DCCP Working Group G. Fairhurst Internet-Draft University of Aberdeen Updates: 4340 (if approved) May 02, 2009 Intended status: Standards Track Expires: November 3, 2009 DCCP Simultaneous-Open Technique to Facilitate NAT/Middlebox Traversal draft-ietf-dccp-simul-open-08 Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on November 3, 2009. Copyright Notice Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Fairhurst Expires November 3, 2009 [Page 1] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Abstract This document specifies an update to the Datagram Congestion Control Protocol (DCCP), a connection-oriented and datagram-based transport protocol. The update adds support for the DCCP-Listen packet. This assists DCCP applications to communicate through middleboxes (e.g. a DCCP server behind a firewall, or a Network Address Port Translator), where peering endpoints need to initiate communication in a near- simultaneous manner to establish necessary middlebox state. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Scope of this Document . . . . . . . . . . . . . . . . . . 3 1.2. DCCP NAT Traversal . . . . . . . . . . . . . . . . . . . . 3 1.3. Structure of this Document . . . . . . . . . . . . . . . . 4 2. Procedure for Near-Simultaneous Open . . . . . . . . . . . . . 5 2.1. Conventions and Terminology . . . . . . . . . . . . . . . 5 2.2. Protocol Method . . . . . . . . . . . . . . . . . . . . . 5 2.2.1. DCCP-Listen Packet Format . . . . . . . . . . . . . . 5 2.2.2. Protocol Method for DCCP Server Endpoints . . . . . . 8 2.2.3. Protocol Method for DCCP Client Endpoints . . . . . . 11 2.2.4. Processing by Routers and Middleboxes . . . . . . . . 12 2.3. Examples of Use . . . . . . . . . . . . . . . . . . . . . 13 2.3.1. Repetition of DCCP-Listen . . . . . . . . . . . . . . 13 2.3.2. Optional Triggered Retransmission of DCCP-Request . . 15 2.4. Backwards Compatibility with RFC 4340 . . . . . . . . . . 16 3. Discussion of Design Decisions . . . . . . . . . . . . . . . . 17 3.1. Rationale for a New Packet Type . . . . . . . . . . . . . 17 3.1.1. Use of sequence numbers . . . . . . . . . . . . . . . 18 3.2. Generation of Listen Packets . . . . . . . . . . . . . . . 18 3.3. Repetition of DCCP-Listen Packets . . . . . . . . . . . . 18 4. Security Considerations . . . . . . . . . . . . . . . . . . . 20 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22 6. Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7. References . . . . . . . . . . . . . . . . . . . . . . . . . . 26 7.1. Normative References . . . . . . . . . . . . . . . . . . . 26 7.2. Informative References . . . . . . . . . . . . . . . . . . 26 Appendix A. Discussion of Existing NAT Traversal Techniques . . . 28 A.1. NAT traversal Based on a Simultaneous-Request . . . . . . 29 A.2. Role Reversal . . . . . . . . . . . . . . . . . . . . . . 30 Appendix B. Change Log - to be removed by RFC-Ed . . . . . . . . 31 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 34 Fairhurst Expires November 3, 2009 [Page 2] Internet-Draft DCCP Simultaneous-Open Technique May 2009 1. Introduction The Datagram Congestion Control Protocol (DCCP) [RFC4340] is both datagram-based and connection-oriented. According to RFC 4340, DCCP servers establish connections by passively listening for incoming connection requests that are actively transmitted by DCCP clients. These asymmetric roles can cause problems when the server is 'inside' a middlebox, such as a Network Address and Port Translator (NAPT) that only allows connection requests to be initiated from inside (e.g. due to port overloading) [ID-BEHAVE-DCCP]. Host-based and network firewalls can also implement policies that lead to similar problems. This behaviour is currently the default for many firewalls. UDP can support middlebox traversal using various techniques [RFC4787] that leverage the connectionless nature of UDP and are therefore not suitable for DCCP. TCP supports middlebox traversal through the use of its simultaneous open procedure [RFC5382]. The concepts of the TCP solution are applicable to DCCP, but DCCP can not simply reuse the same methods (see Appendix A). After discussing the problem space for DCCP, this document specifies an update to the DCCP state machine to offer native support to allow a DCCP client to establish a connection to a DCCP server that is inside one or more middleboxes. This reduces dependence on external aids such as data relay servers [ID-BEHAVE-TURN] by explicitly supporting a widely used principle known as 'hole punching'. The method requires only a minor change to the standard DCCP operational procedure. The use of a dedicated DCCP packet type ties usage to a specific condition, ensuring the method is inter-operable with hosts that do not implement this update, or choose to disable it (see Section 4). 1.1. Scope of this Document This method is useful in scenarios when a DCCP server is located inside the perimeter controlled by a middlebox. It is relevant to both client/server and peer-to-peer applications, such as VoIP, file sharing, or online gaming and assists connections that utilise prior out-of-band signaling (e.g. via a well-known rendezvous server ([RFC3261], [H.323])) to notify both endpoints of the connection parameters ([RFC3235], [NAT-APP]). 1.2. DCCP NAT Traversal The behavioural requirements for NAT devices supporting DCCP are described in [ID-BEHAVE-DCCP]. A "traditional NAT" [RFC3022], that Fairhurst Expires November 3, 2009 [Page 3] Internet-Draft DCCP Simultaneous-Open Technique May 2009 directly maps an IP address to a different IP address does not require the simultaneous open method described in this document. The method is required when the DCCP server is positioned behind one or more NAPT devices in the path (hierarchies of nested NAPT devices are possible). This document refers to DCCP hosts located inside the perimeter controlled by one or more NAPT devices as having "private" addresses, and to DCCP hosts located in the global address realm as having "public" addresses. DCCP NAT traversal is considered for the following scenarios: 1. Private client connects to public server. 2. Public client connects to private server. 