Network Working Group C. Jennings, Ed. Internet-Draft Cisco Systems Updates: 3261,3327 R. Mahy, Ed. (if approved) Plantronics Intended status: Standards Track February 24, 2008 Expires: August 27, 2008 Managing Client Initiated Connections in the Session Initiation Protocol (SIP) draft-ietf-sip-outbound-12 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 27, 2008. Copyright Notice Copyright (C) The IETF Trust (2008). Abstract The Session Initiation Protocol (SIP) allows proxy servers to initiate TCP connections and send asynchronous UDP datagrams to User Agents in order to deliver requests. However, many practical considerations, such as the existence of firewalls and Network Address Translators (NATs), prevent servers from connecting to User Jennings & Mahy Expires August 27, 2008 [Page 1] Internet-Draft Client Initiated Connections in SIP February 2008 Agents in this way. This specification defines behaviors for User Agents, registrars and proxy servers that allow requests to be delivered on existing connections established by the User Agent. It also defines keep alive behaviors needed to keep NAT bindings open and specifies the usage of multiple connections from the User Agent to its Registrar. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Conventions and Terminology . . . . . . . . . . . . . . . . . 4 2.1. Definitions . . . . . . . . . . . . . . . . . . . . . . . 5 3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. Summary of Mechanism . . . . . . . . . . . . . . . . . . 6 3.2. Single Registrar and UA . . . . . . . . . . . . . . . . . 6 3.3. Multiple Connections from a User Agent . . . . . . . . . 8 3.4. Edge Proxies . . . . . . . . . . . . . . . . . . . . . . 10 3.5. Keep alive Technique . . . . . . . . . . . . . . . . . . 11 3.5.1. CRLF Keep-alive Technique . . . . . . . . . . . . . . 12 3.5.2. STUN Keep alive Technique . . . . . . . . . . . . . . 12 4. User Agent Mechanisms . . . . . . . . . . . . . . . . . . . . 12 4.1. Instance ID Creation . . . . . . . . . . . . . . . . . . 12 4.2. Registrations . . . . . . . . . . . . . . . . . . . . . . 14 4.2.1. Initial Registrations . . . . . . . . . . . . . . . . 14 4.2.2. Subsequent REGISTER requests . . . . . . . . . . . . . 16 4.2.3. Non Outbound Registrations . . . . . . . . . . . . . . 16 4.3. Sending Non-REGISTER Requests . . . . . . . . . . . . . . 16 4.4. Keep-alives and Detecting Flow Failure . . . . . . . . . 17 4.4.1. Keep alive with CRLF . . . . . . . . . . . . . . . . . 18 4.4.2. Keep alive with STUN . . . . . . . . . . . . . . . . . 19 4.5. Flow Recovery . . . . . . . . . . . . . . . . . . . . . . 19 5. Edge Proxy Mechanisms . . . . . . . . . . . . . . . . . . . . 20 5.1. Processing Register Requests . . . . . . . . . . . . . . 20 5.2. Generating Flow Tokens . . . . . . . . . . . . . . . . . 20 5.3. Forwarding Non-REGISTER Requests . . . . . . . . . . . . 21 5.4. Edge Proxy Keep alive Handling . . . . . . . . . . . . . 22 6. Registrar Mechanisms: Processing REGISTER Requests . . . . . . 22 7. Authoritative Proxy Mechanisms: Forwarding Requests . . . . . 24 8. STUN Keep alive Processing . . . . . . . . . . . . . . . . . . 25 8.1. Use with Sigcomp . . . . . . . . . . . . . . . . . . . . 26 9. Example Message Flow . . . . . . . . . . . . . . . . . . . . . 27 10. Grammar . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 11. New Response Codes . . . . . . . . . . . . . . . . . . . . . . 36 11.1. Definition of 430 Flow Failed response code . . . . . . . 36 11.2. Definition of 439 First Hop Lacks Outbound Support response . . . . . . . . . . . . . . . . . . . . . . . . 36 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 37 Jennings & Mahy Expires August 27, 2008 [Page 2] Internet-Draft Client Initiated Connections in SIP February 2008 12.1. Flow-Timer Header Field . . . . . . . . . . . . . . . . . 37 12.2. 'reg-id' Contact Header Field Parameter . . . . . . . . . 37 12.3. SIP/SIPS URI Parameters . . . . . . . . . . . . . . . . . 37 12.4. SIP Option Tag . . . . . . . . . . . . . . . . . . . . . 38 12.5. Response Codes . . . . . . . . . . . . . . . . . . . . . 38 12.5.1. 430 Response Code . . . . . . . . . . . . . . . . . . 38 12.5.2. 439 Response Code . . . . . . . . . . . . . . . . . . 38 12.6. Media Feature Tag . . . . . . . . . . . . . . . . . . . . 38 13. Security Considerations . . . . . . . . . . . . . . . . . . . 39 14. Operational Notes on Transports . . . . . . . . . . . . . . . 40 15. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 41 16. Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 16.1. Changes from 11 Version . . . . . . . . . . . . . . . . . 41 16.2. Changes from 09 Version . . . . . . . . . . . . . . . . . 41 16.3. Changes from 08 Version . . . . . . . . . . . . . . . . . 41 16.4. Changes from 07 Version . . . . . . . . . . . . . . . . . 42 16.5. Changes from 06 Version . . . . . . . . . . . . . . . . . 42 16.6. Changes from 05 Version . . . . . . . . . . . . . . . . . 42 16.7. Changes from 04 Version . . . . . . . . . . . . . . . . . 43 16.8. Changes from 03 Version . . . . . . . . . . . . . . . . . 44 16.9. Changes from 02 Version . . . . . . . . . . . . . . . . . 45 16.10. Changes from 01 Version . . . . . . . . . . . . . . . . . 45 16.11. Changes from 00 Version . . . . . . . . . . . . . . . . . 45 17. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 45 18. References . . . . . . . . . . . . . . . . . . . . . . . . . . 46 18.1. Normative References . . . . . . . . . . . . . . . . . . 46 18.2. Informational References . . . . . . . . . . . . . . . . 47 Appendix A. Default Flow Registration Backoff Times . . . . . . . 48 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 48 Intellectual Property and Copyright Statements . . . . . . . . . . 50 Jennings & Mahy Expires August 27, 2008 [Page 3] Internet-Draft Client Initiated Connections in SIP February 2008 1. Introduction There are many environments for SIP [RFC3261] deployments in which the User Agent (UA) can form a connection to a Registrar or Proxy but in which connections in the reverse direction to the UA are not possible. This can happen for several reasons. Connections to the UA can be blocked by a firewall device between the UA and the proxy or registrar, which will only allow new connections in the direction of the UA to the Proxy. Similarly a NAT could be present, which is only capable of allowing new connections from the private address side to the public side. This specification allows a SIP User Agent behind such a firewall or NAT to receive inbound traffic associated with registrations or dialogs that it initiates. Most IP phones and personal computers get their network configurations dynamically via a protocol such as DHCP (Dynamic Host Configuration Protocol). These systems typically do not have a useful name in the Domain Name System (DNS), and they almost never have a long-term, stable DNS name that is appropriate for use in the subjectAltName of a certificate, as required by [RFC3261]. However, these systems can still act as a Transport Layer Security (TLS) [RFC4346] client and form connections to a proxy or registrar which authenticates with a server certificate. The server can authenticate the UA using a shared secret in a digest challenge (as defined in Section 22 of RFC 3261) over that TLS connection. The key idea of this specification is that when a UA sends a REGISTER or a dialog-forming request, the proxy can later use this same network "flow"--whether this is a bidirectional stream of UDP datagrams, a TCP connection, or an analogous concept of another transport protocol--to forward any incoming requests that need to go to this UA in the context of the registration or dialog. For a UA to receive incoming requests, the UA has to connect to a server. Since the server can't connect to the UA, the UA has to make sure that a flow is always active. This requires the UA to detect when a flow fails. Since such detection takes time and leaves a window of opportunity for missed incoming requests, this mechanism allows the UA to register over multiple flows at the same time. This specification also defines multiple keep alive schemes. The keep alive mechanism is used to keep NAT bindings fresh, and to allow the UA to detect when a flow has failed. 2. Conventions and Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this Jennings & Mahy Expires August 27, 2008 [Page 4] Internet-Draft Client Initiated Connections in SIP February 2008 document are to be interpreted as described in RFC 2119 [RFC2119]. 2.1. Definitions Authoritative Proxy: A proxy that handles non-REGISTER requests for a specific Address-of-Record (AOR), performs the logical Location Server lookup described in RFC 3261, and forwards those requests to specific Contact URIs. Edge Proxy: An Edge Proxy is any proxy that is located topologically between the registering User Agent and the Authoritative Proxy. Flow: A Flow is a network protocol layer (layer 4) association between two hosts that is represented by the network address and port number of both ends and by the protocol. For TCP, a flow is equivalent to a TCP connection. For UDP a flow is a bidirectional stream of datagrams between a single pair of IP addresses and ports of both peers. With TCP, a flow often has a one to one correspondence with a single file descriptor in the operating system. Flow Token: An identifier which uniquely identifies a flow which can be included in a SIP URI (Uniform Resource Identifier). reg-id: This refers to the value of a new header field parameter value for the Contact header field. When a UA registers multiple times, each concurrent registration gets a unique reg-id value. instance-id: This specification uses the word instance-id to refer to the value of the "sip.instance" media feature tag in the Contact header field. This is a Uniform Resource Name (URN) that uniquely identifies this specific UA instance. 'ob' Parameter: The 'ob' parameter is a SIP URI parameter which has different meaning depending on context. In a Path header field value it is used by the first edge proxy to indicate that a flow token was added to the URI. In a Contact or Route header field value it indicates that the UA would like other requests in the same dialog routed over the same flow. outbound-proxy-set: A set of SIP URIs (Uniform Resource Identifiers) that represents each of the outbound proxies (often Edge Proxies) with which the UA will attempt to maintain a direct flow. The first URI in the set is often referred to as the primary outbound proxy and the second as the secondary outbound proxy. There is no difference between any of the URIs in this set, nor does the primary/secondary terminology imply that one is preferred over the other. 3. Overview The mechanisms defined in this document are useful in several scenarios discussed below, including the simple co-located registrar and proxy, a User Agent desiring multiple connections to a resource Jennings & Mahy Expires August 27, 2008 [Page 5] Internet-Draft Client Initiated Connections in SIP February 2008 (for redundancy, for example), and a system that uses Edge Proxies. 3.1. Summary of Mechanism The overall approach is fairly simple. Each UA has a unique instance-id that stays the same for this UA even if the UA reboots or is power cycled. Each UA can register multiple times over different connections for the same SIP Address of Record (AOR) to achieve high reliability. Each registration includes the instance-id for the UA and a reg-id label that is different for each flow. The registrar can use the instance-id to recognize that two different registrations both reach the same UA. The registrar can use the reg-id label to recognize whether a UA is creating a new flow or refreshing or replacing an old one, possibly after a reboot or a network failure. When a proxy goes to route a message to a UA for which it has a binding, it can use any one of the flows on which a successful registration has been completed. A failure to deliver a request on a particular flow can be tried again on an alternate flow. Proxies can determine which flows go to the same UA by comparing the instance-id. Proxies can tell that a flow replaces a previously abandoned flow by looking at the reg-id. When sending a dialog-forming request, a UA can also ask its first edge proxy to route subsequent requests in that dialog over the same flow. This is necessary whether the UA has registered or not. UAs can use a simple periodic message as a keep alive mechanism to keep their flow to the proxy or registrar alive. For connection oriented transports such as TCP this is based on carriage-return and line-feed sequences (CRLF), while for transports that are not connection oriented this is accomplished by using a SIP-specific usage profile of STUN (Session Traversal Utilities for NAT) [I-D.ietf-behave-rfc3489bis]. The UA can also ask its first hop proxy to use an specific flow for subsequent messages when sending a dialog-forming request. This allows the UA to setup a subscription dialog for the SIP configuration package [I-D.ietf-sipping-config-framework] before the UA registers. 