BEHAVE WG J. Rosenberg Internet-Draft Cisco Intended status: Standards Track R. Mahy Expires: December 26, 2008 Plantronics P. Matthews (Unaffiliated) June 24, 2008 Traversal Using Relays around NAT (TURN): Relay Extensions to Session Traversal Utilities for NAT (STUN) draft-ietf-behave-turn-08 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on December 26, 2008. Abstract If a host is located behind a NAT, then in certain situations it can be impossible for that host to communicate directly with other hosts (peers) located behind other NATs. In these situations, it is necessary for the host to use the services of an intermediate node that acts as a communication relay. This specification defines a protocol, called TURN (Traversal Using Relays around NAT), that allows the host to control the operation of the relay and to exchange packets with its peers using the relay. Rosenberg, et al. Expires December 26, 2008 [Page 1] Internet-Draft TURN June 2008 The TURN protocol can be used in isolation, but is more properly used as part of the ICE (Interactive Connectivity Establishment) approach to NAT traversal. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Overview of Operation . . . . . . . . . . . . . . . . . . . . 4 2.1. Transports . . . . . . . . . . . . . . . . . . . . . . . . 6 2.2. Allocations . . . . . . . . . . . . . . . . . . . . . . . 7 2.3. Exchanging Data with Peers . . . . . . . . . . . . . . . . 8 2.4. Channels . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.5. Permissions . . . . . . . . . . . . . . . . . . . . . . . 11 2.6. Preserving vs. Non-Preserving Allocations . . . . . . . . 11 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. General Behavior . . . . . . . . . . . . . . . . . . . . . . . 13 5. Allocations . . . . . . . . . . . . . . . . . . . . . . . . . 14 6. Creating an Allocation . . . . . . . . . . . . . . . . . . . . 16 6.1. Sending an Allocate Request . . . . . . . . . . . . . . . 16 6.2. Receiving an Allocate Request . . . . . . . . . . . . . . 17 6.3. Receiving an Allocate Response . . . . . . . . . . . . . . 21 7. Refreshing an Allocation . . . . . . . . . . . . . . . . . . . 23 7.1. Sending a Refresh Request . . . . . . . . . . . . . . . . 23 7.2. Receiving a Refresh Request . . . . . . . . . . . . . . . 23 7.3. Receiving a Refresh Response . . . . . . . . . . . . . . . 24 8. Permissions . . . . . . . . . . . . . . . . . . . . . . . . . 24 9. Send and Data Indications . . . . . . . . . . . . . . . . . . 25 9.1. Sending a Send Indication . . . . . . . . . . . . . . . . 25 9.2. Receiving a Send Indication . . . . . . . . . . . . . . . 26 9.3. Receiving a UDP Datagram . . . . . . . . . . . . . . . . . 26 9.4. Receiving a Data Indication . . . . . . . . . . . . . . . 27 10. Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 10.1. Sending a ChannelBind Request . . . . . . . . . . . . . . 28 10.2. Receiving a ChannelBind Request . . . . . . . . . . . . . 28 10.3. Receiving a ChannelBind Response . . . . . . . . . . . . . 29 10.4. The ChannelData Message . . . . . . . . . . . . . . . . . 29 10.5. Sending a ChannelData Message . . . . . . . . . . . . . . 30 10.6. Receiving a ChannelData Message . . . . . . . . . . . . . 30 10.7. Relaying . . . . . . . . . . . . . . . . . . . . . . . . . 31 11. IP and ICMP . . . . . . . . . . . . . . . . . . . . . . . . . 32 11.1. IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 11.2. ICMP . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 12. New STUN Methods . . . . . . . . . . . . . . . . . . . . . . . 36 13. New STUN Attributes . . . . . . . . . . . . . . . . . . . . . 37 13.1. CHANNEL-NUMBER . . . . . . . . . . . . . . . . . . . . . . 37 13.2. LIFETIME . . . . . . . . . . . . . . . . . . . . . . . . . 37 13.3. PEER-ADDRESS . . . . . . . . . . . . . . . . . . . . . . . 37 Rosenberg, et al. Expires December 26, 2008 [Page 2] Internet-Draft TURN June 2008 13.4. DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 13.5. RELAY-ADDRESS . . . . . . . . . . . . . . . . . . . . . . 38 13.6. REQUESTED-PROPS . . . . . . . . . . . . . . . . . . . . . 38 13.7. REQUESTED-TRANSPORT . . . . . . . . . . . . . . . . . . . 38 13.8. RESERVATION-TOKEN . . . . . . . . . . . . . . . . . . . . 39 14. New STUN Error Response Codes . . . . . . . . . . . . . . . . 39 15. Security Considerations . . . . . . . . . . . . . . . . . . . 40 16. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 41 17. IAB Considerations . . . . . . . . . . . . . . . . . . . . . . 42 18. Example . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 19. Changes from Previous Versions . . . . . . . . . . . . . . . . 42 19.1. Changed from -07 to -08 . . . . . . . . . . . . . . . . . 42 19.2. Changes from -06 to -07 . . . . . . . . . . . . . . . . . 43 19.3. Changes from -05 to -06 . . . . . . . . . . . . . . . . . 45 19.4. Changes from -04 to -05 . . . . . . . . . . . . . . . . . 46 20. Open Issues . . . . . . . . . . . . . . . . . . . . . . . . . 47 21. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 47 22. References . . . . . . . . . . . . . . . . . . . . . . . . . . 48 22.1. Normative References . . . . . . . . . . . . . . . . . . . 48 22.2. Informative References . . . . . . . . . . . . . . . . . . 48 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 49 Intellectual Property and Copyright Statements . . . . . . . . . . 51 Rosenberg, et al. Expires December 26, 2008 [Page 3] Internet-Draft TURN June 2008 1. Introduction Session Traversal Utilities for NAT (STUN) [I-D.ietf-behave-rfc3489bis] provides a suite of tools for facilitating the traversal of NAT. Specifically, it defines the Binding method, which is used by a client to determine its reflexive transport address towards the STUN server. The reflexive transport address can be used by the client for receiving packets from peers, but only when the client is behind "good" NATs. In particular, if a client is behind a NAT whose mapping behavior [RFC4787] is address or address and port dependent (sometimes called "bad" NATs), the reflexive transport address will not be usable for communicating with a peer. The only reliable way to obtain a UDP transport address that can be used for corresponding with a peer through such a NAT is to make use of a relay. The relay sits on the public side of the NAT, and allocates transport addresses to clients reaching it from behind the private side of the NAT. These allocated transport addresses, called relayed transport address, are IP addresses and ports on the relay. When the relay receives a packet on one of these allocated addresses, the relay forwards it toward the client. This specification defines an extension to STUN, called TURN, that allows a client to request a relayed transport address on a TURN server. Though a relayed transport address is highly likely to work when corresponding with a peer, it comes at high cost to the provider of the relay service. As a consequence, relayed transport addresses should only be used as a last resort. Protocols using relayed transport addresses should make use of mechanisms to dynamically determine whether such an address is actually needed. One such mechanism, defined for multimedia session establishment protocols based on the offer/answer protocol in RFC 3264 [RFC3264], is Interactive Connectivity Establishment (ICE) [I-D.ietf-mmusic-ice]. TURN was originally invented to support multimedia sessions signaled using SIP. Since SIP supports forking, TURN supports multiple peers per client; a feature not supported by other approaches (e.g., SOCKS [RFC1928]). However, care has been taken in the later stages of its development to make sure that TURN is suitable for other types of applications. 2. Overview of Operation This section gives an overview of the operation of TURN. It is non- Rosenberg, et al. Expires December 26, 2008 [Page 4] Internet-Draft TURN June 2008 normative. In a typical configuration, a TURN client is connected to a private network [RFC1918] and through one or more NATs to the public Internet. On the public Internet is a TURN server. Elsewhere in the Internet are one or more peers that the TURN client wishes to communicate with. These peers may or may not be behind one or more NATs. +---------+ | | | | / | Peer A | Client's TURN // | | Host Transport Server / | | Address Address +-+ // +---------+ 10.1.1.2:17240 192.0.2.15:3478 |N|/ 192.168.100.2:16400 | | |A| | +-+ | /|T| | | | | / +-+ v | | | / 192.0.2.210:18200 +---------+ | | |+---------+ / +---------+ | | |N| || | // | | | TURN | | | v| TURN |/ | | | Client |----|A|----------| Server |------------------| Peer B | | | | |^ | |^ ^| | | | |T|| | || || | +---------+ | || +---------+| |+---------+ | || | | | || | | +-+| | | | | | | | | Client's | Peer B Server-Reflexive Relayed Transport Transport Address Transport Address Address 192.0.2.1:7000 192.0.2.15:9000 192.0.2.210:18200 Figure 1 Figure 1 shows a typical deployment. In this figure, the TURN client and the TURN server are separated by a NAT, with the client on the private side and the server on the public side of the NAT. This NAT is assumed to be a "bad" NAT; for example, it might have a mapping property of address-and-port-dependent mapping (see [RFC4787]) for a description of what this means). The client has allocated a local port on one of its addresses for use Rosenberg, et al. Expires December 26, 2008 [Page 5] Internet-Draft TURN June 2008 in communicating with the server. The combination of an IP address and a port is called a TRANSPORT ADDRESS and since this (IP address, port) combination is located on the client and not on the NAT, it is called the client's HOST transport address. The client sends TURN messages from its host transport address to a transport address on the TURN server which is known as the TURN SERVER ADDRESS. The client learns the server's address through some unspecified means (e.g., configuration), and this address is typically used by many clients simultaneously. The TURN server address is used by the client to send both commands and data to the server; the commands are processed by the TURN server, while the data is relayed on to the peers. Since the client is behind a NAT, the server sees these packets as coming from a transport address on the NAT itself. This address is known as the client's SERVER-REFLEXIVE transport address; packets sent by the server to the client's server-reflexive transport address will be forwarded by the NAT to the client's host transport address. The client uses TURN commands to allocate a RELAYED TRANSPORT ADDRESS, which is an transport address located on the TURN server. The server ensures that there is a one-to-one relationship between the client's server-reflexive transport address and the relayed transport address; thus a packet received at the relayed transport address can be unambiguously relayed by the server to the client. The client will typically communicate this relayed transport address to one or more peers through some mechanism not specified here (e.g., an ICE offer or answer [I-D.ietf-mmusic-ice]). Once this is done, the client can send data to the server to relay towards its peers. In the reverse direction, peers can send data to the the relayed transport address of the client. The server will relay this data to the client as long as the client explicitly created a permission (see Section 2.5) for the IP address of the peer. 2.1. Transports TURN as defined in this specification only allows the use of UDP between the server and the peer. However, this specification allows the use of any one of UDP, TCP, or TLS over TCP to carry the TURN messages between the client and the server. Rosenberg, et al. Expires December 26, 2008 [Page 6] Internet-Draft TURN June 2008 +----------------------------+---------------------+ | TURN client to TURN server | TURN server to peer | +----------------------------+---------------------+ | UDP | UDP | | TCP | UDP | | TLS over TCP | UDP | +----------------------------+---------------------+ If TCP or TLS over TCP is used between the client and the server, then the server will convert between stream transport and UDP transport when relaying data. TURN allows both TCP and TLS over TCP as transports in part because many firewalls are configured to not pass any UDP traffic. For TURN clients, using TLS over TCP to communicate with the TURN server provides two benefits. First, the client can be assured that the addresses of its peers are not visible to any attackers between it and the server. Second, the client may be able to communicate with TURN servers using TLS when it would not be able to communicate with the same server using TCP or UDP, due to the policy of a firewall between the TURN client and its server. In this second case, TLS between the client and TURN server facilitates traversal. There is a planned extension to TURN to add support for TCP between the server and the peers [I-D.ietf-behave-turn-tcp]. For this reason, allocations that use UDP between the server and the peers are known as UDP allocations, while allocations that use TCP between the server and the peers are known as TCP allocations. This specification describes only UDP allocations. 