a minimal routing state and routing protocol message overhead. Building monitoring applications, for instance, require that the mobile devices SHOULD be capable of leaving (handing-off) from an old network joining onto a new network within 15 seconds [I-D.ietf-roll-building-routing-reqs]. More interactive applications such as used in home automation systems, where users are giving input and expect instant feedback, mobility requirements are also stricter and, for moves within a network, a convergence time below 0.5 seconds is commonly required [I-D.ietf-roll-home-routing-reqs]. In industrial environments, where mobile equipment such as cranes move around, the support of vehicular speeds of up to 35 km/h are required to be supported by the routing protocol [RFC5673]. Currently, 6LoWPANs are not Kim, et al. Expires September 9, 2010 [Page 23] Internet-Draft 6LoWPAN Routing Requirements March 2010 normally being used for such a fast mobility, but dynamic association and disassociation MUST be supported in 6LoWPAN. There are several challenges that should be addressed by a 6LoWPAN routing protocol in order to create robust routing in dynamic environments: * Mobile nodes changing their location inside a LoWPAN: If the nodes' movement pattern is unknown, mobility cannot easily be detected or distinguished by the routing protocols. Mobile nodes can be treated as nodes that disappear and re- appear in another place. Movement pattern tracking increases complexity and can be avoided by handling moving nodes using reactive route updates. * Movement of a LoWPAN with respect to other (inter)connected LoWPANs: Within stub networks, more powerful gateway nodes need to be configured to handle moving LoWPANs. * Nodes permanently joining or leaving the LoWPAN: In order to ease routing table updates, reduce their size, and minimize error control messages, nodes leaving the network may announce their disassociation to the closest edge router or if any, to a specific node which takes charge of local association and disassociation. [R13] A 6LoWPAN routing protocol SHOULD support various traffic patterns: point-to-point, point-to-multipoint, and multipoint-to- point, while avoiding excessive multicast traffic in a LoWPAN. 6LoWPANs often have point-to-multipoint or multipoint-to-point traffic patterns. Many emerging applications include point-to- point communication as well. 6LoWPAN routing protocols should be designed with the consideration of forwarding packets from/to multiple sources/destinations. Current documents of the ROLL working group explain that the workload or traffic pattern of use cases for LoWPANs tends to be highly structured, unlike the any- to-any data transfers that dominate typical client and server workloads. In many cases, exploiting such structure may simplify difficult problems arising from resource constraints or variation in connectivity. 5.4. Support of Security The routing requirement described in this subsection allows secure transmission of routing messages. Solutions may take into account the specific features of IEEE 802.15.4 MAC layers. Kim, et al. Expires September 9, 2010 [Page 24] Internet-Draft 6LoWPAN Routing Requirements March 2010 [R14] 6LoWPAN protocols SHOULD support secure delivery of control messages. A minimal security level can be achieved by utilizing the AES-based mechanism provided by IEEE 802.15.4. Security threats within LoWPANs may be different from existing threat models in ad-hoc network environments. Neighbor Discovery in IEEE 802.15.4 links may be susceptible to threats as listed in RFC3756 [RFC3756]. Bootstrapping may also impose additional threats. Security is also very important for designing robust routing protocols, but it should not cause significant transmission overhead. While there are applications which require very high security, such as in traffic control, other applications are less easily harmed by wrong node behavior, such as a home entertainment system. The IEEE 802.15.4 MAC provides an AES-based security mechanism. Routing protocols need to define how this mechanism can be used to obtain the intended security, either for the routing protocol alone or in conjunction with the security used for the data. Byte overhead of the mechanism, which depends on the security services selected, must be considered. In the worst case in terms of overhead, the mechanism consumes 21 bytes of MAC payload. IEEE 802.15.4 does not specify protection for acknowledgement frames. Since the sequence numbers of data frames are sent in the clear, an adversary can forge an acknowledgement for each data frame. This weakness can be combined with targeted jamming to prevent delivery of selected packets. In consequence, IEEE 802.15.4 acknowledgements cannot be relied upon. In applications that require high security, the routing protocol must not exploit feedback from acknowledgements (e.g. to keep track of neighbor connectivity, see [R16]). 