3.2. Single Registrar and UA In the topology shown below, a single server is acting as both a registrar and proxy. Jennings & Mahy Expires August 27, 2008 [Page 6] Internet-Draft Client Initiated Connections in SIP February 2008 +-----------+ | Registrar | | Proxy | +-----+-----+ | | +----+--+ | User | | Agent | +-------+ User Agents which form only a single flow continue to register normally but include the instance-id as described in Section 4.1. The UA also includes a reg-id parameter which is used to allow the registrar to detect and avoid keeping invalid contacts when a UA reboots or reconnects after its old connection has failed for some reason. For clarity, here is an example. Bob's UA creates a new TCP flow to the registrar and sends the following REGISTER request. REGISTER sip:example.com SIP/2.0 Via: SIP/2.0/TCP 192.168.0.2;branch=z9hG4bK-bad0ce-11-1036 Max-Forwards: 70 From: Bob ;tag=d879h76 To: Bob Call-ID: 8921348ju72je840.204 CSeq: 1 REGISTER Supported: path, outbound Contact: ; reg-id=1; ;+sip.instance="" Content-Length: 0 The registrar challenges this registration to authenticate Bob. When the registrar adds an entry for this contact under the AOR for Bob, the registrar also keeps track of the connection over which it received this registration. The registrar saves the instance-id ("urn:uuid:00000000-0000-1000-8000-000A95A0E128") and reg-id ("1") along with the rest of the Contact header field. If the instance-id and reg-id are the same as a previous registration for the same AOR, the registrar replaces the old Contact URI and flow information. This allows a UA that has rebooted to replace its previous registration for each flow with minimal impact on overall system load. When Alice sends a request to Bob, his authoritative proxy selects Jennings & Mahy Expires August 27, 2008 [Page 7] Internet-Draft Client Initiated Connections in SIP February 2008 the target set. The proxy forwards the request to elements in the target set based on the proxy's policy. The proxy looks at the target set and uses the instance-id to understand if two targets both end up routing to the same UA. When the proxy goes to forward a request to a given target, it looks and finds the flows over which it received the registration. The proxy then forwards the request on that existing flow, instead of resolving the Contact URI using the procedures in RFC 3263 [RFC3263] and trying to form a new flow to that contact. As described in the next section, if the proxy has multiple flows that all go to this UA, the proxy can choose any one of the registration bindings for this AOR that has the same instance-id as the selected UA. 3.3. Multiple Connections from a User Agent There are various ways to deploy SIP to build a reliable and scalable system. This section discusses one such design that is possible with the mechanisms in this specification. Other designs are also possible. In the example system below, the logical outbound proxy/registrar for the domain is running on two hosts that share the appropriate state and can both provide registrar and outbound proxy functionality for the domain. The UA will form connections to two of the physical hosts that can perform the authoritative proxy/registrar function for the domain. Reliability is achieved by having the UA form two TCP connections to the domain. Scalability is achieved by using DNS SRV [RFC2782] to load balance the primary connection across a set of machines that can service the primary connection, and also using DNS SRV to load balance across a separate set of machines that can service the secondary connection. The deployment here requires that DNS is configured with one entry that resolves to all the primary hosts and another entry that resolves to all the secondary hosts. While this introduces additional DNS configuration, the approach works and requires no additional SIP extensions. Note: Approaches which select multiple connections from a single DNS SRV set were also considered, but cannot prevent two connections from accidentally resolving to the same host. The approach in this document does not prevent future extensions, such as the SIP UA configuration framework [I-D.ietf-sipping-config-framework], from adding other ways for a User Agent to discover its outbound-proxy-set. Jennings & Mahy Expires August 27, 2008 [Page 8] Internet-Draft Client Initiated Connections in SIP February 2008 +-------------------+ | Domain | | Logical Proxy/Reg | | | |+-----+ +-----+| ||Host1| |Host2|| |+-----+ +-----+| +---\------------/--+ \ / \ / \ / \ / +------+ | User | | Agent| +------+ The UA is configured with multiple outbound proxy registration URIs. These URIs are configured into the UA through whatever the normal mechanism is to configure the proxy address and AOR in the UA. If the AOR is alice@example.com, the outbound-proxy-set might look something like "sip:primary.example.com" and "sip: secondary.example.com". Note that each URI in the outbound-proxy-set could resolve to several different physical hosts. The administrative domain that created these URIs should ensure that the two URIs resolve to separate hosts. These URIs are handled according to normal SIP processing rules, so mechanisms like SRV can be used to do load balancing across a proxy farm. The domain also needs to ensure that a request for the UA sent to host1 or host2 is then sent across the appropriate flow to the UA. The domain might choose to use the Path header approach (as described in the next section) to store this internal routing information on host1 or host2. When a single server fails, all the UAs that have a flow through it will detect a flow failure and try to reconnect. This can cause large loads on the server. When large numbers of hosts reconnect nearly simultaneously, this is referred to as the avalanche restart problem, and is further discussed in Section 4.5. The multiple flows to many servers help reduce the load caused by the avalanche restart. If a UA has multiple flows, and one of the servers fails, the UA delays the specified time before trying to form a new connection to replace the flow to the server that failed. By spreading out the time used for all the UAs to reconnect to a server, the load on the server farm is reduced. When used in this fashion to achieve high reliability, the operator Jennings & Mahy Expires August 27, 2008 [Page 9] Internet-Draft Client Initiated Connections in SIP February 2008 will need to configure DNS such that the various URIs in the outbound proxy set do not resolve to the same host. Another motivation for maintaining multiple flows between the UA and its registrar is related to multihomed UAs. Such UAs can benefit from multiple connections from different interfaces to protect against the failure of an individual access link. 3.4. Edge Proxies Some SIP deployments use edge proxies such that the UA sends the REGISTER to an Edge Proxy that then forwards the REGISTER to the Registrar. The Edge Proxy includes a Path header [RFC3327] so that when the registrar later forwards a request to this UA, the request is routed through the Edge Proxy. There could be a NAT or firewall between the UA and the Edge Proxy. +---------+ |Registrar| |Proxy | +---------+ / \ / \ / \ +-----+ +-----+ |Edge1| |Edge2| +-----+ +-----+ \ / \ / ----------------------------NAT/FW \ / \ / +------+ |User | |Agent | +------+ These systems can use effectively the same mechanism as described in the previous sections but need to use the Path header. When the Edge Proxy receives a registration, it needs to create an identifier value that is unique to this flow (and not a subsequent flow with the same addresses) and put this identifier in the Path header URI. This identifier has two purposes. First, it allows the Edge Proxy to map future requests back to the correct flow. Second, because the identifier will only be returned if the user authenticates with the registrar successfully, it allows the Edge Proxy to indirectly check the user's authentication information via the registrar. The identifier is placed in the user portion of a loose route in the Path header. If the registration succeeds, the Edge Proxy needs to map Jennings & Mahy Expires August 27, 2008 [Page 10] Internet-Draft Client Initiated Connections in SIP February 2008 future requests that are routed to the identifier value from the Path header, to the associated flow. The term Edge Proxy is often used to refer to deployments where the Edge Proxy is in the same administrative domain as the Registrar. However, in this specification we use the term to refer to any proxy between the UA and the Registrar. For example the Edge Proxy may be inside an enterprise that requires its use and the registrar could be from a service provider with no relationship to the enterprise. Regardless if they are in the same administrative domain, this specification requires that Registrars and Edge proxies support the Path header mechanism in RFC 3327 [RFC3327]. 3.5. Keep alive Technique This document describes three keep alive mechanisms. Each of these mechanisms uses a client-to-server "ping" keep alive and a corresponding server-to-client "pong" message. This ping-pong sequence allows the client, and optionally the server, to tell if its flow is still active and useful for SIP traffic. The server responds to pings by sending pongs. If the client does not receive a pong in response to its ping, it declares the flow dead and opens a new flow in its place. This document also suggests timer values for two of these client keep alive mechanisms. These timer values were chosen to keep most NAT and firewall bindings open, to detect unresponsive servers within 2 minutes, and to prevent the avalanche restart problem. However, the client may choose different timer values to suit its needs, for example to optimize battery life. In some environments, the server can also keep track of the time since a ping was received over a flow to guess the likelihood that the flow is still useful for delivering SIP messages. When the UA detects that a flow has failed or that the flow definition has changed, the UA needs to re-register and will use the back-off mechanism described in Section 4 to provide congestion relief when a large number of agents simultaneously reboot. A keep alive mechanism needs to keep NAT bindings refreshed; for connections, it also needs to detect failure of a connection; and for connectionless transports, it needs to detect flow failures including changes to the NAT public mapping. For connection oriented transports such as TCP and SCTP, this specification describes a keep alive approach based on sending CRLFs. For connectionless transport, such as UDP, this specification describes using STUN [I-D.ietf-behave-rfc3489bis] over the same flow as the SIP traffic to perform the keepalive. Jennings & Mahy Expires August 27, 2008 [Page 11] Internet-Draft Client Initiated Connections in SIP February 2008 UAs are also free to use native transport keep alives, however the UA application may not be able to set these timers on a per-connection basis, and the server certainly cannot make any assumption about what values are used. Use of native transport keep alives is therefore outside the scope of this document. 