2.2. Allocations To allocate a relayed transport address, the client uses an Allocate transaction. The client sends a Allocate Request to the server, and the server replies with an Allocate Response containing the allocated relayed transport address. The client can include attributes in the Allocate Request that describe the type of allocation it desires (e.g., the lifetime of the allocation). And since relaying data may require lots of bandwidth, the server typically requires that the client authenticate itself using STUN's long-term credential mechanism, to show that it is authorized to use the server. Once a relayed transport address is allocated, a client must keep the allocation alive. To do this, the client periodically sends a Refresh Request to the server with the allocated related transport address. TURN deliberately uses a different method (Refresh rather than Allocate) for refreshes to ensure that the client is informed if the allocation vanishes for some reason. Rosenberg, et al. Expires December 26, 2008 [Page 7] Internet-Draft TURN June 2008 The frequency of the Refresh transaction is determined by the lifetime of the allocation. The client can request a lifetime in the Allocate Request and may modify its request in a Refresh Request, and the server always indicates the actual lifetime in the response. The client must issue a new Refresh transaction within 'lifetime' seconds of the previous Allocate or Refresh transaction. If a client no longer wishes to use an Allocation, it should do a Refresh transaction with a requested lifetime of 0. Note that sending or receiving data from a peer DOES NOT refresh the allocation. The server keeps track of the client reflexive transport address and port, the server transport address and port, and the protocol used by the client to communicate with the server. (Together known as a 5-tuple. The server remembers the 5-tuple used in the Allocate Request. Subsequent transactions between the client and the server use this same 5-tuple. In this way, the server knows which client owns the allocated relayed transport address. If the client wishes to allocate a second relayed transport address, it must use a different 5-tuple for this allocation (e.g., by using a different client host address)., While the terminology used in this document refers to 5-tuples, the TURN server can store whatever identifier it likes that yields identical results. Specifically, many implementations use a file- descriptor in place of a 5-tuple to represent a TCP connection. 2.3. Exchanging Data with Peers There are two ways for the client and peers to exchange data using the TURN server. The first way uses Send and Data indications, the second way uses channels. Common to both ways is the ability of the client to communicate with multiple peers using a single allocated relayed transport address; thus both ways include a means for the client to indicate to the server which peer to forward the data to, and for the server to indicate which peer sent the data. When using the first way, the client sends a Send indication to the TURN server containing, in attributes inside the indication, the transport address of the peer and the data to be sent to that peer. When the TURN server receives the Send Indication, it extracts the data from the Send Indication and sends it in a UDP datagram to the peer, using the allocated relay address as the source address. In the reverse direction, UDP datagrams arriving at the relay address on the TURN server are converted into Data Indications and sent to the client, with the transport address of the peer included in an attribute in the Data Indication. Rosenberg, et al. Expires December 26, 2008 [Page 8] Internet-Draft TURN June 2008 TURN TURN Peer Peer client server A B |--- Allocate Req -->| | | |<-- Allocate Resp ---| | | | | | | |--- Send (Peer A)--->| | | | |=== data ===>| | | | | | | |<== data ====| | |<-- Data (Peer A)----| | | | | | | |--- Send (Peer B)--->| | | | |=== data =================>| | | | | | |<== data ==================| |<-- Data (Peer B)----| | | Figure 2 In the figure above, the client first allocates a relayed transport address. It then sends data to Peer A using a Send Indication; at the server, the data is extracted and forwarded in a UDP datagram to Peer A, using the relayed transport address as the source transport address. When a UDP datagram from Peer A is received at the relayed transport address, the contents are placed into a Data Indication and forwarded to the client. A similar exchange happens with Peer B. 2.4. Channels For some applications (e.g. Voice over IP), the 36 bytes of overhead that a Send or Data indication adds to the application data can substantially increase the bandwidth required between the client and the server. To remedy this, TURN offers a second way for the client and server to associate data with a specific peer. This second way uses an alternate packet format known as the ChannelData message. The ChannelData message does not use the STUN header used by other TURN messages, but instead has a 4-byte header that includes a number known as a channel number. Each channel number in use is bound to a specific peer and thus serves as a shorthand for the peer's address. To bind a channel to a peer, the client sends a ChannelBind request to the server, and includes an unbound channel number and the transport address of the peer. Once the channel is bound, the client can use a ChannelData message to send the server data destined for the peer. Similarly, the server can relay data from that peer towards the client using a ChannelData message. Rosenberg, et al. Expires December 26, 2008 [Page 9] Internet-Draft TURN June 2008 Channel bindings last for 10 minutes unless refreshed. Channel bindings are refreshed by sending ChannelData messages from the client to the server, or by rebinding the channel to the peer. TURN TURN Peer Peer client server A B |--- Allocate Req -->| | | |<-- Allocate Resp ---| | | | | | | |--- Send (Peer A)--->| | | | |=== data ===>| | | | | | | |<== data ====| | |<-- Data (Peer A)----| | | | | | | |- ChannelBind Req -->| | | | (Peer A to 0x4001) | | | | | | | |<- ChannelBind Resp -| | | | | | | |-- [0x4001] data --->| | | | |=== data ===>| | | | | | | |<== data ====| | |<- [0x4001] data --->| | | | | | | |--- Send (Peer B)--->| | | | |=== data =================>| | | | | | |<== data ==================| |<-- Data (Peer B)----| | | Figure 3 The figure above shows the channel mechanism in use. The client begins by allocating a relayed transport address, and then uses that address to exchange data with Peer A. After a bit, the client decides to bind a channel to Peer A. To do this, it sends a ChannelBind request to the server, specifying the transport address of Peer A and a channel number (0x4001). After that, the client can send application data encapsulated inside ChannelData messages to Peer A: this is shown as "[0x4001] data" where 0x4001 is the channel number. Note that ChannelData messages can only be used for peers to which the client has bound a channel. In the example above, Peer A has been bound to a channel, but Peer B has not, so application data to and from Peer B uses Send and Data indications. Rosenberg, et al. Expires December 26, 2008 [Page 10] Internet-Draft TURN June 2008 Channel bindings are always initiated by the client. 2.5. Permissions To ease concerns amongst enterprise IT administrators that TURN could be used to bypass corporate firewall security, TURN includes the notion of permissions. TURN permissions mimic the address-restricted filtering mechanism of NATs that comply with [RFC4787]. The client can install a permission by sending data to a peer (or by doing certain other things). Once a permission is installed, any peer with the same IP address (the ports numbers can differ) is permitted to send data to the client. After 5 minutes, the permission times out and the server drops any UDP datagrams arriving at the relayed transport from that IP address. Note that permissions are within the context of an allocation, so adding or expiring a permission in one allocation does not affect other allocations. Data received from the peer DOES NOT refresh the permission. 2.6. Preserving vs. Non-Preserving Allocations Some applications that use TURN are quite tolerant of the different possible ways a TURN server could set the Diff-Serv, ECN, TTL / Hop Limit, and Flow Label fields in the IP header of the outgoing packet. Other applications require that the TURN server set these fields in a specific way, and also require that the TURN server relay ICMP error packets. Applications in the second class typically wish to do Path MTU Discovery or end-to-end QOS. Unfortunately, reading and manipulating fields in the IP header and relaying ICMP messages usually requires the server to have special permissions (e.g., access to RAW sockets or be loaded into the kernel), something that the person setting up the server may be unwilling or unable to grant. This is especially true when the server is part of a larger application, for example a peer-to-peer application. It is also significantly more difficult to implement this type of server than just relaying at the UDP layer. To allow TURN to cater to both usage scenarios, TURN defines the concept of Preserving vs. Non-Preserving allocations. A Preserving allocation sets the fields in outgoing IP header correctly, and also relays ICMP messages, while a Non-Preserving allocation may not relay correctly in every case. The relaying rules for a Preserving are designed to guarantee the following: o Path MTU Discovery works end-to-end (i.e. client-to-peer), using either the old algorithm ([RFC1191] and [RFC1981]) or the new one Rosenberg, et al. Expires December 26, 2008 [Page 11] Internet-Draft TURN June 2008 ([RFC4821]); o ECN and Diff-Serv works end-to-end; o Loops are prevented by copying and decrementing the TTL/Hop Count field. If the client knows its application or usage scenario requires a Preserving allocation, then it can request one in its Allocate request. If the server is unable to grant this request, then it rejects the Allocate request. Note that a Preserving allocation only makes sense when the transport protocol to the client is UDP; when the transport is TCP or TLS, the allocation is always Non-Preserving. 3. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Readers are expected to be familar with [I-D.ietf-behave-rfc3489bis] and the terms defined there. The following terms are used in this document: TURN: A protocol spoken between a TURN client and a TURN server. It is an extension to the STUN protocol [I-D.ietf-behave-rfc3489bis]. The protocol allows a client to allocate and use a relayed transport address. TURN client: A STUN client that implements this specification. TURN server: A STUN server that implements this specification. It relays data between a TURN client and its peer(s). Peer: A host with which the TURN client wishes to communicate. The TURN server relays traffic between the TURN client and its peer(s). The peer does not interact with the TURN server using the protocol defined in this document; rather, the peer receives data sent by the TURN server and the peer sends data towards the TURN server. Rosenberg, et al. Expires December 26, 2008 [Page 12] Internet-Draft TURN June 2008 Host Transport Address: A transport address allocated on a host. Server-Reflexive Transport Address: A transport address on the "public side" of a NAT. This address is allocated by the NAT to correspond to a specific host transport address. Relayed Transport Address: A transport address that exists on a TURN server. If a permission exists, packets that arrive at this address are relayed towards the TURN client. Allocation: The relayed transport address granted to a client through an Allocate request, along with related state, such as permissions and expiration timers. 