3. Private client connects to private server. A defining characteristic of traditional NAT devices [RFC3022] is that private hosts can connect to external hosts, but not vice versa. Hence the case (1) is possible using the protocol defined in [RFC4340]. A pre-configured, static NAT address map would allow outside hosts to connections in cases (2) and (3). A DCCP implementation conforming to [RFC4340] and a NAT device conforming to [ID-BEHAVE-DCCP] would require a DCCP relay server to perform NAT traversal for cases (2) and (3). This document describes a method to support cases (2) and (3) without the aid of a DCCP relay server. This method updates RFC 4340 and requires the DCCP server to discover the IP address and the DCCP port that correspond to the DCCP client. Such signalling may be performed out-of-band (e.g. using SDP [RFC4566]). 1.3. Structure of this Document For background information on existing NAT traversal techniques, please consult Appendix A. The normative specification of the update is presented in Section 2. An informative discussion of underlying design decisions then follows, in Section 3. Security considerations are provided in Section 4 and IANA considerations in the concluding Section 5. Fairhurst Expires November 3, 2009 [Page 4] Internet-Draft DCCP Simultaneous-Open Technique May 2009 2. Procedure for Near-Simultaneous Open This section is normative and specifies the simultaneous-open technique for DCCP. It updates the connection-establishment procedures of [RFC4340]. 2.1. Conventions and Terminology The document uses the terms and definitions provided in [RFC4340]. Familiarity with this specification is assumed. In particular, the following convention from ([RFC4340], 3.2) is used: "Each DCCP connection runs between two hosts, which we often name DCCP A and DCCP B. Each connection is actively initiated by one of the hosts, which we call the client; the other, initially passive host is called the server." The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2.2. Protocol Method The term "session" is used as defined in ([RFC2663], 2.3): DCCP sessions are uniquely identified by the tuple of . DCCP, in addition, introduces Service Codes, which can be used to identify different services available via the same port [ID-DCCP-SC]. 2.2.1. DCCP-Listen Packet Format This document adds a new DCCP packet type, DCCP-Listen, whose format is shown below. Fairhurst Expires November 3, 2009 [Page 5] Internet-Draft DCCP Simultaneous-Open Technique May 2009 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Port | Dest Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Data Offset | CCVal | CsCov | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Res | Type |X| Reserved | Sequence Number High Bits | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number Low Bits | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Service Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1: Format of a DCCP-Listen Packet o The Source Port is the port on which the DCCP server is listening for a connection from the IP address that appears as the destination IP address in the packet. o The Destination Port is the port selected by a DCCP client to identify a connection by the DCCP client. In this technique, this value must be communicated out-of-band to the server. o The value of X MUST be set to 1. A DCCP-Listen packet is sent before a connection is established, therefore there is no way to negotiate use of short sequence numbers ([RFC4340], 5.1). o The value of the sequence number field in a DCCP-Listen packet is not related to the DCCP sequence number used in normal DCCP messages (see Section 3 for a description of the use of the DCCP sequence number). Thus, for DCCP-Listen packets: * A DCCP server SHOULD set the high and low bits of the Sequence Number field to 0. * A DCCP client MUST ignore the value of the Sequence Number field. * Middleboxes MUST NOT interpret sequence numbers on DCCP-Listen packets. o The Service Code field contains the Service Code value for which the server is listening for a connection ([RFC4340], 8.1.2, [ID-DCCP-SC]). This value MUST correspond to a Service Code that the server is actually offering for a connection identified by the same source IP address and the same Source Port as that of the DCCP-Listen packet. Since the server may use multiple Service Fairhurst Expires November 3, 2009 [Page 6] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Codes, the specific value of the Service Code field needs to be communicated out-of-band, from client to server, prior to sending the DCCP-Listen packet, e.g. described using the Session Description Protocol, SDP [RFC4566]. o At the time of writing, there are no known uses of header options ([RFC4340] , sec. 5.8) with a DCCP-Listen packet. Clients MUST ignore all options in received DCCP-Listen packets. Therefore, feature values can not be negotiated using a DCCP-Listen packet. o At the time of writing, there are no known uses of payload data with a DCCP-Listen packet. Since DCCP-Listen packets are issued before an actual connection is established, endpoints MUST ignore any payload data encountered in DCCP-Listen packets. o The following protocol fields are required to have specific values: * Data Offset MUST have a value of five or more (i.e. at least 20 bytes). * CCVal MUST be zero (a connection has not been established). * CsCov MUST be zero (use of the CsCov feature can not be negotiated). * Type has the value 10, assigned by IANA to denote a DCCP-Listen packet. * X MUST be 1 (the Generic header must be used). The remaining fields, including the "Res" and "Reserved" fields are specified by [RFC4340] and its successors. The interpretation of these fields is not modified by this document. Fairhurst Expires November 3, 2009 [Page 7] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Note to the RFC Editor: This value assigned to the DCCP-Listen packet needs to be confirmed by IANA when this document is published. Please then remove this note. ==> End of note to the RFC Editor. <== 2.2.2. Protocol Method for DCCP Server Endpoints This document updates section 8.1 of [RFC4340] for the case of a fully specified DCCP server endpoint. The update modifies the way the server performs a passive-open. Prior to connection setup, it is common for a DCCP server endpoint to not be fully specified: before the connection is established, a server usually specifies only the destination port, and Service Code. (Sometimes the destination address is also specified.) This leaves the source address and source port unspecified. The endpoint only becomes fully specified after performing the handshake for an incoming connection. For such cases, this document does not update [RFC4340], i.e. the server adheres to the existing state transitions in the left half of