3.5.1. CRLF Keep-alive Technique This approach can only be used with connection-oriented transports such as TCP or SCTP. The client periodically sends a double-CRLF (the "ping") then waits to receive a single CRLF (the "pong"). If the client does not receive a "pong" within an appropriate amount of time, it considers the flow failed. Sending a CRLF over a connection-oriented transport is backwards compatible (because of requirements in Section 7.5 of RFC 3261), but only implementations which support this specification will respond to a "ping" with a "pong". 3.5.2. STUN Keep alive Technique This approach can only be used for connection-less transports, such as UDP. For connection-less transports, a flow definition could change because a NAT device in the network path reboots and the resulting public IP address or port mapping for the UA changes. To detect this, STUN requests are sent over the same flow that is being used for the SIP traffic. The proxy or registrar acts as a Session Traversal Utilities for NAT (STUN) [I-D.ietf-behave-rfc3489bis] server on the SIP signaling port. Note: The STUN mechanism is very robust and allows the detection of a changed IP address. Many other options were considered, but the SIP Working Group selected the STUN-based approach. Approaches using SIP requests were abandoned because many believed that good performance and full backwards compatibility using this method were mutually exclusive. 4. User Agent Mechanisms 4.1. Instance ID Creation Each UA MUST have an Instance Identifier Uniform Resource Name (URN) [RFC2141] that uniquely identifies the device. Usage of a URN provides a persistent and unique name for the UA instance. It also provides an easy way to guarantee uniqueness within the AOR. This Jennings & Mahy Expires August 27, 2008 [Page 12] Internet-Draft Client Initiated Connections in SIP February 2008 URN MUST be persistent across power cycles of the device. The Instance ID MUST NOT change as the device moves from one network to another. A UA SHOULD create a UUID URN [RFC4122] as its instance-id. The UUID URN allows for non-centralized computation of a URN based on time, unique names (such as a MAC address), or a random number generator. A device like a soft-phone, when first installed, can generate a UUID [RFC4122] and then save this in persistent storage for all future use. For a device such as a hard phone, which will only ever have a single SIP UA present, the UUID can include the MAC address and be generated at any time because it is guaranteed that no other UUID is being generated at the same time on that physical device. This means the value of the time component of the UUID can be arbitrarily selected to be any time less than the time when the device was manufactured. A time of 0 (as shown in the example in Section 3.2) is perfectly legal as long as the device knows no other UUIDs were generated at this time on this device. If a URN scheme other than UUID is used, the UA MUST only use URNs for which an IETF consensus RFC defines how the specific URN needs to be constructed and used in the sip.instance Contact parameter for outbound behavior. To convey its instance-id in both requests and responses, the UA includes a "sip.instance" media feature tag as a UA characteristic [RFC3840] . As described in [RFC3840], this media feature tag will be encoded in the Contact header field as the "+sip.instance" Contact header field parameter. One case where a UA may not want to include the sip.instance media feature tag at all is when it is making an anonymous request or some other privacy concern requires that the UA not reveal its identity. RFC 3840 [RFC3840] defines equality rules for callee capabilities parameters, and according to that specification, the "sip.instance" media feature tag will be compared by case- sensitive string comparison. This means that the URN will be encapsulated by angle brackets ("<" and ">") when it is placed within the quoted string value of the +sip.instance Contact header field parameter. The case-sensitive matching rules apply only to the generic usages defined in RFC 3840 [RFC3840] and in the caller preferences specification [RFC3841]. When the instance ID is used in this specification, it is effectively "extracted" from the value in the "sip.instance" media feature tag. Thus, equality comparisons are performed using the rules for URN equality that are specific to the scheme in the URN. If the element performing the comparisons does not understand the URN scheme, it performs Jennings & Mahy Expires August 27, 2008 [Page 13] Internet-Draft Client Initiated Connections in SIP February 2008 the comparisons using the lexical equality rules defined in RFC 2141 [RFC2141]. Lexical equality could result in two URNs being considered unequal when they are actually equal. In this specific usage of URNs, the only element which provides the URN is the SIP UA instance identified by that URN. As a result, the UA instance MUST provide lexically equivalent URNs in each registration it generates. This is likely to be normal behavior in any case; clients are not likely to modify the value of the instance ID so that it remains functionally equivalent yet lexicographically different from previous registrations. 4.2. Registrations 4.2.1. Initial Registrations At configuration time, UAs obtain one or more SIP URIs representing the default outbound-proxy-set. This specification assumes the set is determined via any of a number of configuration mechanisms, and future specifications can define additional mechanisms such as using DNS to discover this set. How the UA is configured is outside the scope of this specification. However, a UA MUST support sets with at least two outbound proxy URIs and SHOULD support sets with up to four URIs. For each outbound proxy URI in the set, the UA SHOULD send a unique REGISTER in the normal way using this URI as the default outbound proxy. (The UA could limit the number of flows formed to conserve battery power, for example). UAs that support this specification MUST include the outbound option tag in a Supported header field in a REGISTER request. Each of these REGISTER requests will use a unique Call-ID. Forming the route set for the request is outside the scope of this document, but typically results in sending the REGISTER such that the topmost Route header field contains a loose route to the outbound proxy URI. Registration requests, other than those described in Section 4.2.3, MUST include an instance-id media feature tag as specified in Section 4.1. These ordinary registration requests include a distinct reg-id parameter in the Contact header field. Each one of these registrations will form a new flow from the UA to the proxy. The sequence of reg-id values does not have to be sequential but MUST be exactly the same sequence of reg-id values each time the UA instance power cycles or reboots so that the reg-id values will collide with the previously used reg-id values. This is so the registrar can replace the older registrations. Jennings & Mahy Expires August 27, 2008 [Page 14] Internet-Draft Client Initiated Connections in SIP February 2008 The UAC can situationally decide whether to request outbound behavior by including or omitting the 'reg-id' parameter. For example, imagine the outbound-proxy-set contains two proxies in different domains, EP1 and EP2. If an outbound-style registration succeeded for a flow through EP1, the UA might decide to include 'outbound' in its Require header field when registering with EP2, in order to insure consistency. Similarly, if the registration through EP1 did not support outbound, the UA might not register with EP2 at all. The UAC MUST indicate that it supports the Path header [RFC3327] mechanism, by including the 'path' option-tag in a Supported header field value in its REGISTER requests. Other than optionally examining the Path vector in the response, this is all that is required of the UAC to support Path. The UAC examines successful registration responses for the presence of an 'outbound' option-tag in a Require header field value. Presence of this option-tag indicates that the registrar is compliant with this specification, and that any edge proxies which needed to participate are also compliant. If the registrar did not support outbound, the UA may have unintentionally registered an unroutable contact. It is the responsiblity of the UA to remove any inappropriate Contacts. If outbound registration succeeded, as indicated by the presence of the outbound option-tag in the Require header field of a successful registration response, the UA begins sending keepalives as described in Section 4.4. Note that the UA needs to honor 503 (Service Unavailable) responses to registrations as described in RFC 3261 and RFC 3263 [RFC3263]. In particular, implementors should note that when receiving a 503 (Service Unavailable) response with a Retry-After header field, the UA is expected to wait the indicated amount of time and retry the registration. A Retry-After header field value of 0 is valid and indicates the UA is expected to retry the REGISTER immediately. Implementations need to ensure that when retrying the REGISTER, they revisit the DNS resolution results such that the UA can select an alternate host from the one chosen the previous time the URI was resolved. If the registering UA receives a 439 (First Hop Lacks Outbound Support) response to a REGISTER request, it MAY re-attempt registration without an outbound proxy (subject to local policy at the client). If the client has one or more alternate outbound proxies available, it MAY re-attempt registration through such outbound proxies. See Section 11.2 for more information on the 439 Jennings & Mahy Expires August 27, 2008 [Page 15] Internet-Draft Client Initiated Connections in SIP February 2008 response code. 4.2.2. Subsequent REGISTER requests Re-registrations and single Contact de-registrations use the same instance-id and reg-id values as the corresponding initial registration. Re-registrations which merely refresh an existing valid registration SHOULD be sent over the same flow as the original registration. 4.2.3. Non Outbound Registrations A User Agent MUST NOT include a reg-id header parameter in the Contact header field of a registration with a non-zero expiration, if the registering UA is not the same instance as the UA referred to by the target Contact header field. (This practice is occasionally used to install forwarding policy into registrars.) A UAC also MUST NOT include an instance-id or reg-id parameter in a request to unregister all Contacts (a single Contact header field value with the value of "*"). 4.3. Sending Non-REGISTER Requests When a UA is about to send a request, it first performs normal processing to select the next hop URI. The UA can use a variety of techniques to compute the route set and accordingly the next hop URI. Discussion of these techniques is outside the scope of this document. UAs that support this specification SHOULD include the outbound option tag in a Supported header field in a non-Register REGISTER request. The UA performs normal DNS resolution on the next hop URI (as described in RFC 3263 [RFC3263]) to find a protocol, IP address, and port. For protocols that don't use TLS, if the UA has an existing flow to this IP address, and port with the correct protocol, then the UA MUST use the existing connection. For TLS protocols, there MUST also be a match between the host production in the next hop and one of the URIs contained in the subjectAltName in the peer certificate. If the UA cannot use one of the existing flows, then it SHOULD form a new flow by sending a datagram or opening a new connection to the next hop, as appropriate for the transport protocol. If the UA is sending a dialog-forming request, and wants all subsequent requests in the dialog to arrive over the same flow, the UA adds an 'ob' parameter to its Contact header. Typically this is desirable, but it is not necessary for example if the Contact is a GRUU [I-D.ietf-sip-gruu]. The flow used for the request is typically Jennings & Mahy Expires August 27, 2008 [Page 16] Internet-Draft Client Initiated Connections in SIP February 2008 the same flow the UA registered over, but it could be a new flow, for example the initial subcription dialog for the configuration framework [I-D.ietf-sipping-config-framework] needs to exist before registration. Note that if the UA wants a UDP flow to work through NATs or firewalls it still needs to put the 'rport' parameter [RFC3581] in its Via header field value, and send from the port it is prepared to receive on. More general information about NAT traversal in SIP is described in [I-D.ietf-sipping-nat-scenarios]. 