5-tuple: The combination (client IP address and port, server IP address and port, and transport protocol (UDP or TCP)) used to communicate between the client and the server . The 5-tuple uniquely identifies this communication stream. The 5-tuple also uniquely identifies the Allocation on the server. Permission: The IP address and transport protocol (but not the port) of a peer that is permitted to send traffic to the TURN server and have that traffic relayed to the TURN client. The TURN server will only forward traffic to its client from peers that match an existing permission. Preserving Allocation An allocation that sets the the fields in the IP header in a specific manner when relaying application data, and which also relays ICMP messages. An allocation that may not do this in some cases is called a Non-Preserving allocation. 4. General Behavior This section contains general TURN processing rules that apply to all TURN messages. TURN is an extension to STUN. All TURN messages, with the exception of the ChannelData message, are STUN-formatted messages. All the base processing rules described in [I-D.ietf-behave-rfc3489bis] apply to STUN-formatted messages. This means that all the message-forming and -processing descriptions in this document are implicitly prefixed with the rules of [I-D.ietf-behave-rfc3489bis]. In addition, the server SHOULD require that all TURN requests use the Long-Term Credential mechanism described in [I-D.ietf-behave-rfc3489bis], and the client MUST be prepared to authenticate requests if required. The server's administrator MUST Rosenberg, et al. Expires December 26, 2008 [Page 13] Internet-Draft TURN June 2008 choose a realm value that will uniquely identify the username and password combination that the client must use, even if the client uses multiple servers under different administrations. The server's administrator MAY choose to allocate a unique username to each client, or MAY choose to allocate the same username to more than one client (for example, to all clients from the same department or company). The client and/or the server MAY include the FINGERPRINT attribute in any of the methods defined in this document. However, TURN does not use the backwards-compatibility mechanism described in [I-D.ietf-behave-rfc3489bis]. By default, TURN runs on the same port as STUN. However, either the SRV procedures or the ALTERNATE-SERVER procedures described in Section 6 may be used to run TURN on a different port. 5. Allocations All TURN operations revolve around allocations, and all TURN messages are associated with an allocation. An allocation conceptually consists of the following state data: o the relayed transport address o The 5-tuple: client IP address, client port, server IP address, server port, transport protocol o the username o the transaction ID of the Allocate request o the time-to-expiry o A list of permissions o A list of channel to peer bindings o A flag indicating whether or not the allocation is Preserving The relayed transport address is the transport address allocated by the server for communicating with peers, while the 5-tuple describes the communication path between the client and the server. Both of these MUST be unique across all allocations, so either one can be used to uniquely identify the allocation. When a TURN message arrives at the server from the client, the server Rosenberg, et al. Expires December 26, 2008 [Page 14] Internet-Draft TURN June 2008 uses the 5-tuple in the message to identify the associated allocation. For all TURN messages (including ChannelData) EXCEPT an Allocate request, if the 5-tuple does not identify an existing allocation, then the message MUST either be rejected with a 437 Allocation Mismatch error (if it is a request), or silently ignored (if it is an indication or a ChannelData message). A client receiving a 437 error response to a request other than Allocate MUST assume the allocation no longer exists. The username and password of the allocation is the username and password of the authenticated Allocate request that creates the allocation. Subsequent requests on an allocation use the same username and password as those used to create the allocation, to prevent attackers from hijacking the client's allocation. Specifically, if the server requires the use of the Long-Term Credential mechanism, and if a non-Allocate request passes authentication under this mechanism, and if the 5-tuple identifies an existing allocation, but the request does not use the same username as used to create the allocation, then the request MUST be rejected with a 438 (Wrong Credentials) error. The transaction ID of the allocation is the transaction ID used in the Allocate request. This is used to detect retransmissions of the Allocate request over UDP (see Section 6.2 for details). The time-to-expiry is the time in seconds left until the allocation expires. Each Allocate or Refresh transaction sets this timer, which then ticks down towards 0. By default, each Allocate or Refresh transaction resets this timer to 600 seconds (10 minutes), but the client can request a different value in the Allocate and Refresh request. Allocations can only be refreshed using the Refresh request; sending data to a peer does not refresh an allocation. When an allocation expires, the state data associated with the allocation is freed. However the server MUST ensure that neither the relayed transport address nor the client reflexive transport address from the 5-tuple are re-used in other allocations until 2 minutes after the allocation expires; this ensures that any messages that are in transit when the allocation expires are gone before either of these transport addresses are re-used. The list of permissions is described in Section 8 and the list of channels is described in Section 10. The differences between a Preserving and a Non-Preserving allocation are described in Section 11. Rosenberg, et al. Expires December 26, 2008 [Page 15] Internet-Draft TURN June 2008 6. Creating an Allocation An allocation on the server is created using an Allocate transaction. 6.1. Sending an Allocate Request The client forms an Allocate request as follows. The client first needs to pick a host transport address that the server does not think is currently in use, or was recently in use. The client SHOULD pick a currently-unused transport address on the client's host (typically by allowing its OS to pick a currently- unused port for a new socket). The client needs to pick a transport protocol to use between the client and the server. The transport protocol MUST be one of UDP, TCP, or TLS over TCP. Since this specification only allows UDP between the server and the peers, it is RECOMMENDED that the client pick UDP unless it has a reason to use a different transport. One reason to pick a different transport would be that the client believes, either through configuration or by experiment, that it is unable to contact any TURN server using UDP. See Section 2.1 for more discussion. The client must also pick a server transport address. Typically, this is done by the client learning (perhaps through configuration) one or more domain names for TURN servers. In this case, the client uses the DNS procedures described in [I-D.ietf-behave-rfc3489bis], but using an SRV service name of "turn" (or "turns" for TURN over TLS) instead of "stun" (or "stuns"). For example, to find servers in the example.com domain, the client performs a lookup for '_turn._udp.example.com', '_turn._tcp.example.com', and '_turns._tcp.example.com' if the client wants to communicate with the server using UDP, TCP, or TLS over TCP, respectively. The client MUST include a REQUESTED-TRANSPORT attribute in the request. This attribute specifies the transport protocol between the server and the peers (note that this is NOT the transport protocol that appears in the 5-tuple). In this specification, the REQUESTED- TRANSPORT type is always UDP. This attribute is included to allow future extensions specify other protocols (e.g., [I-D.ietf-behave-turn-tcp]). If the client wishes the server to initialize the time-to-expire field of the allocation to some value other the default lifetime, then it MAY include a LIFETIME attribute specifying its desired value. This is just a request, and the server may elect to use a different value. Note that the server will ignore requests to Rosenberg, et al. Expires December 26, 2008 [Page 16] Internet-Draft TURN June 2008 initialize the field to less tha the default value. If the client required the allocation to satisfy certain properties, then the client includes the REQUESTED-PROPS attribute. This attribute is optional, and can be omitted if no special properties are required. Using the E and R bits in the REQUESTED-PROPS attribute, the client can request: o (E=1, R=0 ) That the server allocate a relayed transport address with an even port number; OR o (E=1, R=1) That the server reserve a pair of relayed transport addresses with adjacent port numbers N and N+1, where N is even and N+1 is odd, and then use port N for the current allocation. In this case, the server returns a RESERVATION-TOKEN attribute in the response which the client can then include in a subsequent Allocate request to create an allocation with port number N+1. Note that the client cannot request a pair of adjacent ports unless it also requests that the lower numbered port be even. Thus the combination (E=0, R=1) is not allowed. Similarly, by setting the P bit to 1 in the REQUESTED-PROPS attribute, the client can request that the server allocate a Preserving allocation. For all the various REQUESTED-PROPS flags, if the server cannot satisfy the request, the Allocate request is rejected. The client MAY also include a RESERVATION-TOKEN attribute in the request to ask the server to use a previously reserved port for the allocation. If the RESERVATION-TOKEN attribute is included, then the client MUST either omit the REQUESTED-PROPS attribute or set E=0 and R=0, since doing otherwise would make no sense. Once constructed, the client sends the Allocate request on the 5-tuple. 6.2. Receiving an Allocate Request When the server receives an Allocate request, it performs the following checks: 1. The server checks the credentials of the request, as per the Long-Term Credential mechanism of [I-D.ietf-behave-rfc3489bis]. Rosenberg, et al. Expires December 26, 2008 [Page 17] Internet-Draft TURN June 2008 2. The server checks if the 5-tuple is currently in use by an existing allocation, or was it in use by another allocation within the last 2 minutes. If yes, then there are two sub-cases: * If the transport protocol in the 5-tuple is UDP, and if the 5-tuple is currently in use by an existing allocation, and if the transaction id of the request matches the transaction id stored with the allocation, then the request is a retransmission of the original request. The server replies either with a stored copy of the original response, or with a response rebuilt from the stored state data. If the server chooses to rebuild the response, then (a) it need not parse the request further, but can immediately start building a success response, (b) the value of the LIFETIME attribute can be set to the current value of the time-to-expire timer, and (c) the server may need to include an extra field in the allocation to store the token returned in a RESERVATION-TOKEN attribute. * Otherwise, the server rejects the request with a 437 (Allocation Mismatch) error. NOTE: If the request includes credentials that are acceptable to server, but the 5-tuple is already in use, then it is important that the server reject the request with a 437 (Allocation Mismatch) error rather than a 401 (Unauthorized) error. This ensures that the client knows that the problem is with the 5-tuple, rather than (wrongly) believing that the problem lies with its credentials. 3. The server checks if the request contain a REQUESTED-TRANPORT attribute. If the REQUESTED-TRANSPORT attribute is not included or is malformed, the server rejects the request with a 400 (Bad Request) error. Otherwise, if the attribute is included but specifies a protocol other that UDP, the server rejects the request with a 422 (Unsupported Transport Protocol) error. 4. The server checks if the request contains a REQUESTED-PROPS attribute. If yes, then the server checks that it understands and can satisfy all the flags that are set to 1. If a flag is not understood, or if the server cannot satisfy the request, then the server rejects the request with a 508 (Insufficient Port Capacity) error. Note that the combination (E=0, R=1) MUST be treated as unsupported. 