Figure 2 (CLOSED => LISTEN => RESPOND). A fully specified DCCP server endpoint permits exactly one client, identified by source IP-address:port, destination IP-address:port, plus a single Service Code, to set up the connection. Such a server SHOULD perform the actions and state transitions shown in the right half of Figure 2 in section 8.4, and specified below. Fairhurst Expires November 3, 2009 [Page 8] Internet-Draft DCCP Simultaneous-Open Technique May 2009 unspecified remote +--------+ fully specified remote +---------------------| CLOSED |---------------------+ | +--------+ send DCCP-Listen | | | v v +--------+ timeout +---------+ | LISTEN | +---+-----------| INVITED | +--------+ | | +---------+ | | | 1st / 2nd ^ | | more than 2 | | retransm. | | receive | retransmissions | +-------------+ | Request | | resend Listen v | | +---------+ | +-------------->| LISTEN1 | | +---------+ | | | receive Request +---------+ receive Request* | +------------------->| RESPOND |<--------------------+ send Response +---------+ send Response * Note: A server that responds a DCCP-Request in the INVITED state, transitions to the LISTEN1 state and then immediately transitions to the RESPOND state. This does not require reception of an additional DCCP-Request packet. Figure 2: Updated state transition diagram for DCCP-Listen This diagram introduces two additional DCCP server states in addition to those listed in section 4.3 of [RFC4340]: o INVITED The INVITED state is associated with a specific DCCP connection and represents a fully-specified server socket in the listening state that is generating DCCP-Listen packets towards the client. o LISTEN1 The LISTEN1 state is associated with a specific DCCP connection and represents a fully-specified server socket in the passive listening state that will not generate further DCCP-Listen packets towards the client. A fully specified server endpoint performs a passive-open from the CLOSED state by inviting the remote client to connect. This is performed by sending a single DCCP-Listen packet to the specified remote IP-address:port, using the format specified in Section 2.2.1. The figure below provides pseudocode describing the packet processing in the INVITED state. This processing step follows Step 2 in section 8,5 of [RFC4340]). Fairhurst Expires November 3, 2009 [Page 9] Internet-Draft DCCP Simultaneous-Open Technique May 2009 The INVITED state is, like LISTEN, a passive state, characterised by waiting in the absence of an established connection. If the server endpoint in the INVITED state receives a DCCP-Request that matches the set of bound ports and addresses, it transitions to the LISTEN' state and then immediately transitions to the RESPOND state, where further processing resumes as specified in [RFC4340]. The server SHOULD repeat sending a DCCP-Listen packet while in the INVITED state, at a 200 millisecond interval with up to at most 2 repetitions (Section 3 discusses this choice of time interval). If the server is still in the INVITED state after a further period of 200ms following transmission of the third DCCP-Listen packet, it SHOULD progress to the LISTEN1state. Fully specified server endpoints SHOULD treat ICMP error messages received in response to a DCCP-Listen packet as "soft errors" that do not cause a state transition. Reception of an ICMP error message as a result of sending a DCCP-Listen packet does not necessarily indicate a failure of the following connection request, and therefore should not result in a server state change. This reaction to soft errors exploits the valuable feature of the Internet that for many network failures, the network can be dynamically reconstructed without any disruption of the endpoints. Server endpoints SHOULD ignore any incoming DCCP-Listen packets. A DCCP server in the LISTEN, INVITED, or LISTEN1states MAY generate a DCCP-Reset packet (Code 7, "Connection Refused") in response to a received DCCP-Listen packet. This DCCP-Reset packet is an indication that two servers are simultaneously awaiting connections on the same port. Further details on the design rationale are discussed in Section 3. The figure below provides pseudocode describing the packet processing in the INVITED state. This processing step follows Step 2 in section 8.5 of RFC 4340 [RFC4340] Fairhurst Expires November 3, 2009 [Page 10] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Step 2a: Process INVITED state If S.state == INVITED, /* State only entered for fully-specified server endpoints */ /* on entry S will have been set to a socket */ If P.type == Request /* Exit INVITED state and continue to process the packet */ S.state = LISTEN1 Continue with S.state := LISTEN1 Otherwise, If P.type == Listen /* The following line is optional */ Generate Reset(Connection Refused) /* otherwise Drop packet and return */ Otherwise, Generate Reset(No Connection) unless P.type == Reset Step 2b: Process LISTEN1 state If S.state == LISTEN1, /* State only entered for fully-specified server endpoints */ /* Follows receipt of a Response packet */ /* or sending third Listen packet (after timer expiry) */ If P.type == Request, S.state = RESPOND Choose S.ISS (initial seqno) or set from Init Cookies Initialize S.GAR := S.ISS Set S.ISR, S.GSR, S.SWL, S.SWH from packet or Init Cookies Continue with S.state == RESPOND /* A Response packet will be generated in Step 11 */ Otherwise, If P.type == Listen /* The following line is optional */ Generate Reset(Connection Refused) /* otherwise Drop packet and return */ Otherwise, Generate Reset(No Connection) unless P.type == Reset Figure 3: Updated DCCP pseudocode for INVITED and LISTEN' states 2.2.3. Protocol Method for DCCP Client Endpoints This document updates section 8.1.1 of [RFC4340], by adding the following rule for the reception of DCCP-Listen packets by clients: A client in any state MUST silently discard any received DCCP-Listen packet, unless it implements the optional procedure defined in the following section. Fairhurst Expires November 3, 2009 [Page 11] Internet-Draft DCCP Simultaneous-Open Technique May 2009 2.2.3.1. Optional generation of Triggered Requests This section describes an optional optimisation at the client that can avoid clients having to wait for a timeout following a dropped DCCP-Request. The operation requires clients to respond to reception of DCCP-Listen packets when received in the REQUEST state. DCCP- Listen packets MUST be silently discarded in all other states. A client implementing this optmisation MAY