4.4. Keep-alives and Detecting Flow Failure The UA needs to detect when a specific flow fails. The UA actively tries to detect failure by periodically sending keep alive messages using one of the techniques described in Section 4.4.1 or Section 4.4.2. If a flow has failed, the UA follows the procedures in Section 4.2 to form a new flow to replace the failed one. When a successful registration response contains the Flow-Timer header field, the value of this header field is the number of seconds the server is prepared to wait without seeing keepalives before it considers the corresponding flow dead. The UA MUST send keepalives at least as often as this number of seconds. If the UA uses the server recommended keepalive frequency it SHOULD send its keepalives so that the interval between each keepalive is randomly distributed between 80% and 100% of the server provided time. For example, it the server suggests 120 seconds, the UA would send each keepalive with a different frequency between 95 and 120 seconds. If no Flow-Timer header field was present in a register response for this flow, the UA can send keepalives at its discretion. The rest of this paragraph provides RECOMMENDED default values for these keepalives. The time between each keep alive request when using non connection based transports such as UDP SHOULD be a random number between 24 and 29 seconds. For connection based transports such as TCP, correct selection of keepalive frequency is primarily a trade- off between battery usage and availability. For devices where power is not a significant concern, the UA SHOULD select a random number between 95 and 120 seconds between keepalives. When battery power is a concern, the UA SHOULD select a random number between 672 and 840 seconds (14 minutes). These times MAY be configurable. To clarify, the random number will be different for each keepalive ping. Note on selection of time values: For UDP, the upper bound of 29 seconds was selected, as many NATs have UDP timeouts as low as 30 seconds. The 24 second lower bound was selected so that after 10 minutes the jitter introduced by different timers will make the Jennings & Mahy Expires August 27, 2008 [Page 17] Internet-Draft Client Initiated Connections in SIP February 2008 keep alive requests unsynchronized to evenly spread the load on the servers. For TCP, the 120 seconds upper bound was chosen based on the idea that for a good user experience, failures normally will be detected in this amount of time and a new connection set up. The 14 minute upper-bound for battery-powered devices was selected based on NATs with TCP timeouts as low as 15 minutes. Operators that wish to change the relationship between load on servers and the expected time that a user might not receive inbound communications will probably adjust this time. The 95 seconds lower bound was chosen so that the jitter introduced will result in a relatively even load on the servers after 30 minutes. The client needs to perform normal RFC 3263 [RFC3263] SIP DNS resolution on the URI from the outbound-proxy-set to pick a transport. Once a transport is selected, the UA selects the keep alive approach that is recommended for that transport. 4.4.1. Keep alive with CRLF This approach MUST only be used with connection oriented transports such as TCP or SCTP. A User Agent that forms flows, checks if the configured URI to which the UA is connecting resolves to a stream-based transport (ex: TCP and TLS over TCP). For this mechanism, the client "ping" is a double-CRLF sequence, and the server "pong" is a single CRLF, as defined in the ABNF below: CRLF = CR LF double-CRLF = CR LF CR LF CR = 0x0d LF = 0x0a The ping and pong need to be sent between SIP messages and cannot be sent in the middle of a SIP message. If sending over TLS, the CRLFs are sent inside the TLS protected channel. If sending over a SigComp [RFC3320] compressed data stream, the CRLF keep alives are sent inside the compressed stream. The double CRLF is considered a single SigComp message. The specific mechanism for representing these characters is an implementation specific matter to be handled by the SigComp compressor at the sending end. If a pong is not received within 10 seconds then the client MUST treat the flow as failed. Clients MUST support this CRLF keep alive. Jennings & Mahy Expires August 27, 2008 [Page 18] Internet-Draft Client Initiated Connections in SIP February 2008 4.4.2. Keep alive with STUN This approach MUST only be used with connection-less transports, such as UDP. A User Agent that forms flows, checks if the configured URI to which the UA is connecting resolve to use the UDP transport. The UA can periodically perform keep alive checks by sending STUN [I-D.ietf-behave-rfc3489bis] Binding Requests over the flow as described in Section 8. Clients MUST support STUN based keep alives. If a STUN Binding Error Response is received, or if no Binding Response is received after 7 retransmissions (16 times the STUN "RTO" timer--RTO is an estimate of round-trip time), the UA considers the flow failed. If the XOR-MAPPED-ADDRESS in the STUN Binding Response changes, the UA MUST treat this event as a failure on the flow. 4.5. Flow Recovery When a flow used for registration (through a particular URI in the outbound-proxy-set) fails, the UA needs to form a new flow to replace the old flow and replace any registrations that were previously sent over this flow. Each new registration MUST have the same reg-id as the registration it replaces. This is done in much the same way as forming a brand new flow as described in Section 4.2; however, if there is a failure in forming this flow, the UA needs to wait a certain amount of time before retrying to form a flow to this particular next hop. The amount of time to wait depends if the previous attempt at establishing a flow was successful. For the purposes of this section, a flow is considered successful if outbound registration succeeded, and if keep alives are in use on this flow, at least one subsequent keep alive response was received. The number of seconds to wait is computed in the following way. If all of the flows to every URI in the outbound proxy set have failed, the base-time is set to 30 seconds; otherwise, in the case where at least one of the flows has not failed, the base-time is set to 90 seconds. The wait time is computed by taking two raised to the power of the number of consecutive registration failures for that URI, and multiplying this by the base time, up to a maximum of 1800 seconds. wait-time = min( max-time, (base-time * (2 ^ consecutive-failures))) These times MAY be configurable in the UA. The three times are: Jennings & Mahy Expires August 27, 2008 [Page 19] Internet-Draft Client Initiated Connections in SIP February 2008 o max-time with a default of 1800 seconds o base-time (if all failed) with a default of 30 seconds o base-time (if all have not failed) with a default of 90 seconds For example, if the base time is 30 seconds, and there were three failures, then the wait time is min(1800,30*(2^3)) or 240 seconds. The delay time is computed by selecting a uniform random time between 50 and 100 percent of the wait time. The UA MUST wait for the value of the delay time before trying another registration to form a new flow for that URI. To be explicitly clear on the boundary conditions: when the UA boots it immediately tries to register. If this fails and no registration on other flows succeed, the first retry happens somewhere between 30 and 60 seconds after the failure of the first registration request. If the number of consecutive-failures is large enough that the maximum of 1800 seconds is reached, the UA will keep trying indefinitely with a random time of 15 to 30 minutes between each attempt. 5. Edge Proxy Mechanisms 5.1. Processing Register Requests When an Edge Proxy receives a registration request with a reg-id header parameter in the Contact header field, it needs to determine if it (the edge proxy) will have to be visited for any subsequent requests sent to the user agent identified in the Contact header field, or not. If the Edge Proxy determines that this is the case, it inserts its URI in a Path header field value as described in RFC 3327 [RFC3327]. If the Edge Proxy is the first SIP node after the UAC, it either MUST store a "flow token" (containing information about the flow from the previous hop) in its Path URI or reject the request. The flow token MUST be an identifier that is unique to this network flow. The flow token MAY be placed in the userpart of the URI. In addition, the first node MUST include an 'ob' URI parameter in its Path header field value. If the Edge Proxy is not the first SIP node after the UAC it MUST NOT place an 'ob' URI parameter in a Path header field value. The Edge Proxy can determine if it is the first hop by examining the Via header field. 5.2. Generating Flow Tokens A trivial but impractical way to satisfy the flow token requirement in Section 5.1 involves storing a mapping between an incrementing counter and the connection information; however this would require the Edge Proxy to keep an infeasible amount of state. It is unclear when this state could be removed and the approach would have problems Jennings & Mahy Expires August 27, 2008 [Page 20] Internet-Draft Client Initiated Connections in SIP February 2008 if the proxy crashed and lost the value of the counter. A stateless example is provided below. A proxy can use any algorithm it wants as long as the flow token is unique to a flow, the flow can be recovered from the token, and the token cannot be modified by attackers. Example Algorithm: When the proxy boots it selects a 20-octet crypto random key called K that only the Edge Proxy knows. A byte array, called S, is formed that contains the following information about the flow the request was received on: an enumeration indicating the protocol, the local IP address and port, the remote IP address and port. The HMAC of S is computed using the key K and the HMAC- SHA1-80 algorithm, as defined in [RFC2104]. The concatenation of the HMAC and S are base64 encoded, as defined in [RFC4648], and used as the flow identifier. When using IPv4 addresses, this will result in a 32-octet identifier. 