5. The server checks if the request contains a RESERVATION-TOKEN attribute. If yes, and the request also contains a REQUESTED- PROPS attribute, then the server rejectes the request with a 400 Rosenberg, et al. Expires December 26, 2008 [Page 18] Internet-Draft TURN June 2008 (Bad Request) error. Otherwise it checks to see if the token is valid (i.e., the token is in range and has not expired, and the corresponding relayed transport address is still available). If the token is not valid for some reason, the server rejects the request with a 508 (Insufficient Port Capacity) error. 6. At any point, the server MAY also choose to reject the request with a 486 (Allocation Quota Reached) error if it feels the client is trying to exceed some locally-defined allocation quota. The server is free to define this allocation quota any way it wishes, but SHOULD define it based on the username used to authenticate the request, and not on the client's transport address. If the server rejects the request with one of the error codes 422 (Unsupported Transport Protocol), 486 (Allocation Quota Reached) or 508 (Insufficient Port Capacity), it MAY include an ALTERNATE-SERVER attribute in the error response redirecting the client to another server that it believes will accept the request. If the attribute is included, the address MUST be from the same address family as the server's transport address. Note that, if the attribute is included, the client will try this alternate server before trying the other servers given by the SRV procedures. If all the checks pass, the server creates the allocation. The 5-tuple is set to the 5-tuple from the Allocate request, while the list of permissions and the list of channels are initially empty. When allocating a relayed transport address for the allocation, the server MUST allocate an IP address from the same family (e.g, IPv4 vs. IPv6) as that on which the request was received (i.e., the server's IP address in the 5-tuple for the allocation). NOTE: An extension to TURN to allow an address from a different address family is currently in progress [I-D.ietf-behave-turn-ipv6]. In addition, the server SHOULD only allocate ports from the range 49152 - 65535 (the Dynamic and/or Private Port range [Port-Numbers]), unless the TURN server application knows, through some means not specified here, that other applications running on the same host as the TURN server application will not be impacted by allocating ports outside this range. This condition can often be satisfied by running the TURN server application on a dedicated machine and/or by arranging that any other applications on the machine allocate ports before the TURN server application starts. In any case, the TURN server SHOULD NOT allocate ports in the range 0 - 1023 (the Well- Known Port range) to discourage clients from using TURN to run Rosenberg, et al. Expires December 26, 2008 [Page 19] Internet-Draft TURN June 2008 standard services. If the request contains a REQUESTED-PROPS attribute with the R flag set, then the server looks for a pair of port numbers N and N+1 on the same IP address, where N is even. Port N is used in the current allocation, while the relayed transport address with port N+1 is assigned a token and reserved for a future allocation. The server MUST hold this reservation for at least 30 seconds, and MAY choose to hold longer (e.g. until the allocation with port N expires). The server then includes the token in a RESERVATION-TOKEN attribute in the success response. If the request contains a RESERVATION-TOKEN, the server uses the previously-reserved transport address corresponding to the included token (if it is still available). The server determines the initial value of the time-to-expire field as follows. If the request contains a LIFETIME attribute, and the proposed lifetime value is greater than the default lifetime, and the proposed lifetime value is otherwise acceptable to the server, then the server uses that value. Otherwise, the server uses the default value. It is RECOMMENDED that the server impose a maximum lifetime of no more than 3600 seconds (1 hour). NOTE: The time-to-expire is recomputed with each successful Refresh request. Thus the value computed here applies only until the first refresh. Once the allocation is created, the server replies with a success response. The success response contains: o A RELAYED-ADDRESS attribute containing the relayed transport address; o A LIFETIME attribute containing the current value of the time-to- expire timer; o A RESERVATION-TOKEN attribute (if a second relayed transport address was reserved). o An XOR-MAPPED-ADDRESS attribute containing the client's IP address and port (from the 5-tuple); NOTE: The XOR-MAPPED-ADDRESS attribute is included in the response as a convenience to the client. TURN itself does not make use of this value, but clients running ICE can often need this value and can thus avoid having to do an extra Binding transaction with some STUN server to learn it. Rosenberg, et al. Expires December 26, 2008 [Page 20] Internet-Draft TURN June 2008 The response (either success or error) is sent back to the client on the 5-tuple. 6.3. Receiving an Allocate Response If the client receives a success response, then it MUST check that the relayed transport address is in an address family that the client understands and is prepared to deal with. This specification only covers the case where the relayed transport address is of the same address family as the client's transport address. If the relayed transport address is not in an address family that the client is prepared to deal with, then the client MUST delete the allocation (Section 7) and MUST NOT attempt to create another allocation on that server until it believes the mismatch has been fixed. The IETF is currently considering mechanisms for transitioning between IPv4 and IPv6 that could result in a client originating an Allocate request over IPv4, but the request would arrive at the server over IPv6, or vica-versa. Hence the importance of this check. Otherwise, the client creates its own copy of the allocation data structure to track what is happening on the server. In particular, the client needs to remember the actual lifetime received back from the server, rather than the value sent to the server in the request. The client must also remember the 5-tuple used for the request and the username and password it used to authenticate the request to ensure that it reuses them for subsequent messages. The client also needs to track the channels and permissions it establishes on the server. The client will probably wish to send the relayed transport address to peers (using some method not specified here) so the peers can communicate with it. The client may also wish to use the server- reflexive address it receives in the XOR-MAPPED-ADDRESS attribute in its ICE processing. If the client receives an error response, then the processing depends on the actual error code returned: o (Request timed out): There is either a problem with the server, or a problem reaching the server with the chosen transport. The client MAY choose to try again using a different transport (e.g., TCP instead of UDP), or the client MAY try a different server. o 400 (Bad Request): The server believes the client's request is malformed for some reason. The client MAY notify the user or operator and SHOULD NOT retry the same request with this server Rosenberg, et al. Expires December 26, 2008 [Page 21] Internet-Draft TURN June 2008 until it believes the problem has been fixed. The client MAY try a different server. o 401 (Unauthorized): If the client has followed the procedures of the Long-Term Credential mechanism and still gets this error, then the server is not accepting the client's credentials. The client SHOULD notify the user or operator and SHOULD NOT send any further requests to this server until it believes the problem has been fixed. The client MAY try a different server. o 437 (Allocation Mismatch): This indicates that the client has picked a 5-tuple which the server sees as already in use or which was recently in use. One way this could happen is if an intervening NAT assigned a mapped transport address that was recently used by another allocation. The client SHOULD pick another client transport address and retry the Allocate request (using a different transaction id). The client SHOULD try three different client transport addresses before giving up on this server. Once the client gives up on the server, it SHOULD NOT try to create another allocation on the server for 2 minutes. o 438 (Wrong Credentials): The client should not receive this error in response to a Allocate request. The client MAY notify the user or operator and SHOULD NOT retry the same request with this server until it believes the problem has been fixed. The client MAY try a different server. o 442 (Unsupported Transport Address): The client should not receive this error in response to a request for a UDP allocation. The client MAY notify the user or operator and SHOULD NOT retry the same request with this server until it believes the problem has been fixed. The client MAY try a different server. o 486 (Allocation Quota Reached): The server is currently unable to create any more allocations with this username. The client SHOULD wait at least 1 minute before trying to create any more allocations on the server. The client MAY try a different server. o 508 (Insufficient Port Capacity): The server has no more relayed transport addresses avaiable, or has none with the requested properties, or the one that was reserved is no longer available. If the client is using either the REQUESTED-PROPS or the RESERVATION-TOKEN attribute, then the client MAY choose to remove this attribute and try again immediately. Otherwise, the client SHOULD wait at least 1 minute before trying to create any more allocations on this server. The client MAY try a different server. Rosenberg, et al. Expires December 26, 2008 [Page 22] Internet-Draft TURN June 2008 If the error response contains an ALTERNATE-SERVER attribute, and the client elects to try a different server, the the client SHOULD try the alternate server specified in that attribute (while obeying the rules in [I-D.ietf-behave-rfc3489bis] for avoiding redirection loops) before trying any other servers found using the SRV procedures of [I-D.ietf-behave-rfc3489bis]. 7. Refreshing an Allocation A Refresh transaction can be used to either (a) refresh an existing allocation and update its time-to-expire, or (b) delete an existing allocation. If a client wishes to continue using an allocation, then the client MUST refresh it before it expires. It is suggested that the client refresh the allocation roughly 1 minute before it expires. If a client no longer wishes to use an allocation, then it SHOULD explicitly delete the allocation. A client MAY also change the time- to-expire of an allocation at any time for other reasons. 7.1. Sending a Refresh Request If the client wishes to immediately delete an existing allocation, it includes a LIFETIME attribute with a value of 0. All other forms of the request refresh the allocation. The Refresh transaction updates the time-to-expire timer of an allocation. If the client wishes the server to set the time-to- expire timer to something other than the default lifetime, it includes a LIFETIME attribute with the requested value. The server then computes a new time-to-expire value in the same way as it does for an Allocate transaction, with the exception that a requested lifetime of 0 causes the server to immediately delete the allocation. The Refresh transaction is sent on the 5-tuple for the allocation. 7.2. Receiving a Refresh Request When the server receives a Refresh request, it processes it as follows. If, during processing, an error in the request is detected (for example, a syntax error in the request which causes a 400 error), then the request is rejected with an error response but the allocation is NOT deleted (but note that a 437 error will indicate that the allocation was not found). The server determines the new value for the time-to-expire field as follows. If the request contains a LIFETIME attribute, and the Rosenberg, et al. Expires December 26, 2008 [Page 23] Internet-Draft TURN June 2008 attribute value is 0, then the server uses a value of 0, which causes the allocation to expire. Otherwise, if the request contains a LIFETIME attribute and the attribute value is greater than the default lifetime, and the attribute value is otherwise acceptable to the server, then the server uses the attribute value. Otherwise, the server uses the default value. It is RECOMMENDED that the server impose a maximum lifetime of no more than 3600 seconds (1 hour). The server then constructs a success response containing: o A LIFETIME attribute containing the current value of the time-to- expire timer. The response is then sent on the 5-tuple. 