immediately perform a retransmission of a DCCP-Request following the reception of the first DCCP-Listen packet. The retransmission is performed in the same manner as a timeout in the REQUEST state [RFC4340]. A triggered retransmission SHOULD result in the client increasing the exponential-backoff timer interval. Note that a path delay greater than 200ms will result in multiple DCCP-Listen packets arriving at the client before a DCCP-Response is received. Clients MUST therefore perform only one such retransmission for each DCCP connection. This requires maintaining local state (e.g. one flag per connection) Implementors and users of this optional method need to be aware that host timing or path reordering can result in a server receiving two DCCP-Requests (i.e., the server sending one unnecessary packet). This would, in turn, trigger a client to send a second corresponding DCCP-Response (also unnecessary). These additional packets are not expected to modify or delay the DCCP open procedure [RFC4340]. Section 2.3.2 provides examples of the use of triggered retransmission. 2.2.4. Processing by Routers and Middleboxes DCCP-Listen packets do not require special treatment and should thus be forwarded end-to-end across Internet paths, by routers and middleboxes alike. Middleboxes may utilise the connection information (address, port, Service Code) to establish local forwarding state. The DCCP-Listen packet carries the necessary information to uniquely identify a DCCP session in combination with the source and destination addresses (found in the enclosing IP-header), including the DCCP Service Code value [ID-DCCP-SC]. The processing of the DCCP-Listen packet by NAT devices is specified in [ID-BEHAVE-DCCP]. Fairhurst Expires November 3, 2009 [Page 12] Internet-Draft DCCP Simultaneous-Open Technique May 2009 2.3. Examples of Use In the examples below, DCCP A is the client and DCCP B is the server. A middlebox device (NAT/Firewall), NA is placed before DCCP A, and another middlebox, NB, is placed before DCCP B. Both NA and NB use a policy that permits DCCP packets to traverse the device for outgoing links, but only permit incoming DCCP packets when a previous packet has been sent out for the same connection. In the figure below, DCCP A and DCCP B decide to communicate using an out-of-band mechanism (in this case labelled SDP), whereupon the client and server are started. DCCP B actively indicates its listening state by sending a DCCP-Listen message. This fulfils the requirement of punching a hole in NB (also creating the binding to the external address and port). This message is dropped by NA since no hole exists there yet. DCCP A initiates a connection by entering the REQUEST state and sending a DCCP-Request. (It is assumed that if NA were a NAT device, then this would also result in a binding that maps the pinhole to the external address and port.) The DCCP-Request is received by DCCP B, via the binding at NB. DCCP B transmits the DCCP-Response and connects through the bindings now in place at NA and NB. DCCP A DCCP B ------ NA NB ------ +-----------------+ +-+ +-+ +-----------------+ | | | | | | | | State = CLOSED | SDP --> |--+-+----+-+->| | State = INVITED | | | |X---+-+--|<-- DCCP-Listen | |(State=REQUEST) | | | | | | | |DCCP-Request --> |--+-+----+-+->| | |(State=PARTOPEN) | <+-+----+-+--|<-- DCCP-Response| State = RESPOND |DCCP-Ack --> |--+-+----+-+> | | | | | | | | | | | | | | | | | | |DCCP-Data --> |--+-+----+-+->| | State = OPEN +-----------------+ +-+ +-+ +-----------------+ Figure 4: Event sequence when the server is started before the client 2.3.1. Repetition of DCCP-Listen This section examines the effect of not receiving the DCCP-Request. The figure below shows the sequence of packets where the DCCP server enters the INVITED state after reception of out-of-band signaling (e.g. SDP). The key timer operations at the client and server are respectively shown on the left and right of the diagram. It Fairhurst Expires November 3, 2009 [Page 13] Internet-Draft DCCP Simultaneous-Open Technique May 2009 considers the case when the server does not receive a DCCP-Request within the first 600 ms (often the request would be received within this interval). The repetition of DCCP-Listen packets may be implemented using a timer. The timer is restarted with an interval of 200ms when sending each DCCP-Listen packet. It is cancelled when the server leaves the INVITED state. If the timer expires after the first and second transmission, it triggers a transmission of another DCCP-Listen Packet. If it expires after sending the third DCCP-Listen packet, the server leaves the INVITED state, to enter the LISTEN1state (where it passively waits for a DCCP-Request). DCCP A DCCP B ------ NA NB ------ +----+ +-+ +-+ +-----------------+ | | | | | | | | State = CLOSED | -->|--+-+----+-+--|--> SDP | | | | | | | | | State = INVITED | | | | | | | | | | | |X---+-+--|<-- DCCP-Listen | Timer Starts | | | | | | | | | DCCP-Request | -->|--->+--X | | | (dropped) | | Timer Starts | | | | | | | | | | | | | | | | | | 1st Timer Expiry | | |<-+-+----+++--|<-- DCCP-Listen | | | | | | | | | | Timer Starts | | | | | | | | | | | | | | | | | | | 2nd Timer Expiry | | | | | | | | | | | |<-+-+----+-+--|<-- DCCP-Listen | Timer Starts | | | | | | | | | | | | | | | | | | | 3rd Timer Expiry | | | | | | | | | | | | | | | | | | State = LISTEN1 | ~ ~ ~ ~ ~ ~ ~ ~ | | | | | | | | | Timer Expiry | -->|--+-+----+-+--|--> DCCP-Request | | | | | | | | | State = RESPOND | <--|--+-+----+-+--|<-- DCCP-Response| +----+ +-+ +-+ +-----------------+ Figure 5: Repetition of the DCCP-Listen Packet Fairhurst Expires November 3, 2009 [Page 14] Internet-Draft DCCP Simultaneous-Open Technique May 2009 2.3.2. Optional Triggered Retransmission of DCCP-Request The following figure illustrates a triggered retransmission. In this figure, the first DCCP-Listen is assumed to be lost in the network (e.g. does not open a pin-hole at NB). A later DCCP-Request is also not received (perhaps as a side-effect of the first loss). After 200ms, the DCCP-Listen packet is retransmitted and correctly received. This triggers the retransmission of the DCCP-Request, which, when received, results in a corresponding DCCP-Response. DCCP A DCCP B ------ NA NB ------ +-----------------+ +-+ +-+ +-----------------+ | | | | | | | | State = CLOSED |SDP |--+-+----+-+->| | State = INVITED |(State= REQUEST) | | | | | | | | | | | | |X-|<-- DCCP-Listen | |DCCP-Request --> |--+-+---X| | | | | | <+-+----+-+--|<-- DCCP-Listen |(retransmit) | | | | | | | | |DCCP-Request --> |--+-+----+-+->| | State = RESPOND | (Triggered) | | | | | | | | |<-+-+----+-+--|<-- DCCP-Response| |(State= PARTOPEN)| | | | | | | |DCCP-Ack --> |--+-+----+-+->| | State = OPEN +-----------------+ +-+ +-+ +-----------------+ Figure 6: Example showing a triggered DCCP-Request The figure below illustrates the sequence of packets exchanged when a DCCP-Listen and DCCP-Request are processed out of order. Reception of the DCCP-Listen packet by the client triggers retransmission of the DCCP-Request. The server responds to the first DCCP-Request, and enters the RESPOND state. The server subsequently responds to the second DCCP-Request with another DCCP-Response, which is ignored by the client (already in the PARTOPEN state). Fairhurst Expires November 3, 2009 [Page 15] Internet-Draft DCCP Simultaneous-Open Technique May 2009 DCCP A DCCP B ------ NA NB ------ +-----------------+ +-+ +-+ +-----------------+ | | | | | | | | State = CLOSED |SDP |--+-+----+-+->| | State = INVITED |(State = REQUEST)| | | | | | | |DCCP-Request --> |--+-+- -+-+--|<-- DCCP-Listen | | | | | \/ | | | | | | | | /\ | | | | | |<-+-+- -+-+->| | |DCCP-Request --> |--+-+- -+-+--|<-- DCCP-Response| State = RESPOND | (Triggered) | | | \/ | | | | | | | | /\ | | | | | |<-+-+- -+-+->| | |(State= PARTOPEN)| | | | | | | |DCCP-Ack --> |--+-+- -+-+--|<-- DCCP-Response| | (Triggered) | | | \/ | | | | | | | | /\ | | | | | (Ignored) |<-+-+- -+-+->| | State = OPEN | | | | | | | | +-----------------+ +-+ +-+ +-----------------+ Figure 7: Example showing an unnecessary triggered DCCP-Request 2.4. Backwards Compatibility with RFC 4340 No changes are required if a DCCP client conforming to this document communicates with a DCCP server conforming to [RFC4340]. If a client implements only [RFC4340], an incoming DCCP-Listen packet would be ignored due to step 1 in [RFC4340], 8.1, which at the same time also conforms to the behaviour specified by this document. This document further does not modify communication for any DCCP server that implements a passive-open without fully binding the addresses, ports and Service Codes to be used. The authors therefore do not expect practical deployment problems with existing conformant DCCP implementations. Fairhurst Expires November 3, 2009 [Page 16] Internet-Draft DCCP Simultaneous-Open Technique May 2009 3. Discussion of Design Decisions This is an informative section that reviews the rationale for the design of this method. 3.1. Rationale for a New Packet Type The DCCP-Listen packet specified in Section 2.2.1 has the same format as the DCCP-Request packet ([RFC4340], 5.1), the only difference is in the value of the Type field. The usage, however, differs. The DCCP-Listen packet serves as an advisory message, not as part of the actual connection setup: sequence numbers have no meaning, and no payload can be communicated. A DCCP-Request packet could in theory also have been used for the same purpose. The following arguments were against this: The first problem was that of semantic overloading: the DCCP-Request defined in [RFC4340] serves a well-defined purpose, being the initial packet of the 3-way handshake. Additional use in the manner of a DCCP-Listen packet would have required DCCP processors to have had two different processing paths: one where a DCCP-Request was interpreted as part of the initial handshake, and another where the same packet was interpreted as an indicator message. This would complicate packet processing in hosts and in particular stateful middleboxes (which may have restricted computational resources). The second problem is that a client receiving a DCCP-Request from a server could generate a DCCP-Reset packet if it had not yet entered the REQUEST state (step 7 in [RFC4340], 8.5). The method specified in this document lets client endpoints ignore DCCP-Listen packets. Adding a similar rule for the DCCP-Request packet would have been cumbersome: clients would not have been able to distinguish between a Request meant to be an indicator message and a genuinely erratic connection initiation. The third problem is similar, and refers to a client receiving the indication after having itself sent a (connection-initiation) DCCP- Request. Step 7 in section 8.5 of [RFC4340] requires the client to reply to an "indicator message" Request from the server with a DCCP- Sync. Since sequence numbers are ignored for this type of message, additional and complex processing would become necessary: either to ask the client not to respond to a DCCP-Request when the request is of type "indicator message"; or ask middleboxes and servers to ignore Sync packets generated in response to "indicator message" DCCP- Requests. Furthermore, since no initial sequence numbers have been negotiated at this stage, sending a DCCP-SyncAck would not be meaningful. Fairhurst Expires November 3, 2009 [Page 17] Internet-Draft DCCP Simultaneous-Open Technique May 2009 The use of a separate packet type therefore allows simpler and clearer processing. 3.1.1. Use of sequence numbers Although the DCCP-Listen sequence number fields are ignored, they have been retained in the DCCP-Listen packet header to reuse the generic header format from section 5.1 of [RFC4340]. DCCP assigns a random initial value to the sequence number when a DCCP connection is established [RFC4340]. However, a sender is required to set this value to zero for a DCCP-Listen packet. Both clients and middleboxes are also required to ignore this value. The rationale for ignoring the sequence number fields of DCCP-Listen packets is that at the time the DCCP-Listen is exchanged, the endpoints have not yet entered connection setup: the DCCP-Listen packet is sent while the server is still in the passive-open (INVITED) state, i.e. it has not yet allocated state, other than binding to the client's IP-address:port and Service Code. 3.2. Generation of Listen Packets A DCCP server SHOULD by default permit generation of DCCP-Listen packets. Since DCCP-Listen packets solve a particular problem with NAT and/or firewall traversal, the generation of DCCP-Listen packets on passive sockets is tied to a condition (binding to an a priori known remote address and Service Code) to ensure this does not interfere with the general case of "normal" DCCP connections (where client addresses are generally not known in advance). In the TCP world, the analogue is a transition from LISTEN to SYN_SENT by virtue of sending data: "A fully specified passive call can be made active by the subsequent execution of a SEND" ([RFC0793], 3.8). Unlike TCP, this update does not perform a role-change from passive to active. Like TCP, DCCP-Listen packets are only sent by a DCCP-server when the endpoint is fully specified (Section 2.2). 