5.3. Forwarding Non-REGISTER Requests When an Edge Proxy receives a request, it applies normal routing procedures with the following additions. If the Edge Proxy receives a request where the edge proxy is the host in the topmost Route header field value, and the Route header field value contains a flow token, the proxy may need to do additional processing. If the Route header value contains an 'ob' parameter, the Route header was probably copied from the Path header in a registration. If this is the case and the request is a new dialog-forming request, the proxy needs to adjust the route set to insure that subsequent requests in the dialog can be delivered over a valid flow to the UA instance identified by the flow token. A simple approach to satisfy this requirement is for the proxy to add a Record-Route header field value that contains the flow- token, by copying the URI in the Route header minus the 'ob' parameter. Whether the Route header contained an 'ob' parameter or not, next the proxy decodes the flow token and compares the flow in the flow token with the source of the request to determine if this is an "incoming" or "outgoing" request. If the flow in the flow token in the topmost Route header field value matches the source IP address and port of the request, the request is an "outgoing" request. For an "outgoing" request, the edge proxy just removes the Route header and continues processing the request. Otherwise, this is an "incoming" request. For an incoming request, the proxy removes the Route header field value and forwards the request over the 'logical flow' identified by the flow token, that is Jennings & Mahy Expires August 27, 2008 [Page 21] Internet-Draft Client Initiated Connections in SIP February 2008 known to deliver data to the specific target UA instance. For connection-oriented transports, if the flow no longer exists the proxy SHOULD send a 430 (Flow Failed) response to the request. Proxies which used the example algorithm described in this document to form a flow token follow the procedures below to determine the correct flow. Example Algorithm: To decode the flow token, take the flow identifier in the user portion of the URI and base64 decode it, then verify the HMAC is correct by recomputing the HMAC and checking that it matches. If the HMAC is not correct, the proxy SHOULD send a 403 (Forbidden) response. (The proxy could ignore such requests for prevention of denial of service attacks.) If the HMAC is correct then the proxy SHOULD forward the request on the flow that was specified by the information in the flow identifier. If this flow no longer exists, the proxy SHOULD send a 430 (Flow Failed) response to the request. Note that this specification needs mid-dialog requests to be routed over the same flows as those stored in the Path vector from the initial registration, but specific procedures at the edge proxy to ensure that mid-dialog requests are routed over an existing flow are not part of this specification. However, an approach such as having the Edge Proxy add a Record-Route header with a flow token is one way to ensure that mid-dialog requests are routed over the correct flow. The Edge Proxy can use the presence of the "ob" parameter in dialog- forming requests in the UAC's Contact URI (or topmost Route header field) to determine if it should add a flow token. 5.4. Edge Proxy Keep alive Handling All edge proxies compliant with this specification MUST implement support for STUN NAT Keep alives on its SIP UDP ports as described in Section 8. When a server receives a double CRLF sequence on a connection oriented transport such as TCP or SCTP, it MUST immediately respond with a single CRLF over the same connection. The last proxy to forward a successful registration response to a UA MAY include a Flow-Timer header field if the response contains the outbound option-tag in a Require header field value in the response. 6. Registrar Mechanisms: Processing REGISTER Requests This specification updates the definition of a binding in RFC 3261 Jennings & Mahy Expires August 27, 2008 [Page 22] Internet-Draft Client Initiated Connections in SIP February 2008 [RFC3261] Section 10 and RFC 3327 [RFC3327] Section 5.3. Registrars which implement this specification MUST support the Path header mechanism RFC 3327 [RFC3327]. When receiving a REGISTER request, the registrar first checks from its Via header field if the registrar is the first hop or not. If the registrar is not the first hop, it examines the Path header of the request. If the Path header field is missing or it exists but the first URI does not have an 'ob' URI parameter, then outbound processing cannot be applied to the registration. In this case, the following processing applies: if the REGISTER request contains the "outbound" option tag in a "Require" header field, then the registrar MUST respond to the REGISTER request with a 439 (First Hop Lacks Outbound Support) response; otherwise, the registrar MUST ignore the reg-id parameter of the Contact header. See Section 11.2 for more information on the 439 response code. A Contact header field value with an instance-id but no reg-id is valid (this combination can be used in the GRUU [I-D.ietf-sip-gruu] specification), but one with a reg-id but no instance-id is not. If the registrar processes a Contact header field value with a reg-id but no instance-id, it simply ignores the reg-id parameter. If the Contact header contains more than one header field value with a non- zero expiration and a 'reg-id' parameter, the entire registration SHOULD be rejected with a 400 Bad Request response. If the Contact header did not contain a 'reg-id' parameter or if that parameter became ignored (as described above) the registrar MUST NOT include the 'outbound' option-tag in the Require header field of its response. The registrar MUST be prepared to receive, simultaneously for the same AOR, some registrations that use instance-id and reg-id and some registrations that do not. The Registrar MAY be configured with local policy to reject any registrations that do not include the instance-id and reg-id, or with Path header field values that do not contain the 'ob' parameter. If the Contact header field does not contain a '+sip.instance' media feature parameter, the registrar processes the request using the Contact binding rules in RFC 3261 [RFC3261]. When a '+sip.instance' media feature parameter is present in a Contact header field of a REGISTER request (after the Contact header validation as described above), the corresponding binding is between an AOR and the combination of the instance-id (from the +sip.instance media feature parameter) and the value of reg-id parameter if it is present. The registrar MUST store in the binding the Contact URI, all the Contact head field parameters, and any Path header field Jennings & Mahy Expires August 27, 2008 [Page 23] Internet-Draft Client Initiated Connections in SIP February 2008 values. (Even though the Contact URI is not used for binding comparisons, it is still needed by the authoritative proxy to form the target set.) The Registrar MUST include the 'outbound' option- tag (defined in Section 12.2) in a Require header field value in its response to the REGISTER request. If the UAC has a direct flow with the registrar, the registrar MUST store enough information to uniquely identify the network flow over which the request arrived. For common operating systems with TCP, this would typically just be the handle to the file descriptor where the handle would become invalid if the TCP session was closed. For common operating systems with UDP this would typically be the file descriptor for the local socket that received the request, the local interface, and the IP address and port number of the remote side that sent the request. The registrar MAY store this information by adding itself to the Path header field with an appropriate flow token. If the registrar receives a re-registration for a specific combination of AOR, instance-id and reg-id values, the registrar MUST update any information that uniquely identifies the network flow over which the request arrived if that information has changed, and SHOULD update the time the binding was last updated. To be compliant with this specification, registrars which can receive SIP requests directly from a UAC without intervening edge proxies MUST implement the same keep alive mechanisms as Edge Proxies (Section 5.4). 7. Authoritative Proxy Mechanisms: Forwarding Requests When a proxy uses the location service to look up a registration binding and then proxies a request to a particular contact, it selects a contact to use normally, with a few additional rules: o The proxy MUST NOT populate the target set with more than one contact with the same AOR and instance-id at a time. o If a request for a particular AOR and instance-id fails with a 430 (Flow Failed) response, the proxy SHOULD replace the failed branch with another target (if one is available) with the same AOR and instance-id, but a different reg-id. o If the proxy receives a final response from a branch other than a 408 (Request Timeout) or a 430 (Flow Failed) response, the proxy MUST NOT forward the same request to another target representing the same AOR and instance-id. The targeted instance has already provided its response. The proxy uses the next-hop target of the message and the value of Jennings & Mahy Expires August 27, 2008 [Page 24] Internet-Draft Client Initiated Connections in SIP February 2008 any stored Path header field vector in the registration binding to decide how to forward and populate the Route header in the request. If the proxy is colocated with the registrar and stored information about the flow to the UA that created the binding, then the proxy MUST send the request over the same 'logical flow' saved with the binding, since that flow is known to deliver data to the specific target UA instance's network flow that was saved with the binding. Typically this means that for TCP, the request is sent on the same TCP socket that received the REGISTER request. For UDP, the request is sent from the same local IP address and port over which the registration was received, to the same IP address and port from which the REGISTER was received. If a proxy or registrar receives information from the network that indicates that no future messages will be delivered on a specific flow, then the proxy MUST invalidate all the bindings in the target set that use that flow (regardless of AOR). Examples of this are a TCP socket closing or receiving a destination unreachable ICMP error on a UDP flow. Similarly, if a proxy closes a file descriptor, it MUST invalidate all the bindings in the target set with flows that use that file descriptor. 8. STUN Keep alive Processing This section describes changes to the SIP transport layer that allow SIP and STUN [I-D.ietf-behave-rfc3489bis] Binding Requests to be mixed over the same flow. This constitues a new STUN usage. The STUN messages are used to verify that connectivity is still available over a UDP flow, and to provide periodic keep alives. Note that these STUN keep alives are always sent to the next SIP hop. STUN messages are not delivered end-to-end. The only STUN messages required by this usage are Binding Requests, Binding Responses, and Binding Error Responses. The UAC sends Binding Requests over the same UDP flow that is used for sending SIP messages. These Binding Requests do not require any STUN attributes except the XOR-MAPPED-ADDRESS and never use any form of authentication. The UAS, proxy, or registrar responds to a valid Binding Request with a Binding Response which MUST include the XOR- MAPPED-ADDRESS attribute. If a server compliant to this section receives SIP requests on a given interface and UDP port, it MUST also provide a limited version of a STUN server on the same interface and UDP port. Jennings & Mahy Expires August 27, 2008 [Page 25] Internet-Draft Client Initiated Connections in SIP February 2008 It is easy to distinguish STUN and SIP packets sent over UDP, because the first octet of a STUN Binding method has a value of 0 or 1 while the first octet of a SIP message is never a 0 or 1. Because sending and receiving binary STUN data on the same ports used for SIP is a significant and non-backwards compatible change to RFC 3261, this section requires a number of checks before sending STUN messages to a SIP node. If a SIP node sends STUN requests (for example due to incorrect configuration) despite these warnings, the node could be blacklisted for UDP traffic. A SIP node MUST NOT send STUN requests over a flow unless it has an explicit indication that the target next hop SIP server claims to support this specification. Note that UACs MUST NOT use an ambiguous configuration option such as "Work through NATs?" or "Do Keep alives?" to imply next hop STUN support. Typically, a SIP node first sends a SIP request and waits to receive a 200-class response over a flow to a new target destination, before sending any STUN messages. When scheduled for the next NAT refresh, the SIP node sends a STUN request to the target. Once a flow is established, failure of a STUN request (including its retransmissions) is considered a failure of the underlying flow. For SIP over UDP flows, if the XOR-MAPPED-ADDRESS returned over the flow changes, this indicates that the underlying connectivity has changed, and is considered a flow failure. The SIP keep alive STUN usage requires no backwards compatibility with RFC 3489 [RFC3489]. 