7.3. Receiving a Refresh Response If the client receives a success response to its Refresh request, it updates its copy of the allocation data structure with the time-to- expire value contained in the response. If the client receives an 437 (Allocation Mismatch) error response to its Refresh request, then it must consider the allocation as having expired, as described in Section 4. All other errors indicate a software error on the part of either the client or the server. 8. Permissions For each allocation, the server keeps a list of zero or more permissions. Each permission consists an IP address which uniquely identifies the permission, and an associated time-to-expiry. The IP address describes a peer that is allowed to send data to the client, and the time-to-expiry is the number of seconds until the permission expires. Various events, as described in subsequent sections, can cause a permission for a given IP address to be installed or refreshed. This causes one of two things to happen: o If no permission for that IP address exists, then a permission is created with the given IP address and a time-to-expiry equal to the default permission lifetime. o If a permission for that IP address already exists, then the lifetime for that permission is reset to the default permission lifetime. Rosenberg, et al. Expires December 26, 2008 [Page 24] Internet-Draft TURN June 2008 The default permission lifetime MUST be 300 seconds (= 5 minutes). Each permission's time-to-expire decreases down once per second until it reaches 0, at which point the permission expires and is deleted. When a UDP datagram arrives at the relayed transport address for the allocation, the server checks the list of permissions for that allocation. If there is a permission with an IP address that is equal to the source IP address of the UDP datagram, then the UDP datagram can be relayed to the client. Otherwise, the UDP datagram is silently discarded. Note that only IP addresses are compared; port numbers are irrelevant. The permissions for one allocation are totally unrelated to the permissions for a different allocation. If an allocation expires, all its permissions expire with it. NOTE: Though TURN permissions expire after 5 minutes, many NATs deployed at the time of publication expire their UDP bindings considerably faster. Thus an application using TURN will probably wish to send some sort of keep-alive traffic at a much faster rate. Applications using ICE should follow the keep-alive guidelines of ICE [I-D.ietf-mmusic-ice], and applications not using ICE are advised to do something similar. 9. Send and Data Indications TURN supports two ways to send and receive data from peers. This section describes the use of Send and Data indications, while Section 10 describes the use of the Channel Mechanism. 9.1. Sending a Send Indication A client can use a Send Indication to pass data to the server for relaying to a peer. A client can also use a Send Indication without a DATA attribute to install or refresh a permission for the specified IP address. A client may use a Send indication to send data to a peer even if a channel is bound to that peer. When forming a Send Indication, the client MUST include a PEER- ADDRESS attribute and MAY include a DATA attribute. If the DATA attribute is included, then the DATA attribute contains the actual application data to be sent to the peer, and the PEER-ADDRESS attribute contains the transport address of the peer to which the data is to be sent. If the DATA attribute is not present, then the PEER-ADDRESS attribute contains the IP address for which a permission is to be installed or refreshed; in this case the port specified in Rosenberg, et al. Expires December 26, 2008 [Page 25] Internet-Draft TURN June 2008 the attribute is ignored. Note that no authentication attributes are included, since indications cannot be authenticated using the Long-Term Credential mechanism. The Send Indication MUST be sent using the same 5-tuple used for the original allocation. 9.2. Receiving a Send Indication When the server receives a Send indication, it processes it as follows. If the received Send indication contains a DATA attribute, then it forms a UDP datagram as follows: o the source transport address is the relayed transport address of the allocation, where the allocation is determined by the 5-tuple on which the Send Indication arrived; o the destination transport address is taken from the PEER-ADDRESS attribute; o the data following the UDP header is the contents of the value field of the DATA attribute. The resulting UDP datagram is then sent to the peer. If any errors are detected during this process (e.g., the Send indication does not contain a PEER-ADDRESS attribute), the received indication is silently discarded and no UDP datagram is sent. When the server receives a valid Send Indication, either with or without a DATA attribute, it also installs or refreshes a permission for the IP address contained in the PEER-ADDRESS attribute (see Section 8). 9.3. Receiving a UDP Datagram When the server receives a UDP datagram at a currently allocated relayed transport address, the server looks up the allocation associated with the relayed transport address. It then checks to see if relaying is permitted, as described in section Section 8). If relaying is permitted, and there is no channel bound to the peer that sent the UDP datagram (see ISection 10), then the server forms and sends a Data indication. The Data indication MUST contain both a PEER-ADDRESS and a DATA attribute. The DATA attribute is set to the Rosenberg, et al. Expires December 26, 2008 [Page 26] Internet-Draft TURN June 2008 value of the 'data octets' field from the datagram, and the PEER- ADDRESS attribute is set to the source transport address of the received UDP datagram. The Data indication is then sent on the 5-tuple associated with the allocation. 9.4. Receiving a Data Indication When the client receives a Data indication, it checks that the Data indication contains both a PEER-ADDRESS and a DATA attribute. It then delivers the data octets inside the DATA attribute to the application, along with an indication that they were received from the peer whose transport address is given by the PEER-ADDRESS attribute. 10. Channels Channels provide a way for the client and server to send application data using ChannelData messages, which have less overhead than Send and Data indications. Channel bindings are always initiated by the client. The client can bind a channel to a peer at any time during the lifetime of the allocation. The client may bind a channel to a peer before exchanging data with it, or after exchanging data with it (using Send and Data indications) for some time, or may choose never to bind a channel it. The client can also bind channels to some peers while not binding channels to other peers. Channel bindings are specific to an allocation, so that a binding in one allocation has no relationship to a binding in any other allocation. If an allocation expires, all its channel bindings expire with it. A channel binding consists of: o A channel number; o A transport address (of the peer); o A time-to-expiry timer. Within the context of an allocation, a channel binding is uniquely identified either by the channel number or by the transport address. Thus the same channel cannot be bound to two different transport addresses, nor can the same transport address be bound to two different channels. Rosenberg, et al. Expires December 26, 2008 [Page 27] Internet-Draft TURN June 2008 A channel binding last for 10 minutes unless refreshed. Refreshing the binding (by the server receiving either a ChannelBind request rebinding the channel to the same peer, or by the server receiving a ChannelData message on that channel) resets the time-to-expire timer back to 10 minutes. When the channel binding expires, the channel becomes unbound and available for binding to a different transport address. When binding a channel to a peer, the client SHOULD be prepared to receive ChannelData messages on the channel from the server as soon as it has sent the ChannelBind request. Over UDP, it is possible for the client to receive ChannelData messages from the server before it receives a ChannelBind success response. In the other direction, the client MAY elect to send ChannelData messages before receiving the ChannelBind success response. Doing so, however, runs the risk of having the ChannelData messages dropped by the server if the ChannelBind request does not succeed for some reason (e.g., packet lost if the request is sent over UDP, or the server being unable to fulfill the request). A client that wishes to be safe should either queue the data, or use Send indications until the channel binding is confirmed. 10.1. Sending a ChannelBind Request A channel binding is created using a ChannelBind transaction. A channel binding can also be refreshed using a ChannelBind transaction. To initiate the ChannelBind transaction, the client forms a ChannelBind request. The channel to be bound is specified in a CHANNEL-NUMBER attribute, and the peer's transport address is specified in a PEER-ADDRESS attribute. Section 10.2 describes the restrictions on these attributes. Note that rebinding a channel to the same transport address that it is already bound to provides a way to refresh a channel binding without sending data to the peer. Once formed, the ChannelBind Request is sent using the 5-tuple for the allocation. 10.2. Receiving a ChannelBind Request When the server receives a ChannelBind request, it checks the following: Rosenberg, et al. Expires December 26, 2008 [Page 28] Internet-Draft TURN June 2008 o The request contains both a CHANNEL-NUMBER and a PEER-ADDRESS attribute; o The channel number is in the range 0x4000 to 0xFFFE (inclusive); o The channel number is not currently bound to a different transport address (same transport address is OK); o The transport address is not currently bound to a different channel number. If any of these tests fail, the server replies with an error response with error code 400 "Bad Request". Otherwise, the ChannelBind request is valid and the server replies with a ChannelBind success response. If ChannelBind request is valid, then the server creates or refreshes the channel binding using the channel number in the CHANNEL-ADDRESS attribute and the transport address in the PEER-ADDRESS attribute. The server also installs or refreshes a permission for the IP address in the PEER-ADDRESS attribute. 10.3. Receiving a ChannelBind Response When the client receives a successful ChannelBind response, it updates its data structures to record that the channel binding is now active. 10.4. The ChannelData Message The ChannelData message is used to carry application data between the client and the server. It has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Channel Number | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | / Application Data / / / | | | +-------------------------------+ | | +-------------------------------+ The Channel Number field specifies the number of the channel on which the data is traveling, and thus the address of the peer that is Rosenberg, et al. Expires December 26, 2008 [Page 29] Internet-Draft TURN June 2008 sending or is to receive the data. The channel number MUST be in the range 0x4000 - 0xFFFF, with channel number 0xFFFF being reserved for possible future extensions. Channel numbers 0x0000 - 0x3FFF cannot be used because bits 0 and 1 are used to distinguish ChannelData messages from STUN-formatted messages (i.e., Allocate, Send, Data, ChannelBind, etc). STUN- formatted messages always have bits 0 and 1 as "00", while ChannelData messages use combinations "01", "10", and "11". The Length field specifies the length in bytes of the application data field (i.e., it does not include the size of the ChannelData header). Note that 0 is a valid length. The Application Data field carries the data the client is trying to send to the peer, or that the peer is sending to the client. 