3.3. Repetition of DCCP-Listen Packets Repetition is a necessary requirement, to increase robustness and the chance of successful connection establishment when a DCCP-Listen packet is lost due to congestion, link loss, or some other reason. The decision to recommend a maximum number of 3 timeouts (2 repeated copies of the original DCCP-Listen packet) results from the following considerations: The repeated copies need to be spaced sufficiently far apart in time to avoid suffering from correlated loss. The Fairhurst Expires November 3, 2009 [Page 18] Internet-Draft DCCP Simultaneous-Open Technique May 2009 interval of 200 ms was chosen to accommodate a wide range of wireless and wired network paths. Another constraint is given by the retransmission interval for the DCCP-Request ([RFC4340], 8.1.1). To establish state, intermediate systems need to receive a (retransmitted) DCCP-Listen packet before the DCCP-Request times out (1 second). With three timeouts, each spaced 200 milliseconds apart, the overall time is still below one second. On the other hand, the sum of 600 milliseconds is sufficiently large to provide for longer one-way delays, such as e.g. found on some wireless links. The rationale behind transitioning to the LISTEN1 state after two repetitions is that other problems, independent of establishing middlebox state, may occur (such as delay or loss of the initial DCCP-Request). Any late or retransmitted DCCP-Request packets will then still reach the server allowing connection establishment to successfully complete. Fairhurst Expires November 3, 2009 [Page 19] Internet-Draft DCCP Simultaneous-Open Technique May 2009 4. Security Considerations General security considerations for DCCP are described in [RFC4340]. Security considerations for Service Codes are further described in [ID-DCCP-SC]. The method specified in this document generates a DCCP-Listen packet addressed to a specific DCCP client. This exposes the state of a DCCP server that is in a passive listening state (i.e. waiting to accept a connection from a known client). The exposed information is not encrypted and therefore could be seen on the network path to the DCCP client. An attacker on this return path could observe a DCCP-Listen packet and then exploit this by spoofing a packet (e.g. DCCP-Request, DCCP-Reset) with the IP addresses, DCCP ports, and Service Code that correspond to the values to be used for the connection. As in other on-path attacks, this could be used to inject data into a connection or to deny a connection request. A similar on-path attack is also possible for any DCCP connection, once the session is initiated by the client ([RFC4340], Section 18). The DCCP-Listen packet is only sent in response to explicit prior out-of-band signaling from a DCCP client to the DCCP server (e.g. SDP [RFC4566]) information communicated via the Session Initiation Protocol [RFC3261]), and will normally directly precede a DCCP- Request sent by the client (which carries the same information). This update does not significantly increase the complexity or vulnerability of a DCCP implementation that conforms to [RFC4340]. A DCCP server should therefore by default permit generation of DCCP- Listen packets. A server that wishes to prevent disclosing this information MAY refrain from generating DCCP-Listen packets, without impacting subsequent DCCP state transitions, but possibly inhibiting middlebox traversal. The DCCP base specification in RFC 4340 defines an Init Cookie option, which lets a DCCP server avoid having to hold any state until the three-way connection setup handshake has completed. This specification enables an out-of-band mechanism that forces the server to hold state for a connection that has not yet been established. This is a change in the security profile of DCCP, although the impact is expected to be minimal and depends on the security features of the out-of-band mechanism (SIP SDP is one such mechanism that provides sufficient security features). The method creates a new way for a client to set up a DCCP connection to a server using out-of-band data, transported over a signaling Fairhurst Expires November 3, 2009 [Page 20] Internet-Draft DCCP Simultaneous-Open Technique May 2009 connection. If the signaling connection is not encrypted, an eavesdropper could see the client IP address and the port for the to- be-established DCCP connection and generate a DCCP-Listen packet towards the client using its own server-IP address and port. However, a client will only respond to a received DCCP-Listen packet if the server-IP address and port match an existing DCCP connection that is in the REQUEST state (section 2.3.2). The method therefore cannot be used to redirect the connection to a different server IP address. Fairhurst Expires November 3, 2009 [Page 21] Internet-Draft DCCP Simultaneous-Open Technique May 2009 5. IANA Considerations The IANA should register a new Packet Type, "DCCP-Listen", in the IANA DCCP Packet Types Registry. The decimal value 10 has been assigned to this type. This registry entry must reference this document. Fairhurst Expires November 3, 2009 [Page 22] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Note to the RFC Editor: This value of 10 must be confirmed by IANA in the registry when this document is published, please then remove this note. Fairhurst Expires November 3, 2009 [Page 23] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Acknowledgement This update was originally co-authored by Dr Gerrit Renker, University of Aberdeen, and the present author acknowledges his insight in design of the protocol mechanism and in careful review of the early revisions of the document text. Dan Wing assisted on issues relating to the use of NAT and NAPT. Fairhurst Expires November 3, 2009 [Page 24] Internet-Draft DCCP Simultaneous-Open Technique May 2009 6. Disclaimer This document may contain material from IETF Documents or IETF Contributions published or made publicly available before November 10, 2008. The person(s) controlling the copyright in some of this material may not have granted the IETF Trust the right to allow modifications of such material outside the IETF Standards Process. Without obtaining an adequate license from the person(s) controlling the copyright in such materials, this document may not be modified outside the IETF Standards Process, and derivative works of it may not be created outside the IETF Standards Process, except to format it for publication as an RFC or to translate it into languages other than English. Fairhurst Expires November 3, 2009 [Page 25] Internet-Draft DCCP Simultaneous-Open Technique May 2009 7. References 7.1. Normative References [ID-DCCP-SC] Fairhurst, G., "The DCCP Service Code", Work In Progress, draft-ietf-dccp-serv-codes-09, June 2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", March 1997. [RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram Congestion Control Protocol (DCCP)", March 2006. 