8.1. Use with Sigcomp When STUN is used together with SigComp [RFC3320] compressed SIP messages over the same flow,the STUN messages are simply sent uncompressed, "outside" of SigComp. This is supported by multiplexing STUN messages with SigComp messages by checking the two topmost bits of the message. These bits are always one for SigComp, or zero for STUN. All SigComp messages contain a prefix (the five most-significant bits of the first byte are set to one) that does not occur in UTF-8 [RFC3629] encoded text messages, so for applications which use this encoding (or ASCII encoding) it is possible to multiplex uncompressed application messages and SigComp messages on the same UDP port. Jennings & Mahy Expires August 27, 2008 [Page 26] Internet-Draft Client Initiated Connections in SIP February 2008 The most significant two bits of every STUN Binding method are both zeroes. This, combined with the magic cookie, aids in differentiating STUN packets from other protocols when STUN is multiplexed with other protocols on the same port. 9. Example Message Flow Below is an example message flow illustrating most of the concepts discussed in this specification. In many cases, Via, Content-Length and Max-Forwards headers are omitted for brevity and readability. In the first part of this example message flow, Bob's UA sends a SUBSCRIBE request for the UA profile configuration package. This request is a poll (Expires is zero). After receiving the NOTIFY request, Bob's UA fetches the external configuration using HTTPS (not shown) and obtains a configuration file which contains the outbound- proxy-set "sip:ep1.example.com;lr" and "sip:ep2.example.com;lr. [----example.com domain-------------------------] Bob EP1 EP2 Proxy Config | | | | | 1)|SUBSCRIBE->| | | | 2)| |---SUBSCRIBE Event: ua-profile ->| 3)| |<--200 OK -----------------------| 4)|<--200 OK--| | | | 5)| |<--NOTIFY------------------------| 6)|<--NOTIFY--| | | | 7)|---200 OK->| | | | 8)| |---200 OK ---------------------->| | | | | | Example Message #1: SUBSCRIBE sip:00000000-0000-1000-8000-AABBCCDDEEFF@example.com SIP/2.0 Via: SIP/2.0/TCP 192.168.1.2;branch=z9hG4bKnlsdkdj2 Max-Forwards: 70 From: ;tag=23324 To: Call-ID: nSz1TWN54x7My0GvpEBj CSeq: 1 SUBSCRIBE Event: ua-profile ;profile-type=device ;vendor="example.com";model="uPhone";version="1.1" Expires: 0 Supported: path, outbound Accept: message/external-body, application/x-uPhone-config Contact: ;+sip.instance="" Jennings & Mahy Expires August 27, 2008 [Page 27] Internet-Draft Client Initiated Connections in SIP February 2008 Content-Length: 0 In message #2, EP1 adds the following Record-Route header: Record-Route: In message #5, the configuration server sends a NOTIFY with an external URL for Bob to fetch his configuration. The NOTIFY has a Subscription-State header that ends the subscription. Message #5 NOTIFY sip:192.168.1.2;transport=tcp;ob SIP/2.0 Via: SIP/2.0/TCP 192.0.2.5;branch=z9hG4bKn81dd2 Max-Forwards: 70 To: ;tag=23324 From: ;tag=0983 Call-ID: nSz1TWN54x7My0GvpEBj CSeq: 1 NOTIFY Route: Subscription-State: terminated;reason=timeout Event: ua-profile Content-Type: message/external-body; access-type="URL" ;expiration="Thu, 01 Jan 2009 09:00:00 UTC" ;URL="http://example.com/uPhone.cfg" ;size=9999;hash=10AB568E91245681AC1B Content-Length: 0 EP1 receives this NOTIFY request, strips off the Route header, extracts the flow-token, calculates the correct flow and forwards the request (Message #6) over that flow to Bob. Bob's UA fetches the configuration file. Now that Bob's UA is configured with the outbound-proxy-set, Bob's UA sends REGISTER requests through each edge proxy in the set. Once the registrations succeed, Bob's UA begins sending CRLF keepalives about every 2 minutes. Jennings & Mahy Expires August 27, 2008 [Page 28] Internet-Draft Client Initiated Connections in SIP February 2008 Bob EP1 EP2 Proxy Alice | | | | | 9)|-REGISTER->| | | | 10)| |---REGISTER-->| | 11)| |<----200 OK---| | 12)|<-200 OK---| | | | 13)|----REGISTER---->| | | 14)| | |--REG-->| | 15)| | |<-200---| | 16)|<----200 OK------| | | | | | | | | about 120 seconds later... | | | | | | 17)|--2CRLF--->| | | | 18)|<--CRLF----| | | | 19)|------2CRLF----->| | | 20)|<------CRLF------| | | | | | | | In message #9, Bob's UA sends its first registration through the first edge proxy in the outbound-proxy-set by including a loose route. The UA includes an instance-id and reg-id in its Contact header field value. Note the option-tags in the Supported header. Message #9 REGISTER sip:example.com SIP/2.0 Via: SIP/2.0/TCP 192.168.1.2;branch=z9hG4bKnashds7 Max-Forwards: 70 From: Bob ;tag=7F94778B653B To: Bob Call-ID: 16CB75F21C70 CSeq: 1 REGISTER Supported: path, outbound Route: Contact: ;reg-id=1 ;+sip.instance="" Content-Length: 0 Message #10 is similar. EP1 removes the Route header field value, decrements Max-Forwards, and adds its Via header field value. Since EP1 is the first edge proxy, it adds a Path header with a flow token and includes the 'ob' parameter. Path: Since the response to the REGISTER (message #11) contains the outbound option-tag in the Require header field, Bob's UA will know that the registrar used outbound binding rules. The response also Jennings & Mahy Expires August 27, 2008 [Page 29] Internet-Draft Client Initiated Connections in SIP February 2008 contains the currently active Contacts, the Path for the current registration. SIP/2.0 200 OK Via: SIP/2.0/TCP 192.0.2.15;branch=z9hG4bKnuiqisi Via: SIP/2.0/TCP 192.168.1.2;branch=z9hG4bKnashds7 From: Bob ;tag=7F94778B653B To: Bob ;tag=6AF99445E44A Call-ID: 16CB75F21C70 CSeq: 1 REGISTER Supported: path, outbound Require: outbound Contact: ;reg-id=1;expires=3600 ;+sip.instance="" Path: Content-Length: 0 The second registration through EP2 (message #13) is similar other than the Call-ID has changed, the reg-id is 2, and the Route header goes through EP2. REGISTER sip:example.com SIP/2.0 Via: SIP/2.0/TCP 192.168.1.2;branch=z9hG4bKnqr9bym Max-Forwards: 70 From: Bob ;tag=755285EABDE2 To: Bob Call-ID: E05133BD26DD CSeq: 1 REGISTER Supported: path, outbound Route: Contact: ;reg-id=2 ;+sip.instance="" Content-Length: 0 Likewise in message #14, EP2 adds a Path header with flow token and 'ob' parameter. Path: Message #16 tells Bob's UA that outbound registration was successful, and shows both Contacts. Note that only the Path corresponding to the current registration is returned. Jennings & Mahy Expires August 27, 2008 [Page 30] Internet-Draft Client Initiated Connections in SIP February 2008 SIP/2.0 200 OK Via: SIP/2.0/TCP 192.168.1.2;branch=z9hG4bKnqr9bym From: Bob ;tag=755285EABDE2 To: Bob ;tag=49A9AD0B3F6A Call-ID: E05133BD26DD Supported: path, outbound Require: outbound CSeq: 1 REGISTER Contact: ;reg-id=1;expires=3600 ;+sip.instance="" Contact: ;reg-id=2;expires=3600 ;+sip.instance="" Path: Content-Length: 0 A bit later, EP1 crashes and reboots. Before Bob's UA notices that its flow to EP1 is no longer responding, Alice calls Bob. Bob's authoritative proxy first tries the flow to EP1, but EP1 no longer has a flow to Bob so it responds with a 430 Flow Failed response. The proxy removes the stale registration and tries the next binding for the same instance. Bob EP1 EP2 Proxy Alice | | | | | | CRASH X | | | | Reboot | | | | | | | | 21)| | | |<-INVITE-| 22)| |<---INVITE----| | 23)| |----430------>| | 24)| | |<-INVITE| | 25)|<---INVITE-------| | | 26)|----200 OK------>| | | 27)| | |200 OK->| | 28)| | | |-200 OK->| 29)| | |<----------ACK----| 30)|<---ACK----------| | | | | | | | 31)| | |<----------BYE----| 32)|<---BYE----------| | | 33)|----200 OK------>| | | 34)| | |--------200 OK--->| | | | | | Jennings & Mahy Expires August 27, 2008 [Page 31] Internet-Draft Client Initiated Connections in SIP February 2008 Message #21 INVITE sip:bob@example.com SIP/2.0 To: Bob From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE Bob's proxy rewrites the Request-URI to the Contact URI used in Bob's registration, and places the path for one of the registrations towards Bob's UA instance into a Route header field. This Route goes through EP1. Message #22 INVITE sip:bob@192.168.1.2;transport=tcp SIP/2.0 To: Bob From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE Route: Since EP1 just rebooted, it does not have the flow described in the flow token. It returns a 430 Flow Failed response. Message #23 SIP/2.0 430 Flow Failed To: Bob From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE The proxy deletes the binding for this path and tries to forward the INVITE again, this time with the path through EP2. Message #24 INVITE sip:bob@192.168.1.2;transport=tcp SIP/2.0 To: Bob From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE Route: In message #25, EP2 needs to add a Record-Route header field value, so that any subsequent in-dialog messages from Alice's UA arrive at Bob's UA. EP2 can determine it needs to Record-Route since the request is a dialog-forming request and the Route header contained a flow token and an 'ob' parameter. This Record-Route information is passed back to Alice's UA in the responses (messages #26, 27, and 28) Jennings & Mahy Expires August 27, 2008 [Page 32] Internet-Draft Client Initiated Connections in SIP February 2008 Message #25 INVITE sip:bob@192.168.1.2;transport=tcp SIP/2.0 To: Bob From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE Record-Route: Message #26 SIP/2.0 200 OK To: Bob ;tag=skduk2 From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 INVITE Record-Route: At this point, both UAs have the correct route-set for the dialog. Any subsequent requests in this dialog will route correctly. For example, the ACK request in message #29 is sent form Alice's UA directly to EP2. The BYE request in message #31 uses the same route- set. Message #29 ACK sip:bob@192.168.1.2;transport=tcp SIP/2.0 To: Bob ;tag=skduk2 From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 1 ACK Route: Message #31 BYE sip:bob@192.168.1.2;transport=tcp SIP/2.0 To: Bob ;tag=skduk2 From: Alice ;tag=02935 Call-ID: klmvCxVWGp6MxJp2T2mb CSeq: 2 BYE Route: Somewhat later, Bob's UA sends keepalives to both its edge proxies, but it discovers that the flow with EP1 failed. Bob's UA re- registers through EP1 using the same reg-id and Call-ID it previously used. Jennings & Mahy Expires August 27, 2008 [Page 33] Internet-Draft Client Initiated Connections in SIP February 2008 Bob EP1 EP2 Proxy Alice | | | | | 35)|------2CRLF----->| | | 36)|<------CRLF------| | | 37)|--2CRLF->X | | | | | | | | | 38)|-REGISTER->| | | | 39)| |---REGISTER-->| | 40)| |<----200 OK---| | 41)|<-200 OK---| | | | | | | | | Message #38 REGISTER sip:example.com SIP/2.0 From: Bob ;tag=7F94778B653B To: Bob Call-ID: 16CB75F21C70 CSeq: 2 REGISTER Supported: path, outbound Route: Contact: ;reg-id=1 ;+sip.instance="" In message #39, EP1 inserts a Path header with a new flow token: Path: Finally, Bob makes an outgoing call to Alice. Bob's UA includes an 'ob' parameter in its Contact URI in message #42. EP1 adds a Record- Route with a flow-token in message #43. The route-set is returned to Bob in the response (messages #45, 46, and 47) and either Bob or Alice can send in-dialog requests. Jennings & Mahy Expires August 27, 2008 [Page 34] Internet-Draft Client Initiated Connections in SIP February 2008 Bob EP1 EP2 Proxy Alice | | | | | 42)|--INVITE-->| | | | 43)| |---INVITE---->| | 44)| | | |-INVITE->| 45)| | | |<--200---| 46)| |<----200 OK---| | 47)|<-200 OK---| | | | 48)|--ACK----->| | | | 49)| |-----ACK--------------->| | | | | | 50)|-- BYE---->| | | | 51)| |-----------BYE--------->| 52)| |<----------200 OK-------| 53)|<--200 OK--| | | | | | | | | Message #42 INVITE sip:alice@a.example SIP/2.0 From: Bob ;tag=ldw22z To: Alice Call-ID: 95KGsk2V/Eis9LcpBYy3 CSeq: 1 INVITE Route: Contact: In message #43, EP1 adds the following Record-Route header. Record-Route: When EP1 receives the BYE (message #50) from Bob's UA, it can tell that the request is an "outgoing" request (since the source of the request matches the flow in the flow token) and simply deletes its Route header field value and forwards the request on to Alice's UA. Message #50 BYE sip:alice@a.example SIP/2.0 From: Bob ;tag=ldw22z To: Alice ;tag=plqus8 Call-ID: 95KGsk2V/Eis9LcpBYy3 CSeq: 2 BYE Route: Contact: Jennings & Mahy Expires August 27, 2008 [Page 35] Internet-Draft Client Initiated Connections in SIP February 2008 10. Grammar This specification defines a new header field, new Contact header field parameters, reg-id and +sip.instance. The grammar includes the definitions from RFC 3261 [RFC3261] and includes the definition of uric from RFC 3986 [RFC3986]. Note: The "=/" syntax used in this ABNF indicates an extension of the production on the left hand side. The ABNF[RFC5234] is: message-header =/ Flow-Timer Flow-Timer = "Flow-Timer" HCOLON 1*DIGIT contact-params =/ c-p-reg / c-p-instance c-p-reg = "reg-id" EQUAL 1*DIGIT ; 1 to (2**31 - 1) c-p-instance = "+sip.instance" EQUAL LDQUOT "<" instance-val ">" RDQUOT instance-val = *uric ; defined in RFC 3986 The value of the reg-id MUST NOT be 0 and MUST be less than 2**31. 