10.5. Sending a ChannelData Message Once a client has bound a channel to a peer, then when the client has data to send to that peer it may use either a ChannelData message or a Send Indication; that is, the client is not obligated to use the channel when it exists and may freely intermix the two message types when sending data to the peer. The server, on the other hand, MUST use the ChannelData message if a channel has been bound to the peer. The fields of the ChannelData message are filled in as described in Section 10.4. Over stream transports, the ChannelData message MUST be padded to a multiple of four bytes in order to ensure the alignment of subsequent messages. The padding is not reflected in the length field of the ChannelData message, so the actual size of a ChannelData message (including padding) is (4 + Length) rounded up to the nearest multiple of 4. Over UDP, the padding is not required but MAY be included. The ChannelData message is then sent on the 5-tuple associated with the allocation. 10.6. Receiving a ChannelData Message The receiver of the ChannelData message uses bits 0 and 1 to distinguish it from STUN-formatted messages, as described in Section 10.4. If the ChannelData message is received in a UDP datagram, and if the UDP datagram is too short to contain the claimed length of the Rosenberg, et al. Expires December 26, 2008 [Page 30] Internet-Draft TURN June 2008 ChannelData message (i.e., the UDP header length field value is less than the ChannelData header length field value + 4 + 8), then the message is silently discarded. If the ChannelData message is received over TCP or over TLS over TCP, then the actual length of the ChannelData message is as described in Section 10.5. If the ChannelData message is received on a channel which is not bound to any peer, then the message is silently discarded. 10.7. Relaying When a server receives a ChannelData message, it first processes it as described in the previous section. If no errors are detected, it relays the application data to the peer by forming a UDP datagram as follows: o the source transport address is the relayed transport address of the allocation, where the allocation is determined by the 5-tuple on which the ChannelData message arrived; o the destination transport address is the transport address to which the channel is bound; o the data following the UDP header is the contents of the data field of the ChannelData message. The resulting UDP datagram is then sent to the peer. If the ChannelData message is valid, then the server refreshes the channel binding, and also installs or refreshes a permission for the IP address part of the transport address to which the UDP datagram is sent (see Section 8). In the other direction, when the server receives a UDP datagram on the relayed transport address associated with an allocation, then it first checks to see if it is permitted to relay the datagram. This check is done as described in Section 8. If relaying is permitted, then the server checks to see if there is a channel bound to the peer that sent the UDP datagram. If there is, then it SHOULD form and send a ChannelData message as described in Section 10.5. If no channel is bound to the peer, then it MUST form and send a Data indication as described in Section 9.3. Rosenberg, et al. Expires December 26, 2008 [Page 31] Internet-Draft TURN June 2008 11. IP and ICMP This section describes how the server sets various fields in the IP header when relaying between the client and the peer or vica-versa. It also describes how the server relays ICMP messages. The descriptions in this section apply: (a) when the server receives a Send indication or ChannelData message from the client and sends a UDP datagram to the peer, (b) when the server receives a UDP datagram on the relayed-transport address and sends a Data indication or ChannelData message to the client, or (c) when the server receives an ICMP message. This section does not apply when the server sends TURN control messages. The descriptions below have two parts: a preferred behavior and an alternate behavior. A Preserving allocation MUST implement the preferred behavior. A non-preserving allocation with UDP transport to the client SHOULD implement the preferred behavior, but if that is not possible for a particular field, then it SHOULD implement the alternative behavior. A non-preserving allocation with TCP or TLS transport to client SHOULD implement the alternate behavior, except where this conflicts with standard TCP or TLS behavior. 11.1. IP This section describes the preferred and alternate behavior for various fields in the IP header. Time to Live (IPv4) or Hop Count (IPv6) Preferred Behavior: If the incoming value is 0, then send an ICMP Time Exceeded message back to the sender. Otherwise set the outgoing Time to Live/Hop Count to one less than the incoming value. Alternate Behavior: Set the outgoing value to the default for outgoing packets. Diff-Serv Code Point Preferred Behavior: Set the outgoing value to the incoming value, unless the server, though configuration or other means, believes that a different setting is more appropriate. Alternate Behavior: Set the outgoing value to Best Effort, unless the server, through configuration or other means, believes a different setting is more appropriate. Rosenberg, et al. Expires December 26, 2008 [Page 32] Internet-Draft TURN June 2008 ECN Preferred Behavior: Set the outgoing value to the incoming value, UNLESS the server is doing Active Queue Management, the incoming ECN field is 01 or 10, and the server wishes to indicate that congestion has been experienced, in which case set the outgoing value to 11. Alternate Behavior: Set the outgoing value to 00 (ECN not supported) Flow Label Preferred Behavior: Set the outgoing flow label to 0. Alternate Behavior: Same as the Preferred behavior. IPv4 Fragmentation Preferred Behavior: If the outgoing packet size does not exceed the outgoing link's MTU, then send the outgoing packet unfragmented. Set the DF bit in the outgoing packet to the value of the DF bit in the incoming packet, and set the other fragmentation fields (Identification, MF, Fragment Offset) as appropriate for a packet originating from the server. Otherwise, if the outgoing link's MTU is exceeded and the incoming DF bit is 0, then fragment the packet before sending. Set the outgoing DF to 0, and set the other fragmentation fields as appropriate for fragments originated from the server. Otherwise [link MTU exceeded and incoming DF set], drop the outgoing packet and send an ICMP message of type 3 code 4 ("fragmentation needed and DF set") to the sender of the incoming packet. Alternate Behavior: As described in the Preferred Behavior, except always assume the incoming DF bit is 0. IPv6 Fragmentation Preferred Behavior: Rosenberg, et al. Expires December 26, 2008 [Page 33] Internet-Draft TURN June 2008 If the incoming packet did not include a Fragmentation header and the outgoing packet size does not exceed the outgoing link's MTU, then send the outgoing packet without a Fragmentation header. If the incoming packet included a Fragment header and if the outgoing packet size (with a Fragmentation header included) does not exceed the outgoing link's MTU, then send the outgoing packet with a Fragmentation header. Set the fields of the Fragmentation header as appropriate for a packet originating from the server. If the incoming packet did not include a Fragmentation header and the outgoing packet size exceeds the outgoing link's MTU , then drop the outgoing packet and send an ICMP message of type 2 code 0 ("Packet too big") to the sender of the incoming packet. If the packet is being sent to the peer, then reduce the MTU reported in the ICMP message by 48 bytes to allow room for the overhead of a Data indication. Otherwise, if the link's MTU is exceeded and the incoming packet contained a Fragmentation header, then fragment the outgoing packet into fragments of no more than 1280 bytes. Set the fields of the Fragmentation header as appropriate for a packet originating from the server. Alternate Behavior: As described in the Preferred Behavior, except always assume incoming packet has a Fragmentation header. IPv4 Options Preferred Behavior: The outgoing packet is sent without any IPv4 options. Alternate Behavior: Same as preferred. IPv6 Extention Headers Preferred Behavior: The outgoing packet is sent without any IPv6 extension headers, with the exception of the Fragmentation header as described above Alternate Behavior: Same as preferred. Rosenberg, et al. Expires December 26, 2008 [Page 34] Internet-Draft TURN June 2008 11.2. ICMP This sub-section describes the preferred behavior of ICMP relaying. The corresponding alternate behavior is to not relay ICMP messages. When an ICMP message arrives at the server, the copy of the original IP packet present inside the ICMP message is examined. The server first checks that the original IP packet header is immediately followed by a UDP protocol header, such that the original source transport address was X and the original destination transport address was Y. The server also checks that the type and code values in the ICMP header are one of those relayed (see below). Other ICMP messages are either ignored, or used by the server internally in an unspecified manner. The server then checks if one of the following two cases applies: Case 1: X is a relayed-transport-address currently assigned to an active allocation on the server, and there exists a permission for the IP address of Y in the allocation. In this case, the original IP packet was traveling from the server to a peer, so the the server relays the ICMP message back to the client. The server creates a Data indication where the PEER-ADDRESS attribute contains Y, and the ICMP attribute contains the type and code from the incoming ICMP message, and the DATA attribute contains application data from the original IP packet starting AFTER the UDP header. The server SHOULD include as much application data as possible consistent with not exceeding a total IP packet size of either 576 bytes (for IPv4) or 1280 bytes (for IPv6). Note that there is no point in including the original IP or UDP header in the DATA attribute because those headers were generated by the server, not the client. Case 2: There is an active allocation where X is the server transport address, Y is the client transport address, and UDP is used as transport between the client and the server. Furthermore, the packet after the UDP header is either (a) a ChannelData header which contains an active channel number in the allocation, or (b) a Data indication whose PEER-ADDRESS attribute contains an IP address for which there exists a permission in the allocation. In this case, the original IP packet was traveling from the server to the client, so the server creates and sends an ICMP message to the peer. The outgoing ICMP message contains the type and code fields from the incoming ICMP message and then contains an approximation to the original IP packet sent from the peer to the server (the one the Rosenberg, et al. Expires December 26, 2008 [Page 35] Internet-Draft TURN June 2008 server was trying to relay to the client inside the ChannelData or Data indication). This approximation contains a synthesized IP header, a synthesized UDP header, and some application data. The synthesis is done as follows: o The destination transport address is the relayed-transport-address of the allocation; o The source transport address is the peer's transport address determined from either (a) the channel number or (b) the PEER- ADDRESS attribute; o The application data is taken from either (a) the ChannelData message or (b) the DATA attribute. The server SHOULD include as much application data as possible consistent with not exceeding either 576 bytes (for IPv4) or 1280 bytes (for IPv6). The remaining fields in the IP and UDP headers are simply set to sensible values, since for most of them there is no way to reconstruct the original values. The server SHOULD relay as all ICMP type/code combinations and MUST relay at at least the following combinations. For IPv4: Type 3, code 4: Fragmentation needed and DF set For IPv6: Type 2, code : Packet too big 12. New STUN Methods This section lists the codepoints for the new STUN methods defined in this specification. See elsewhere in this document for the semantics of these new methods. Request/Response Transactions 0x003 : Allocate 0x004 : Refresh 0x009 : ChannelBind Indications 0x006 : Send 0x007 : Data Rosenberg, et al. Expires December 26, 2008 [Page 36] Internet-Draft TURN June 2008 13. New STUN Attributes This STUN extension defines the following new attributes: 0x000C: CHANNEL-NUMBER 0x000D: LIFETIME 0x0010: Reserved (was BANDWIDTH) 0x0012: PEER-ADDRESS 0x0013: DATA 0x0016: RELAY-ADDRESS 0x0018: REQUESTED-PROPS 0x0019: REQUESTED-TRANSPORT 0x0022: RESERVATION-TOKEN 13.1. CHANNEL-NUMBER The CHANNEL-NUMBER attribute contains the number of the channel. It is a 16-bit unsigned integer, followed by a two-octet RFFU (Reserved For Future Use) field which MUST be set to 0 on transmission and MUST be ignored on reception. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Channel Number | RFFU = 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 13.2. LIFETIME The lifetime attribute represents the duration for which the server will maintain an allocation in the absence of a refresh. It is a 32- bit unsigned integral value representing the number of seconds remaining until expiration. 13.3. PEER-ADDRESS The PEER-ADDRESS specifies the address and port of the peer as seen from the TURN server. It is encoded in the same way as XOR-MAPPED- ADDRESS. 13.4. DATA The DATA attribute is present in all Data Indications and most Send Indications. It contains raw payload data that is to be sent (in the case of a Send Request) or was received (in the case of a Data Indication). Rosenberg, et al. Expires December 26, 2008 [Page 37] Internet-Draft TURN June 2008 13.5. RELAY-ADDRESS The RELAY-ADDRESS is present in Allocate responses. It specifies the address and port that the server allocated to the client. It is encoded in the same way as XOR-MAPPED-ADDRESS. 13.6. REQUESTED-PROPS This attribute allows the client to request that the allocation have certain properties. The attribute is 32 bits long. Its format is: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |E|R|P| MUST be 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The first part of the attribute value contains a number of one-bit flags. These are: E: If 1, the port number for the relayed-transport-address must be even. If 0, the port number can be even or odd. R: If 1, the server must reserve the next highest port for a subsequent allocation. If 0, no such reservation is requested. If the client sets the R bit to 1, it MUST also set the E bit to 1 (however, the E bit may be 1 when the R bit is 0). P: If 1, the allocation must be a Preserving allocation. If 0, the allocation can be either Preserving or Non-Preserving. All these flags have the property that if the bit is 1, and the server cannot create an allocation that satisfies the request, then the Allocate request is rejected. To allow future TURN extensions to define new flags that also have this property, the client MUST set the rest of the attribute to zero, and the server MUST fail the Allocate request if any bits which the server does not support are set to 1. By doing this, any new flags that are not recognized by the server will cause the Allocate request to fail. 13.7. REQUESTED-TRANSPORT This attribute is used by the client to request a specific transport protocol for the allocated transport address. It has the following format: Rosenberg, et al. Expires December 26, 2008 [Page 38] Internet-Draft TURN June 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Protocol | RFFU | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Protocol field specifies the desired protocol. The codepoints used in this field are taken from those allowed in the Protocol field in the IPv4 header and the NextHeader field in the IPv6 header [Protocol-Numbers]. This specification only allows the use of codepoint 17 (User Datagram Protocol). The RFFU field MUST be set to zero on transmission and MUST be ignored on receiption. It is reserved for future uses. 13.8. RESERVATION-TOKEN The RESERVATION-TOKEN attribute contains a token that uniquely identifies a relayed transport address being held in reserve by the server. The server includes this attribute in a success response to tell the client about the token, and the client includes this attribute in a subsequent Allocate request to request the server use that relayed transport address for the allocation. The attribute value is a 64-bit-long field containing the token value. 14. New STUN Error Response Codes This document defines the following new error response codes: 437 (Allocation Mismatch): A request was received by the server that requires an allocation to be in place, but there is none, or a request was received which requires no allocation, but there is one. 438 (Wrong Credentials): The credentials in the (non-Allocate) request, though otherwise acceptable to the server, do not match those used to create the allocation. 442 (Unsupported Transport Protocol): The Allocate request asked the server to use a transport protocol between the server and the peer that the server does not support. NOTE: This does NOT refer to the transport protocol used in the 5-tuple. Rosenberg, et al. Expires December 26, 2008 [Page 39] Internet-Draft TURN June 2008 486 (Allocation Quota Reached): No more allocations using this username can be created at the present time. 508 (Insufficient Port Capacity): The server has no more relayed transport addresses available right now, or has none with the requested properties, or the one that corresponds to the specified token is not available. 15. Security Considerations TURN servers allocate resources to clients, in contrast to the Binding method defined in [I-D.ietf-behave-rfc3489bis]. Therefore, a TURN server may require the authentication and authorization of STUN requests. This authentication is provided by mechanisms defined in the STUN specification itself, in particular digest authentication. Because TURN servers allocate resources, they can be susceptible to denial-of-service attacks. All Allocate transactions are authenticated, so that an unknown attacker cannot launch an attack. An authenticated attacker can generate multiple Allocate Requests, however. To prevent a single malicious user from allocating all of the resources on the server, it is RECOMMENDED that a server implement a per user limit on the number of allocations that can active at one time. Such a mechanism does not prevent a large number of malicious users from each requesting a small number of allocations. Attacks such as these are possible using botnets, and are difficult to detect and prevent. Implementors of TURN should keep up with best practices around detection of anomalous botnet attacks. A client will use the transport address learned from the RELAY- ADDRESS attribute of the Allocate Response to tell other users how to reach them. Therefore, a client needs to be certain that this address is valid, and will actually route to them. Such validation occurs through the message integrity checks provided in the Allocate response. They can guarantee the authenticity and integrity of the allocated addresses. Note that TURN is not susceptible to the attacks described in Section 12.2.3, 12.2.4, 12.2.5 or 12.2.6 of [I-D.ietf-behave-rfc3489bis] [[TODO: Update section number references to 3489bis]]. These attacks are based on the fact that a STUN server mirrors the source IP address, which cannot be authenticated. STUN does not use the source address of the Allocate Request in providing the RELAY-ADDRESS, and therefore, those attacks do not apply. TURN attempts to adhere as closely as possible to common firewall policies, consistent with allowing data to flow. TURN has fairly limited applicability, requiring a user to explicitly authorize Rosenberg, et al. Expires December 26, 2008 [Page 40] Internet-Draft TURN June 2008 permission to receive data from a peer, one IP address at a time. Thus, it does not provide a general technique for externalizing sockets. Rather, it has similar security properties to the placement of an address-restricted NAT in the network, allowing messaging in from a peer only if the internal client has sent a packet out towards the IP address of that peer. This limitation means that TURN cannot be used to run, for example, SIP servers, NTP servers, FTP servers or other network servers that service a large number of clients. Rather, it facilitates rendezvous of NATted clients that use some other protocol, such as SIP, to communicate IP addresses and ports for communications. Confidentiality of the transport addresses learned through Allocate transactions does not appear to be that important. If required, it can be provided by running TURN over TLS. TURN does not and cannot guarantee that UDP data is delivered in sequence or to the correct address. As most TURN clients will only communicate with a single peer, the use of a single channel number will be very common. Consider an enterprise where Alice and Bob are involved in separate calls through the enterprise NAT to their corporate TURN server. If the corporate NAT reboots, it is possible that Bob will obtain the exact NAT binding originally used by Alice. If Alice and Bob were using identical channel numbers, Bob will receive unencapsulated data intended for Alice and will send data accidentally to Alice's peer. This is not a problem with TURN. This is precisely what would happen if there was no TURN server and Bob and Alice instead provided a (STUN) reflexive transport address to their peers. If detecting this misdelivery is a problem, the client and its peer need to use message integrity on their data. Relay servers are useful even for users not behind a NAT. They can provide a way for truly anonymous communications. A user can cause a call to have its media routed through a TURN server, so that the user's IP addresses are never revealed. Any relay addresses learned through an Allocate request will not operate properly with IPSec Authentication Header (AH) [RFC4302] in transport or tunnel mode. However, tunnel-mode IPSec ESP [RFC4303] should still operate. 16. IANA Considerations Since TURN is an extension to STUN [I-D.ietf-behave-rfc3489bis], the methods, attributes and error codes defined in this specification are new method, attributes, and error codes for STUN. This section directs IANA to add these new protocol elements to the IANA registry Rosenberg, et al. Expires December 26, 2008 [Page 41] Internet-Draft TURN June 2008 of STUN protocol elements. The codepoints for the new STUN methods defined in this specification are listed in Section 12. The codepoints for the new STUN attributes defined in this specification are listed in Section 13. The codepoints for the new STUN error codes defined in this specification are listed in Section 14. Extensions to TURN can be made through IETF consensus. 17. IAB Considerations The IAB has studied the problem of "Unilateral Self Address Fixing", which is the general process by which a client attempts to determine its address in another realm on the other side of a NAT through a collaborative protocol reflection mechanism [RFC3424]. The TURN extension is an example of a protocol that performs this type of function. The IAB has mandated that any protocols developed for this purpose document a specific set of considerations. TURN is an extension of the STUN protocol. As such, the specific usages of STUN that use the TURN extensions need to specifically address these considerations. Currently the only STUN usage that uses TURN is ICE [I-D.ietf-mmusic-ice]. 18. Example TBD 19. Changes from Previous Versions Note to RFC Editor: Please remove this section prior to publication of this document as an RFC. This section lists the changes between the various versions of this specification. 19.1. Changed from -07 to -08 o Removed the BANDWIDTH attribute and all associated text (including error code 507 "Insufficient Bandwidth Capacity"), as the requirements for this feature were not clear and it was felt the Rosenberg, et al. Expires December 26, 2008 [Page 42] Internet-Draft TURN June 2008 feature could be easily added later. o Changed the format of the REQUESTED-PROPS attribute from a one- byte field to a set of bit flags. Changed the semantics of the unused portion of the value from RFFU to "MUST be 0" to give a more desirable behavior when new flags are defined. o Introduced the concept of Preserving vs. Non-Preserving allocations. As a result, completely revamped the rules for how to set the fields in the IP header, and added rules for relaying ICMP messages when the allocation is Preserving. 