7.2. Informative References [Epp05] Eppinger, J-L., "TCP Connections for P2P Apps: A Software Approach to Solving the NAT Problem", Carnegie Mellon University/ISRI Technical Report CMU-ISRI-05-104, January 2005. [FSK05] Ford, B., Srisuresh, P., and D. Kegel, "Peer-to-Peer Communication Across Network Address Translators", Proceedings of USENIX-05, pages 179-192, 2005. [GF05] Guha, S. and P. Francis, "Characterization and Measurement of TCP Traversal through NATs and Firewalls", Proceedings of Internet Measurement Conference (IMC-05), pages 199- 211, 2005. [GTF04] Guha, S., Takeda, Y., and P. Francis, "NUTSS: A SIP based approach to UDP and TCP connectivity", Proceedings of SIGCOMM-04 Workshops, Portland, OR, pages 43-48, 2004. [H.323] ITU-T, "Packet-based Multimedia Communications Systems", Recommendation H.323, July 2003. [ID-BEHAVE-DCCP] "Network Address Translation (NAT) Behavioral Requirements for DCCP", Work in Progress draft-ietf-behave-dccp-05.txt, 2008. [ID-BEHAVE-TURN] Rosenberg, J., Mahy, R., and P. Matthews, "Traversal Using Relays around NAT (TURN): Relay Extensions to Session Traversal Utilities for NAT (STUN)", Work In Progress, draft-ietf-behave-turn-14, February 2008. Fairhurst Expires November 3, 2009 [Page 26] Internet-Draft DCCP Simultaneous-Open Technique May 2009 [ID-MMUSIC-ICE] Rosenberg, J., "TCP Candidates with Interactive Connectivity Establishment (ICE)", Work In Progress, draft-ietf-mmusic-ice-tcp-07, February 2008. [NAT-APP] Ford, B., Srisuresh, P., and D. Kegel, "Application Design Guidelines for Traversal through Network Address Translators", Work In Progress, draft-ford-behave-app-05, March 2007. [RFC0793] Postel, J., "Transmission Control Protocol", September 1981. [RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address Translator (NAT) Terminology and Considerations", August 1999. [RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network Address Translator (Traditional NAT)", January 2001. [RFC3235] Senie, D., "Network Address Translator (NAT)-Friendly Application Design Guidelines", January 2002. [RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", June 2002. [RFC4566] "SDP: Session Description Protocol", July 2006. [RFC4787] "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", January 2007. [RFC5382] Guha, S., Biswas, K., Ford, B., Sivakumar, S., and P. Srisuresh, "NAT Behavioral Requirements for TCP", RFC5382, April 2007. Fairhurst Expires November 3, 2009 [Page 27] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Appendix A. Discussion of Existing NAT Traversal Techniques This appendix provides a brief review of existing techniques to establish connectivity across NAT devices, with the aim of providing background information. This first considers TCP NAT traversal based on simultaneous-open, and then discuss a second technique based on role reversal. Further information can be found in [GTF04] and [GF05]. A central idea shared by these techniques is to make peer-to-peer sessions look like "outbound" sessions on each NAT device. Often a rendezvous server, located in the public address realm, is used to enable clients to discover their NAT topology and the addresses of peers. The term 'hole punching' was coined in [FSK05] and refers to creating soft state in a traditional NAT device, by initiating an outbound connection. A well-behaved NAT can subsequently exploit this to allow a reverse connection back to the host in the private address realm. UDP and TCP hole punching use nearly the same technique [RFC4787]. The adaptation of the basic UDP hole punching principle to TCP NAT traversal [RFC5382] was introduced in section 4 of [FSK05] and relies on the simultaneous-open feature of TCP [RFC0793]. A further difference between UDP and TCP lies in the way the clients perform connectivity checks, after obtaining suitable address pairs for connection establishment. Whereas in UDP a single socket is sufficient, TCP clients require several sockets for the same address and port tuple: o a passive socket to listen for connectivity tests from peers and o multiple active connections from the same address to test reachability of other peers. The SYN sent out by client A to its peer B creates soft state in A's NAT. At the same time, B tries to connect to A: o if the SYN from B has left B's NAT before the arrival of A's SYN, both endpoints perform simultaneous-open (4-way handshake of SYN/ SYNACK); o otherwise A's SYN may not enter B's NAT, which leads to B performing a normal open (SYN_SENT => ESTABLISHED) and A performing a simultaneous-open (SYN_SENT => SYN_RCVD => ESTABLISHED). Fairhurst Expires November 3, 2009 [Page 28] Internet-Draft DCCP Simultaneous-Open Technique May 2009 In the latter case, it is necessary that the NAT does not interfere with a RST segment (REQ-4 in [RFC5382]). The simultaneous-open solution is convenient due to its simplicity, and is thus a preferred mode of operation in the TCP extension for ICE ([ID-MMUSIC-ICE], sec. 2). A.1. NAT traversal Based on a Simultaneous-Request Among the various TCP NAT traversal approaches, the one using a TCP simultaneous-open suggests itself as a candidate for DCCP due to its simplicity [GF05], [NAT-APP]. A characteristic of TCP simultaneous-open is that this erases the clear distinction between client and server: both sides enter through active (SYN_SENT) as well as passive (SYN_RCVD) states. This characteristic conflicts with the DCCP design decision to provide a clear separation between client and server functions ([RFC4340], 4.6). In DCCP several mechanisms implicitly rely on clearly-defined client/ server roles: o Feature Negotiation: with few exceptions, almost all of DCCP's negotiable features use the "server-priority" reconciliation rule ([RFC4340], 6.3.1), whereby