11. New Response Codes 11.1. Definition of 430 Flow Failed response code This specification defines a new SIP response code '430 Flow Failed'. This response code is used by an Edge Proxy to indicate to the Authoritative Proxy that a specific flow to a UA instance has failed. Other flows to the same instance could still succeed. The Authoritative Proxy SHOULD attempt to forward to another target (flow) with the same instance-id and AOR. 11.2. Definition of 439 First Hop Lacks Outbound Support response This specification defines a new SIP response code '439 First Hop Lacks Outbound Support'. This response code is used by a registrar to indicate that it supports the 'outbound' feature described in this specifcation, but that the first outbound proxy that the user is attempting to register through does not. Note that this response code is only appropriate in the case that the registering user agent is mandating outbound processing by including the 'outbound' option Jennings & Mahy Expires August 27, 2008 [Page 36] Internet-Draft Client Initiated Connections in SIP February 2008 tag in a 'Require' header field. Proxies MUST NOT send a 439 response to any requests that don't contain an 'outbound' option tag in a 'Require' header field. 12. IANA Considerations 12.1. Flow-Timer Header Field This specification defines a new SIP header field "Flow-Timer". RFC Number: RFC XXXX Header Field Name: Flow-Timer Compact Form: none [NOTE TO RFC Editor: Please replace AAAA with the RFC number of this specification.] 12.2. 'reg-id' Contact Header Field Parameter This specification defines a new Contact header field parameter called reg-id in the "Header Field Parameters and Parameter Values" sub-registry as per the registry created by [RFC3968]. The required information is: Header Field Parameter Name Predefined Reference Values ____________________________________________________________________ Contact reg-id No [RFC AAAA] [NOTE TO RFC Editor: Please replace AAAA with the RFC number of this specification.] 12.3. SIP/SIPS URI Parameters This specification augments the "SIP/SIPS URI Parameters" sub- registry as per the registry created by [RFC3969]. The required information is: Parameter Name Predefined Values Reference ____________________________________________ ob No [RFC AAAA] [NOTE TO RFC Editor: Please replace AAAA with the RFC number of this specification.] Jennings & Mahy Expires August 27, 2008 [Page 37] Internet-Draft Client Initiated Connections in SIP February 2008 12.4. SIP Option Tag This specification registers a new SIP option tag, as per the guidelines in Section 27.1 of RFC 3261. Name: outbound Description: This option-tag is used to identify UAs and Registrars which support extensions for Client Initiated Connections. A UA places this option in a Supported header to communicate its support for this extension. A Registrar places this option-tag in a Require header to indicate to the registering User Agent that the Registrar used registrations using the binding rules defined in this extension. 12.5. Response Codes This section registers two new SIP Response Codes, as per the guidelines in Section 27.4 of RFC 3261. 12.5.1. 430 Response Code Code: 430 Default Reason Phrase: Flow Failed Reference: This document 12.5.2. 439 Response Code Code: 439 Default Reason Phrase: First Hop Lacks Outbound Support Reference: This document 12.6. Media Feature Tag This section registers a new media feature tag, per the procedures defined in RFC 2506 [RFC2506]. The tag is placed into the sip tree, which is defined in RFC 3840 [RFC3840]. Media feature tag name: sip.instance ASN.1 Identifier: New assignment by IANA. Summary of the media feature indicated by this tag: This feature tag contains a string containing a URN that indicates a unique identifier associated with the UA instance registering the Contact. Values appropriate for use with this feature tag: String. The feature tag is intended primarily for use in the following Jennings & Mahy Expires August 27, 2008 [Page 38] Internet-Draft Client Initiated Connections in SIP February 2008 applications, protocols, services, or negotiation mechanisms: This feature tag is most useful in a communications application, for describing the capabilities of a device, such as a phone or PDA. Examples of typical use: Routing a call to a specific device. Related standards or documents: RFC XXXX [[Note to IANA: Please replace XXXX with the RFC number of this specification.]] Security Considerations: This media feature tag can be used in ways which affect application behaviors. For example, the SIP caller preferences extension [RFC3841] allows for call routing decisions to be based on the values of these parameters. Therefore, if an attacker can modify the values of this tag, they might be able to affect the behavior of applications. As a result, applications which utilize this media feature tag SHOULD provide a means for ensuring its integrity. Similarly, this feature tag should only be trusted as valid when it comes from the user or user agent described by the tag. As a result, protocols for conveying this feature tag SHOULD provide a mechanism for guaranteeing authenticity. 13. Security Considerations One of the key security concerns in this work is making sure that an attacker cannot hijack the sessions of a valid user and cause all calls destined to that user to be sent to the attacker. Note that the intent is not to prevent existing active attacks on SIP UDP and TCP traffic, but to insure that no new attacks are added by introducing the outbound mechanism. The simple case is when there are no edge proxies. In this case, the only time an entry can be added to the routing for a given AOR is when the registration succeeds. SIP already protects against attackers being able to successfully register, and this scheme relies on that security. Some implementers have considered the idea of just saving the instance-id without relating it to the AOR with which it registered. This idea will not work because an attacker's UA can impersonate a valid user's instance-id and hijack that user's calls. The more complex case involves one or more edge proxies. When a UA sends a REGISTER request through an Edge Proxy on to the registrar, the Edge Proxy inserts a Path header field value. If the registration is successfully authenticated, the registrar stores the value of the Path header field. Later when the registrar forwards a request destined for the UA, it copies the stored value of the Path Jennings & Mahy Expires August 27, 2008 [Page 39] Internet-Draft Client Initiated Connections in SIP February 2008 header field into the Route header field of the request and forwards the request to the Edge Proxy. The only time an Edge Proxy will route over a particular flow is when it has received a Route header that has the flow identifier information that it has created. An incoming request would have gotten this information from the registrar. The registrar will only save this information for a given AOR if the registration for the AOR has been successful; and the registration will only be successful if the UA can correctly authenticate. Even if an attacker has spoofed some bad information in the Path header sent to the registrar, the attacker will not be able to get the registrar to accept this information for an AOR that does not belong to the attacker. The registrar will not hand out this bad information to others, and others will not be misled into contacting the attacker. The Security Considerations discussed in [RFC3261] and [RFC3327] are also relevant to this document. For the security considerations of generating flow tokens, please also see Section 5.2. A discussion of preventing the avalanche restart problem is in Section 4.5. This document does not change the mandatory to implement security mechanisms in SIP. User Agents are already required to implement Digest authentication while support of TLS is recommended; proxy servers are already required to implement Digest and TLS. 14. Operational Notes on Transports This entire section is non-normative. RFC 3261 requires proxies, registrars, and User Agents to implement both TCP and UDP but deployments can chose which transport protocols they want to use. Deployments need to be careful in choosing what transports to use. Many SIP features and extensions, such as large presence notification bodies, result in SIP requests that can be too large to be reasonably transported over UDP. RFC 3261 states that when a request is too large for UDP, the device sending the request attempts to switch over to TCP. No known deployments currently use this feature but it is important to note that when using outbound, this will only work if the UA has formed both UDP and TCP outbound flows. This specification allows the UA to do so but in most cases it will probably make more sense for the UA to form a TCP outbound connection only, rather than forming both UDP and TCP flows. One of the key reasons that many deployments choose not to use TCP has to do with the difficulty of building proxies that can maintain a very large number of active TCP connections. Many deployments today use SIP in such a way that the messages are small enough that they work Jennings & Mahy Expires August 27, 2008 [Page 40] Internet-Draft Client Initiated Connections in SIP February 2008 over UDP but they can not take advantage of all the functionality SIP offers. Deployments that use only UDP outbound connections are going to fail with sufficiently large SIP messages. 15. Requirements This specification was developed to meet the following requirements: 1. Must be able to detect that a UA supports these mechanisms. 2. Support UAs behind NATs. 3. Support TLS to a UA without a stable DNS name or IP address. 4. Detect failure of a connection and be able to correct for this. 5. Support many UAs simultaneously rebooting. 6. Support a NAT rebooting or resetting. 7. Minimize initial startup load on a proxy. 8. Support architectures with edge proxies. 16. Changes Note to RFC Editor: Please remove this whole section. 16.1. Changes from 11 Version Added 439 response code to handle "Require: outbound" with first outbound proxy that doesn't insert ";ob". 16.2. Changes from 09 Version Make outbound consistent with the latest version of STUN 3489bis draft. The STUN keepalive section of outbound is now a STUN usage (much less formal). Fixed references. 