19.2. Changes from -06 to -07 o Rewrote the General Behavior section, making various changes in the process. o Changed the usage of authentication from MUST to SHOULD. o Changed the requirement that subsequent requests use the same username and password from MUST to SHOULD to allow for the possibility of changing the credentials using some unspecified mechanism. o Introduced a 438 (Wrong Credentials) error which is used when a non-Allocate request authenticates but does not use the same username and password as the Allocate request. Having a separate error code for this case avoids the client being confused over what the error actually is. o The server must now prevent the relayed transport address and the 5-tuple from being reused in different allocations for 2 minutes after the allocation expires. o Changed the usage of FINGERPRINT from MUST NOT to MAY, to allow for the possible multiplexing of TURN with some other protocol. o Rewrote much of the section on Allocations, splitting it into three new sections (one on allocations in general, one on creating an allocation, and one on refreshing an allocation). o Replaced the mechanism for requesting relayed transport addresses with specific properties. The new mechanism is less powerful: a client can request an even port, or a pair of ports, but cannot request a single odd port or a specific port as was possible under the old mechanism. Nor can the client request a specific IP address. Rosenberg, et al. Expires December 26, 2008 [Page 43] Internet-Draft TURN June 2008 o Changed the rules for handling ALTERNATE-SERVER, removing the requirement that the referring server have "positive knowledge" about the state of the alternate server. The new rules instead rely on text in STUN to prevent referral loops. o Changed the rules for allocation lifetimes. Allocations lifetimes are now a minimum of 10 minutes; the client can ask for longer values, but requests for shorter values are ignored. The text now recommends that the client refresh an allocation one minute before it expires. o Put in temporary procedures for handling the BANDWIDTH attribute, modelled on the LIFETIME attribute. These procedures are mostly placeholders and likely to change in the next revision. o Added a detailed description of how a client reacts to the various errors it can receive in reply to an Allocate request. This replaces the various descriptions that were previously scattered throughout the document, which were inconsistent and sometimes contradictory. o Added a new section that gives the normative rules for permissions. o Changed the rules around permission lifetimes. The text used to recommend a value of one minute; it MUST now be 5 minutes. o Removed the errors "Channel Missing or Invalid", "Peer Address Missing or Invalid" and "Lifetime Malformed or Invalid" and used 400 "Bad Request" instead. o Rewrote portions of the section on Send and Data indications and the section on Channels to try to make the client vs. server behavior clearer. o Channel bindings now expire after 10 minutes, and must be refreshed to keep them alive. o Binding a channel now installs or refreshes a permission for the IP address of corresponding peer. o Changed the wording describing the situation when the client sends a ChannelData message before receiving the ChannelBind success response. -06 said that client SHOULD NOT do this; -07 now says that a client MAY, but describes the consequences of doing it. o Added a section discussing the setting of fields in the IP header. Rosenberg, et al. Expires December 26, 2008 [Page 44] Internet-Draft TURN June 2008 o Replaced the REQUESTED-PORT-PROPS attribute with the REQUESTED- PROPS attribute that has a different format and semantics, but reuses the same code point. o Replaced the REQUESTED-IP attribute with the RESERVATION-TOKEN attribute, which has a different format and semantics, but reuses the same code point. o Removed error codes 443 and 444, and replaced them with 508 (Insufficient Port Capacity). Also changed the error text for code 507 from "Insufficient Capacity" to "Insufficient Bandwidth Capacity". 19.3. Changes from -05 to -06 o Changed the mechanism for allocating channels to the one proposed by Eric Rescorla at the Dec 2007 IETF meeting. o Removed the framing mechanism (which was used to frame all messages) and replaced it with the ChannelData message. As part of this change, noted that the demux of ChannelData messages from TURN messages can be done using the first two bits of the message. o Rewrote the sections on transmitted and receiving data as a result of the above to changes, splitting it into a section on Send and Data Indications and a separate section on channels. o Clarified the handling of Allocate Request messages. In particular, subsequent Allocate Request messages over UDP with the same transaction id are not an error but a retransmission. o Restricted the range of ports available for allocation to the Dynamic and/or Private Port range, and noted when ports outside this range can be used. o Changed the format of the REQUESTED-TRANSPORT attribute. The previous version used 00 for UDP and 01 for TCP; the new version uses protocol numbers from the IANA protocol number registry. The format of the attribute also changed. o Made a large number of changes to the non-normative portion of the document to reflect technical changes and improve the presentation. o Added the Issues section. Rosenberg, et al. Expires December 26, 2008 [Page 45] Internet-Draft TURN June 2008 19.4. Changes from -04 to -05 o Removed the ability to allocate addresses for TCP relaying. This is now covered in a separate document. However, communication between the client and the server can still run over TCP or TLS/ TCP. This resulted in the removal of the Connect method and the TIMER-VAL and CONNECT-STAT attributes. o Added the concept of channels. All communication between the client and the server flows on a channel. Channels are numbered 0..65535. Channel 0 is used for TURN messages, while the remaining channels are used for sending unencapsulated data to/ from a remote peer. This concept adds a new Channel Confirmation method and a new CHANNEL-NUMBER attribute. The new attribute is also used in the Send and Data methods. o The framing mechanism formally used just for stream-oriented transports is now also used for UDP, and the former Type and Reserved fields in the header have been replaced by a Channel Number field. The length field is zero when running over UDP. o TURN now runs on its own port, rather than using the STUN port. The use of channels requires this. o Removed the SetActiveDestination concept. This has been replaced by the concept of channels. o Changed the allocation refresh mechanism. The new mechanism uses a new Refresh method, rather than repeating the Allocation transaction. o Changed the syntax of SRV requests for secure transport. The new syntax is "_turns._tcp" rather than the old "_turn._tls". This change mirrors the corresponding change in STUN SRV syntax. o Renamed the old REMOTE-ADDRESS attribute to PEER-ADDRESS, and changed it to use the XOR-MAPPED-ADDRESS format. o Changed the RELAY-ADDRESS attribute to use the XOR-MAPPED-ADDRESS format (instead of the MAPPED-ADDRESS format)). o Renamed the 437 error code from "No Binding" to "Allocation Mismatch". o Added a discussion of what happens if a client's public binding on its outermost NAT changes. Rosenberg, et al. Expires December 26, 2008 [Page 46] Internet-Draft TURN June 2008 o The document now consistently uses the term "peer" as the name of a remote endpoint with which the client wishes to communicate. o Rewrote much of the document to describe the new concepts. At the same time, tried to make the presentation clearer and less repetitive. 20. Open Issues NOTE to RFC Editor: Please remove this section prior to publication of this document as an RFC. Bandwidth: How should bandwidth be specified? What are the right rules around bandwidth? Alternate Server: Do we still want this mechanism? Is the current proposal acceptable? Note that the usage of the ALTERNATE-SERVER attribute in this document is inconsistent with its usage in STUN. In STUN, if the ALTERNATE-SERVER attribute is used, then the error that the server would otherwise generate is replaced by a 300 (Try Alternate) code. In this document, the 300 error code is not used, and the server returns an appropriate error code and then includes the ALTERNATE-SERVER attribute in the response. In this way, the client can see the actual error code, rather than always seeing error code 300, and can thus make a more intelligent decision on whether it wishes to try the alternate server. Public TURN servers: The text currently says that a server "SHOULD" use the Long-Term Credential mechanism, with the unstated idea that a public TURN server would not use it. But this really weakens the security of TURN. Is there a better way to allow public servers? Or should we just drop the notion of a public server entirely? 21. Acknowledgements The authors would like to thank the various participants in the BEHAVE working group for their many comments on this draft. Marc Petit-Huguenin, Remi Denis-Courmont, Derek MacDonald, Cullen Jennings, Lars Eggert, Magnus Westerlund, and Eric Rescorla have been particularly helpful, with Eric also suggesting the channel allocation mechanism, and Cullen suggesting the REQUESTED-PROPS mechanism. Christian Huitema was an early contributor to this document and was a co-author on the first few drafts. Finally, the authors would like to thank Dan Wing for both his contributions to the text and his huge help in restarting progress on this draft after work had stalled. Rosenberg, et al. Expires December 26, 2008 [Page 47] Internet-Draft TURN June 2008 22. References 22.1. Normative References [I-D.ietf-behave-rfc3489bis] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing, "Session Traversal Utilities for (NAT) (STUN)", draft-ietf-behave-rfc3489bis-15 (work in progress), February 2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3697] Rajahalme, J., Conta, A., Carpenter, B., and S. Deering, "IPv6 Flow Label Specification", RFC 3697, March 2004. 22.2. Informative References [RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, February 1996. [RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery for IP version 6", RFC 1981, August 1996. [RFC3264] Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model with Session Description Protocol (SDP)", RFC 3264, June 2002. [RFC4302] Kent, S., "IP Authentication Header", RFC 4302, December 2005. [RFC4303] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC 4303, December 2005. [RFC3424] Daigle, L. and IAB, "IAB Considerations for UNilateral Self-Address Fixing (UNSAF) Across Network Address Translation", RFC 3424, November 2002. [I-D.ietf-mmusic-ice] Rosenberg, J., "Interactive Connectivity Establishment (ICE): A Protocol for Network Address Translator (NAT) Traversal for Offer/Answer Protocols", draft-ietf-mmusic-ice-19 (work in progress), October 2007. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. Rosenberg, et al. Expires December 26, 2008 [Page 48] Internet-Draft TURN June 2008 [I-D.ietf-behave-turn-tcp] Rosenberg, J. and R. Mahy, "Traversal Using Relays around NAT (TURN) Extensions for TCP Allocations", draft-ietf-behave-turn-tcp-00 (work in progress), November 2007. [I-D.ietf-behave-turn-ipv6] Camarillo, G. and O. Novo, "Traversal Using Relays around NAT (TURN) Extension for IPv4/IPv6 Transition", draft-ietf-behave-turn-ipv6-04 (work in progress), January 2008. [I-D.ietf-tsvwg-udp-guidelines] Eggert, L. and G. Fairhurst, "Guidelines for Application Designers on Using Unicast UDP", draft-ietf-tsvwg-udp-guidelines-08 (work in progress), June 2008. [RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191, November 1990. [RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU Discovery", RFC 4821, March 2007. [RFC1928] Leech, M., Ganis, M., Lee, Y., Kuris, R., Koblas, D., and L. Jones, "SOCKS Protocol Version 5", RFC 1928, March 1996. [Port-Numbers] "IANA Port Numbers Registry", . [Protocol-Numbers] "IANA Protocol Numbers Registry", 2005, . Authors' Addresses Jonathan Rosenberg Cisco Systems, Inc. Edison, NJ USA Email: jdrosen@cisco.com URI: http://www.jdrosen.net Rosenberg, et al. Expires December 26, 2008 [Page 49] Internet-Draft TURN June 2008 Rohan Mahy Plantronics, Inc. Email: rohan@ekabal.com Philip Matthews (Unaffiliated) Fax: Email: philip_matthews@magma.ca URI: Rosenberg, et al. Expires December 26, 2008 [Page 50] Internet-Draft TURN June 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Rosenberg, et al. Expires December 26, 2008 [Page 51]