5.5. Support of Mesh-under Forwarding One LoWPAN may be built as one IPv6 link. In this case, Mesh Under forwarding/routing mechanisms must be supported. The routing requirements described in this subsection allow optimization and correct operation of routing solutions taking into account the specific features of the mesh-under configuration. [R15] When a routing protocol operates in 6LoWPAN's adaptation layer, routing tables and neighbor lists MUST support 16-bit short and 64- bit extended addresses. [R16] In order to perform discovery and maintenance of neighbors (i.e., neighborhood discovery as opposed to ND-style neighbor discovery), LoWPAN Nodes SHOULD avoid sending separate "Hello" Kim, et al. Expires September 9, 2010 [Page 25] Internet-Draft 6LoWPAN Routing Requirements March 2010 messages. Instead, link-layer mechanisms (such as acknowledgments) MAY be utilized to keep track of active neighbors. Reception of an acknowledgement after a frame transmission may render unnecessary the transmission of explicit Hello messages, for example. In a more general view, any frame received by a node may be used as an input to evaluate the connectivity between the sender and receiver of that frame. [R17] In case there are one or more nodes allocated for the specific role of local management, such a management node MAY take the role of keeping track of nodes within the area of the LoWPAN it takes responsibility for. [R18] If the routing protocol functionality includes enabling IP multicast, then it may want to employ structure in the network for efficient distribution [I-D.ietf-manet-smf], such as Connected Dominating Sets (CDS), Multi-Point Relays (MPR), or relay points sending point-to-multipoint messages in unicast messages instead of using link-layer multicast (broadcast). Kim, et al. Expires September 9, 2010 [Page 26] Internet-Draft 6LoWPAN Routing Requirements March 2010 6. Security Considerations Security issues are described in Section 4.4 of the security considerations of RFC 4919 [RFC4919] and RFC 4944 [RFC4944] apply as well. The use of wireless links renders a 6LoWPAN susceptible to attacks like any other wireless network. In outdoor 6LoWPANs, the physical exposure of the nodes allows an adversary to capture, clone or tamper with these devices. In ad-hoc 6LoWPANs that are dynamic in both their topology and node memberships, a static security configuration does not suffice. Spoofed, altered, or replayed routing information might occur while multihopping could delay the detection and treatment of attacks. This specification expects that the link layer is sufficiently protected, either by means of physical or IP security for the backbone link or with MAC sublayer cryptography. However, link-layer encryption and authentication may not be sufficient to provide data confidentiality, data authentication, data integrity, and data freshness. Time synchronization, self-organization and secure localization for multi-hop routing are also critical to support. For secure multi-hop routing it may be necessary to consider authenticated broadcast (and multicast) and bidirectional link verification. Multi-path routing could be considered for increasing security to prevent selective forwarding. However, the challenge is that 6LoWPANs already have high resource constraints, so that ER and LoWPAN nodes may require different security solutions. Kim, et al. Expires September 9, 2010 [Page 27] Internet-Draft 6LoWPAN Routing Requirements March 2010 7. IANA Considerations This document has no actions for IANA. Kim, et al. Expires September 9, 2010 [Page 28] Internet-Draft 6LoWPAN Routing Requirements March 2010 8. Acknowledgements The authors thank Myung-Ki Shin for giving the idea of writing this draft. The authors also thank S. Chakrabarti who gave valuable comments for mesh-under requirements and A. Petrescu for significant review. Kim, et al. Expires September 9, 2010 [Page 29] Internet-Draft 6LoWPAN Routing Requirements March 2010 9. References 9.1. Normative References [IEEE802.15.4] IEEE Computer Society, "IEEE Std. 802.15.4-2006 (as amended)", 2007. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3756] Nikander, P., Kempf, J., and E. Nordmark, "IPv6 Neighbor Discovery (ND) Trust Models and Threats", RFC 3756, May 2004. [RFC3819] Karn, P., Bormann, C., Fairhurst, G., Grossman, D., Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L. Wood, "Advice for Internet Subnetwork Designers", BCP 89, RFC 3819, July 2004. [RFC4919] Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs): Overview, Assumptions, Problem Statement, and Goals", RFC 4919, August 2007. [RFC4944] Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks", RFC 4944, September 2007. [RFC5548] Dohler, M., Watteyne, T., Winter, T., and D. Barthel, "Routing Requirements for Urban Low-Power and Lossy Networks", RFC 5548, May 2009. [RFC5673] Pister, K., Thubert, P., Dwars, S., and T. Phinney, "Industrial Routing Requirements in Low-Power and Lossy Networks", RFC 5673, October 2009. 9.2. Informative References [I-D.ietf-6lowpan-hc] Hui, J. and P. Thubert, "Compression Format for IPv6 Datagrams in 6LoWPAN Networks", draft-ietf-6lowpan-hc-06 (work in progress), October 2009. [I-D.ietf-6lowpan-nd] Shelby, Z., Thubert, P., Hui, J., Chakrabarti, S., Bormann, C., and E. Nordmark, "6LoWPAN Neighbor Discovery", draft-ietf-6lowpan-nd-08 (work in progress), Kim, et al. Expires September 9, 2010 [Page 30] Internet-Draft 6LoWPAN Routing Requirements March 2010 February 2010. [I-D.ietf-manet-smf] Macker, J. and S. Team, "Simplified Multicast Forwarding", draft-ietf-manet-smf-09 (work in progress), July 2009. [I-D.ietf-roll-building-routing-reqs] Martocci, J., Riou, N., Mil, P., and W. Vermeylen, "Building Automation Routing Requirements in Low Power and Lossy Networks", draft-ietf-roll-building-routing-reqs-09 (work in progress), January 2010. [I-D.ietf-roll-home-routing-reqs] Brandt, A. and J. Buron, "Home Automation Routing Requirements in Low Power and Lossy Networks", draft-ietf-roll-home-routing-reqs-11 (work in progress), January 2010. [I-D.ietf-roll-protocols-survey] Tavakoli, A., Dawson-Haggerty, S., and P. Levis, "Overview of Existing Routing Protocols for Low Power and Lossy Networks", draft-ietf-roll-protocols-survey-07 (work in progress), April 2009. [refs.Chen] Chen, B., Muniswamy-Reddy, K., and M. Welsh, "Ad-Hoc Multicast Routing on Resource-Limited Sensor Nodes", 2006. [refs.Hill] Hill, J., "System Architecture for Wireless Sensor Networks". [refs.Latre] Latre, M., De Mil, P., Moerman, I., Dhoedt, B., and P. Demeester, "Throughput and Delay Analysis of Unslotted IEEE 802.15.4", May 2006. [refs.Lee] Lee, S., Belding-Royer, E., and C. Perkins, "Scalability Study of the Ad Hoc On-Demand Distance-Vector Routing Protocol", March 2003. [refs.Shih] Shih, E., "Physical Layer Driven Protocols and Algorithm Design for Energy-Efficient Wireless Sensor Networks", July 2001. [refs.SmartDust] Kim, et al. Expires September 9, 2010 [Page 31] Internet-Draft 6LoWPAN Routing Requirements March 2010 Pister, K. and B. Boser, "Smart Dust: Wireless Networks of Millimeter-Scale Sensor Nodes". [refs.bulusu] Bulusu, N. and S. Jha, "Wireless Sensor Networks", July 2005. [refs.cctc] Lu, J., Valois, F., Dohler, M., and D. Barthel, "Quantifying Organization by Means of Entropy", 2008. Kim, et al. Expires September 9, 2010 [Page 32] Internet-Draft 6LoWPAN Routing Requirements March 2010 Authors' Addresses Eunsook Eunah Kim ETRI 161 Gajeong-dong Yuseong-gu Daejeon 305-700 Korea Phone: +82-42-860-6124 Email: eunah.ietf@gmail.com Dominik Kaspar Simula Research Laboratory Martin Linges v 17 Snaroya 1367 Norway Phone: +47-6782-8223 Email: dokaspar.ietf@gmail.com Carles Gomez Tech. Univ. of Catalonia/i2CAT Escola Politecnica Superior de Castelldefels Avda. del Canal Olimpic, 15 Castelldefels 08860 Spain Phone: +34-93-413-7206 Email: carlesgo@entel.upc.edu Carsten Bormann Universitaet Bremen TZI Postfach 330440 Bremen D-28359 Germany Phone: +49-421-218-63921 Fax: +49-421-218-7000 Email: cabo@tzi.org Kim, et al. Expires September 9, 2010 [Page 33]