16.3. Changes from 08 Version UAs now include the 'ob' parameter in their Contact header for non- REGISTER requests, as a hint to the Edge Proxy (so the EP can Record- Route with a flow-token for example). Switched to CRLF for keepalives of connection-oriented transports after brutal consensus at IETF 68. Added timed-keepalive parameter and removed the unnecessary keep-tcp param, per consensus at IETF68. Jennings & Mahy Expires August 27, 2008 [Page 41] Internet-Draft Client Initiated Connections in SIP February 2008 Removed example "Algorithm 1" which only worked over SIPS, per consensus at IETF68. Deleted text about probing and validating with options, per consensus at IETF68. Deleted provision for waiting 120 secs before declaring flow stable, per consensus at IETF68. fixed example UUIDs 16.4. Changes from 07 Version Add language to show the working group what adding CRLF keepalives would look like. Changed syntax of keep-alive=stun to keep-stun so that it was easier to support multiple tags in the same URI. 16.5. Changes from 06 Version Added the section on operational selection of transports. Fixed various editorial typos. Put back in requirement flow token needs to be unique to flow as it had accidentally been dropped in earlier version. This did not change any of the flow token algorithms. Reordered some of the text on STUN keepalive validation to make it clearer to implementors. Did not change the actual algorithm or requirements. Added note to explain how if the proxy changes, the revalidation will happen. 16.6. Changes from 05 Version Mention the relevance of the 'rport' parameter. Change registrar verification so that only first-hop proxy and the registrar need to support outbound. Other intermediaries in between do not any more. Relaxed flow-token language slightly. Instead of flow-token saving specific UDP address/port tuples over which the request arrived, make language fuzzy to save token which points to a 'logical flow' that is known to deliver data to that specific UA instance. Added comment that keep-stun could be added to Path. Jennings & Mahy Expires August 27, 2008 [Page 42] Internet-Draft Client Initiated Connections in SIP February 2008 Added comment that battery concerns could motivate longer TCP keepalive intervals than the defaults. Scrubbed document for avoidable lowercase may, should, and must. Added text about how Edge Proxies could determine they are the first hop. 16.7. Changes from 04 Version Moved STUN to a separate section. Reference this section from within the relevant sections in the rest of the document. Add language clarifying that UA MUST NOT send STUN without an explicit indication the server supports STUN. Add language describing that UA MUST stop sending STUN if it appears the server does not support it. Defined a 'sip-stun' option tag. UAs can optionally probe servers for it with OPTIONS. Clarified that UAs SHOULD NOT put this in a Proxy-Require. Explain that the first-hop MUST support this option- tag. Clarify that SIP/STUN in TLS is on the "inside". STUN used with Sigcomp-compressed SIP is "outside" the compression layer for UDP, but wrapped inside the well-known shim header for TCP-based transports. Clarify how to decide what a consecutive registration timer is. Flow must be up for some time (default 120 seconds) otherwise previous registration is not considered successful. Change UAC MUST-->SHOULD register a flow for each member of outbound- proxy-set. Reworded registrar and proxy in some places (introduce the term "Authoritative Proxy"). Loosened restrictions on always storing a complete Path vector back to the registrar/authoritative proxy if a previous hop in the path vector is reachable. Added comment about re-registration typically happening over same flow as original registration. Changed 410 Gone to new response code 430 Flow Failed. Was going to change this to 480 Temporarily Unavailable. Unfortunately this would Jennings & Mahy Expires August 27, 2008 [Page 43] Internet-Draft Client Initiated Connections in SIP February 2008 mean that the authoritative proxy deletes all flows of phones who use 480 for Do Not Disturb. Oops! Restored sanity by restoring text which explains that registrations with the same reg-id replace the old registration. Added text about the 'ob' parameter which is used in Path header field URIs to make sure that the previous proxy that added a Path understood outbound processing. The registrar doesn't include Supported: outbound unless it could actually do outbound processing (ex: any Path headers have to have the 'ob' parameter). Added some text describing what a registration means when there is an instance-id, but no reg-id. 16.8. Changes from 03 Version Added non-normative text motivating STUN vs. SIP PING, OPTIONS, and Double CRLF. Added discussion about why TCP Keepalives are not always available. Explained more clearly that outbound-proxy-set can be "configured" using any current or future, manual or automatic configuration/ discovery mechanism. Added a sentence which prevents an Edge Proxy from forwarding back over the flow over which the request is received if the request happens to contain a flow token for that flow. This was an oversight. Updated example message flow to show a fail-over example using a new dialog-creating request instead of a mid-dialog request. The old scenario was leftover from before the outbound / gruu reorganization. Fixed tags, Call-IDs, and branch parameters in the example messages. Made the ABNF use the "=/" production extension mechanism recommended by Bill Fenner. Added a table in an appendix expanding the default flow recovery timers. Incorporated numerous clarifications and rewordings for better comprehension. Fixed many typos and spelling steaks. Jennings & Mahy Expires August 27, 2008 [Page 44] Internet-Draft Client Initiated Connections in SIP February 2008 16.9. Changes from 02 Version Removed Double CRLF Keepalive Changed ;sip-stun syntax to ;keepalive=stun Fixed incorrect text about TCP keepalives. 16.10. Changes from 01 Version Moved definition of instance-id from GRUU[I-D.ietf-sip-gruu] draft to this draft. Added tentative text about Double CRLF Keepalive Removed pin-route stuff Changed the name of "flow-id" to "reg-id" Reorganized document flow Described the use of STUN as a proper STUN usage Added 'outbound' option-tag to detect if registrar supports outbound 16.11. Changes from 00 Version Moved TCP keepalive to be STUN. Allowed SUBSCRIBE to create flow mappings. Added pin-route option tags to support this. Added text about updating dialog state on each usage after a connection failure. 17. Acknowledgments Francois Audet acted as document shepherd for this draft, tracking hundreds of comments and incorporating many grammatical fixes as well as prodding the editors to "get on with it". Jonathan Rosenberg, Erkki Koivusalo, and Byron Campben provided many comments and useful text. Dave Oran came up with the idea of using the most recent registration first in the proxy. Alan Hawrylyshen co-authored the draft that formed the initial text of this specification. Additionally, many of the concepts here originated at a connection reuse meeting at IETF 60 that included the authors, Jon Peterson, Jonathan Rosenberg, Alan Hawrylyshen, and Paul Kyzivat. The TCP Jennings & Mahy Expires August 27, 2008 [Page 45] Internet-Draft Client Initiated Connections in SIP February 2008 design team consisting of Chris Boulton, Scott Lawrence, Rajnish Jain, Vijay K. Gurbani, and Ganesh Jayadevan provided input and text. Nils Ohlmeier provided many fixes and initial implementation experience. In addition, thanks to the following folks for useful comments: Francois Audet, Flemming Andreasen, Mike Hammer, Dan Wing, Srivatsa Srinivasan, Dale Worely, Juha Heinanen, Eric Rescorla, Lyndsay Campbell, Christer Holmberg, Kevin Johns, Jeroen van Bemmel, and Derek MacDonald. 18. References 18.1. Normative References [I-D.ietf-behave-rfc3489bis] Rosenberg, J., Mahy, R., Matthews, P., and D. Wing, "Session Traversal Utilities for (NAT) (STUN)", draft-ietf-behave-rfc3489bis-15 (work in progress), February 2008. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2141] Moats, R., "URN Syntax", RFC 2141, May 1997. [RFC2506] Holtman, K., Mutz, A., and T. Hardie, "Media Feature Tag Registration Procedure", BCP 31, RFC 2506, March 1999. [RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, June 2002. [RFC3263] Rosenberg, J. and H. Schulzrinne, "Session Initiation Protocol (SIP): Locating SIP Servers", RFC 3263, June 2002. [RFC3327] Willis, D. and B. Hoeneisen, "Session Initiation Protocol (SIP) Extension Header Field for Registering Non-Adjacent Contacts", RFC 3327, December 2002. [RFC3489] Rosenberg, J., Weinberger, J., Huitema, C., and R. Mahy, "STUN - Simple Traversal of User Datagram Protocol (UDP) Through Network Address Translators (NATs)", RFC 3489, March 2003. [RFC3581] Rosenberg, J. and H. Schulzrinne, "An Extension to the Session Initiation Protocol (SIP) for Symmetric Response Jennings & Mahy Expires August 27, 2008 [Page 46] Internet-Draft Client Initiated Connections in SIP February 2008 Routing", RFC 3581, August 2003. [RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO 10646", STD 63, RFC 3629, November 2003. [RFC3840] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Indicating User Agent Capabilities in the Session Initiation Protocol (SIP)", RFC 3840, August 2004. [RFC3841] Rosenberg, J., Schulzrinne, H., and P. Kyzivat, "Caller Preferences for the Session Initiation Protocol (SIP)", RFC 3841, August 2004. [RFC3968] Camarillo, G., "The Internet Assigned Number Authority (IANA) Header Field Parameter Registry for the Session Initiation Protocol (SIP)", BCP 98, RFC 3968, December 2004. [RFC3969] Camarillo, G., "The Internet Assigned Number Authority (IANA) Uniform Resource Identifier (URI) Parameter Registry for the Session Initiation Protocol (SIP)", BCP 99, RFC 3969, December 2004. [RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986, January 2005. [RFC4122] Leach, P., Mealling, M., and R. Salz, "A Universally Unique IDentifier (UUID) URN Namespace", RFC 4122, July 2005. [RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, January 2008. 18.2. Informational References [I-D.ietf-sip-gruu] Rosenberg, J., "Obtaining and Using Globally Routable User Agent (UA) URIs (GRUU) in the Session Initiation Protocol (SIP)", draft-ietf-sip-gruu-15 (work in progress), October 2007. [I-D.ietf-sipping-config-framework] Channabasappa, S., "A Framework for Session Initiation Protocol User Agent Profile Delivery", draft-ietf-sipping-config-framework-15 (work in progress), February 2008. Jennings & Mahy Expires August 27, 2008 [Page 47] Internet-Draft Client Initiated Connections in SIP February 2008 [I-D.ietf-sipping-nat-scenarios] Boulton, C., "Best Current Practices for NAT Traversal for SIP", draft-ietf-sipping-nat-scenarios-07 (work in progress), July 2007. [RFC2104] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed- Hashing for Message Authentication", RFC 2104, February 1997. [RFC2782] Gulbrandsen, A., Vixie, P., and L. Esibov, "A DNS RR for specifying the location of services (DNS SRV)", RFC 2782, February 2000. [RFC3320] Price, R., Bormann, C., Christoffersson, J., Hannu, H., Liu, Z., and J. Rosenberg, "Signaling Compression (SigComp)", RFC 3320, January 2003. [RFC4346] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.1", RFC 4346, April 2006. [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, October 2006. Appendix A. Default Flow Registration Backoff Times The base-time used for the flow re-registration backoff times described in Section 4.5 are configurable. If the base-time-all-fail value is set to the default of 30 seconds and the base-time-not- failed value is set to the default of 90 seconds, the following table shows the resulting delay values. +-------------------+--------------------+--------------------+ | # of reg failures | all flows unusable | >1 non-failed flow | +-------------------+--------------------+--------------------+ | 0 | 0 secs | 0 secs | | 1 | 30-60 secs | 90-180 secs | | 2 | 1-2 mins | 3-6 mins | | 3 | 2-4 mins | 6-12 mins | | 4 | 4-8 mins | 12-24 mins | | 5 | 8-16 mins | 15-30 mins | | 6 or more | 15-30 mins | 15-30 mins | +-------------------+--------------------+--------------------+ Jennings & Mahy Expires August 27, 2008 [Page 48] Internet-Draft Client Initiated Connections in SIP February 2008 Authors' Addresses Cullen Jennings (editor) Cisco Systems 170 West Tasman Drive Mailstop SJC-21/2 San Jose, CA 95134 USA Phone: +1 408 902-3341 Email: fluffy@cisco.com Rohan Mahy (editor) Plantronics 345 Encincal St Santa Cruz, CA 95060 USA Email: rohan@ekabal.com Jennings & Mahy Expires August 27, 2008 [Page 49] Internet-Draft Client Initiated Connections in SIP February 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Jennings & Mahy Expires August 27, 2008 [Page 50]