a peer exchanges its preference lists of feature values, and the server decides the outcome. o Closing States: only a server may generate DCCP-CloseReq packets (asking the peer to hold timewait state), while a client is only permitted to send DCCP-Close or DCCP-Reset packets to terminate a connection ([RFC4340], 8.3). o Service Codes [ID-DCCP-SC]: a server may be associated with multiple Service Codes, while a client must be associated with exactly one ([RFC4340], 8.1.2). o Init Cookies: may only be used by a server and on DCCP-Response packets ([RFC4340], 8.1.4). The latter two points are not obstacles per se, but would have hindered the transition from a passive to an active socket. In DCCP, a DCCP-Request is only generated by a client. The assumption that "all DCCP hosts may be clients", was dismissed, since it would require undersirable changes to the state machine and would limit application programming. As a consequence, the retro-fitting a TCP- style simultaneous-open into DCCP to allow simulatenous exchange of DCCP-Connect packets was not recommended. Fairhurst Expires November 3, 2009 [Page 29] Internet-Draft DCCP Simultaneous-Open Technique May 2009 A.2. Role Reversal Another simple TCP NAT traversal scheme uses role traversal ([Epp05] and [GTF04]), where a peer first opens an active connection for the single purpose of punching a hole in the firewall; and then reverts to a listening socket, accepting connections arriving via the new path. This solution would have had several disadvantages if used with DCCP. First, a DCCP server would be required to change its role to temporarily become a 'client'. This would have required modification to the state machine, in particular the treatment of Service Codes and perhaps Init Cookies. Further, the method must follow feature negotiation, since an endpoint's choice of initial options can rely on its role (i.e. if an endpoint knows it is the server, it can make a priori assumptions about the preference lists of features it is negotiating with the client, thereby enforcing a particular policy). Finally, the server would have needed additional processing to ensure that the connection arriving at the listening socket matches the previously opened active connection. This approach was therefore not recommend for DCCP. Fairhurst Expires November 3, 2009 [Page 30] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Appendix B. Change Log - to be removed by RFC-Ed Revision 00 was based on a previous individual submission draft-fairhurst-dccp-behave-update-01 by the same authors. Revision 01: o introduced many format changes to improve readability o migrated background information into the Appendix o added Section 1.3 to summarize the document structure o updated introductory paragraph of Section 2 to account for new structure o added captions to all figures o updated the specification in Section 2 to (i) permit on DCCP- Listen packets; (ii) explain why the presence of payload data is not useful; (iii) clarify that middleboxes must not interpret sequence numbers on DCCP-Listen packets o clarified that the default value of the Allow Short Seqno feature is to be used o added references to the Service Code draft [ID-DCCP-SC] o clarified the processing of DCCP-Listen packets by server endpoints o corrected the reaction of a client implementing [RFC4340] only - DCCP-Listen packets are treated as unknown and hence do not generate a DCCP-Reset o swapped order of IANA / Security-Considerations sections o added a note in the Security Considerations section that servers may refrain from generating DCCP-Listen packets Revision 02: o minor edits following WG feedback at IETF meeting o updated to reflect ID.Behave-DCCP o update to reflect comments from Colin Perkins Fairhurst Expires November 3, 2009 [Page 31] Internet-Draft DCCP Simultaneous-Open Technique May 2009 o added a tentative IANA code point (as suggested at IETF-73) o DRAFT -02 o Edits following editorial corrections and suggestions from Tom Phelan o Edits following comments from Dan Wing on role of NAT, retransmission, and other issues. o Revised authors list o Reworded abstract, reworded appendices to clarify what was not done o Checked spelling o Although this version includes significant changes to format and text it does not seek to modify the intended procedure for a server. o o DRAFT - 03 o Comments by Dan Wing o DRAFT -04 o Corrections by Dan Wing, and new diagram Figure 5 to and text to clarify the retransmission algorithm. o DRAFT -05 o Sections re-ordered to bring the packet type definition to the front, and to correct a section mis-order in draft-04. References linked to IETF WGs and updated to satisfy IDNiTs. o A number of Typos were fixed. o DRAFT -06 o This draft follows a completed WGLC. o It includes responses to comments from Eddie Kohler, during WGLC. o Magnus Westerlund requested two updates: Fairhurst Expires November 3, 2009 [Page 32] Internet-Draft DCCP Simultaneous-Open Technique May 2009 o A triggered join, based on reception of a DCCP-Listen causing a retransmission of a DCCP-Request. o Updated figure 5. o Updated language to differentiate the loss-prevention DCCP-Listen repetition being confused with the DCCP-Request retransmission. o Added pseudocode and redrew state diagram, to match the pseudocode, including a transitory state transition to the LISTEN1state to process the received DCCP-Request. This is intended to be the same processing as in draft -05, even though the diagram now looks less pretty, and another state was created. o This version circulated in draft form to WG on 29/11/08 - no additional comments received. o Updated references. o o DRAFT -07 o Fixed Section heading (missing in rev -06) o Updated figure with a note to clarify the Response (from Magnus Westerlund). o Editorial corrections proposed by T.Phelan. o o DRAFT -08 o Fixed text in response to Sec-Dir review (Chris Newman) and GEN- ART review (Miguel A. Garcia) o SC draft made normative (draft currently with IESG) o Listen' changed to LISTEN1 in all places - to make this label clearer in the text o Security considerations updated o Addressed editorial comments received during LC. Fairhurst Expires November 3, 2009 [Page 33] Internet-Draft DCCP Simultaneous-Open Technique May 2009 Author's Address Godred Fairhurst University of Aberdeen School of Engineering Fraser Noble Building Aberdeen AB24 3UE Scotland Email: gorry@erg.abdn.ac.uk URI: http://www.erg.abdn.ac.uk Fairhurst Expires November 3, 2009 [Page 34]