Internet DRAFT - draft-ietf-mpls-tp-psc-itu
draft-ietf-mpls-tp-psc-itu
MPLS Working Group J. Ryoo, Ed.
Internet-Draft ETRI
Updates: 6378 (if approved) E. Gray, Ed.
Intended status: Standards Track Ericsson
Expires: September 29, 2014 H. van Helvoort
Huawei Technologies
A. D'Alessandro
Telecom Italia
T. Cheung
ETRI
E. Osborne
March 28, 2014
MPLS Transport Profile (MPLS-TP) Linear Protection to Match the
Operational Expectations of SDH, OTN and Ethernet Transport Network
Operators
draft-ietf-mpls-tp-psc-itu-04.txt
Abstract
This document describes alternate mechanisms to perform some of the
functions of MPLS Transport Profile (MPLS-TP) linear protection
defined in RFC 6378, and also defines additional mechanisms. The
purpose of these alternate and additional mechanisms is to provide
operator control and experience that more closely models the behavior
of linear protection seen in other transport networks.
This document also introduces capabilities and modes for linear
protection. A capability is an individual behavior, and a mode is a
particular combination of capabilities. Two modes are defined in
this document: Protection State Coordination (PSC) mode and Automatic
Protection Switching (APS) mode.
This document describes the behavior of the PSC protocol including
priority logic and state machine when all the capabilities associated
with the APS mode are enabled.
This document updates RFC 6378 in that the capability advertisement
method defined here is an addition to that document.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Ryoo, et al. Expires September 29, 2014 [Page 1]
Internet-Draft MPLS-TP LP for ITU-T March 2014
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 29, 2014.
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Conventions Used in This Document . . . . . . . . . . . . . . 5
3. Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Capability 1: Priority Modification . . . . . . . . . . . . . 6
4.1. Motivation for swapping priorities of FS and SF-P . . . . 6
4.2. Motivation for raising the priority of SFc . . . . . . . 7
4.3. Motivation for introducing Freeze command . . . . . . . . 7
4.4. Procedures in support of priority modification . . . . . 7
5. Capability 2: Non-revertive Behavior Modification . . . . . . 8
6. Capability 3: Support of MS-W Command . . . . . . . . . . . . 8
6.1. Motivation for adding MS-W . . . . . . . . . . . . . . . 8
6.2. Terminology to support MS-W . . . . . . . . . . . . . . . 9
6.3. Behavior of MS-P and MS-W . . . . . . . . . . . . . . . . 9
6.4. Equal priority resolution for MS . . . . . . . . . . . . 10
7. Capability 4: Support of Protection against SD . . . . . . . 10
7.1. Motivation for supporting protection against SD . . . . . 10
7.2. Terminology to support SD . . . . . . . . . . . . . . . . 10
7.3. Behavior of protection against SD . . . . . . . . . . . . 11
7.4. Equal priority resolution . . . . . . . . . . . . . . . . 12
Ryoo, et al. Expires September 29, 2014 [Page 2]
Internet-Draft MPLS-TP LP for ITU-T March 2014
8. Capability 5: Support of EXER Command . . . . . . . . . . . . 13
9. Capabilities and Modes . . . . . . . . . . . . . . . . . . . 14
9.1. Capabilities . . . . . . . . . . . . . . . . . . . . . . 14
9.1.1. Sending and receiving the Capabilities TLV . . . . . 15
9.2. Modes . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9.2.1. PSC mode . . . . . . . . . . . . . . . . . . . . . . 16
9.2.2. APS mode . . . . . . . . . . . . . . . . . . . . . . 16
10. PSC Protocol in APS Mode . . . . . . . . . . . . . . . . . . 16
10.1. Request field in PSC protocol message . . . . . . . . . 16
10.2. Priorities of local inputs and remote requests . . . . . 17
10.2.1. Equal priority requests . . . . . . . . . . . . . . 18
10.3. Acceptance and retention of local inputs . . . . . . . . 19
11. State Transition Tables in APS Mode . . . . . . . . . . . . . 20
11.1. State transition by local inputs . . . . . . . . . . . . 22
11.2. State transition by remote messages . . . . . . . . . . 24
11.3. State transition for 1+1 unidirectional
protection . . . . . . . . . . . . . . . . . . . . . . . 26
12. Provisioning Mismatch and Protocol Failure in APS Mode . . . 27
13. Security Considerations . . . . . . . . . . . . . . . . . . . 28
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 28
14.1. MPLS PSC Request Registry . . . . . . . . . . . . . . . 28
14.2. MPLS PSC TLV Registry . . . . . . . . . . . . . . . . . 28
14.3. MPLS PSC Capability Flag Registry . . . . . . . . . . . 28
15. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 29
16. References . . . . . . . . . . . . . . . . . . . . . . . . . 29
16.1. Normative References . . . . . . . . . . . . . . . . . . 29
16.2. Informative References . . . . . . . . . . . . . . . . . 29
Appendix A. An Example of Out-of-service Scenarios . . . . . . . 30
Appendix B. An Example of Sequence Diagram Showing
the Problem with the Priority Level of SFc . . . . . 31
Appendix C. Freeze Command . . . . . . . . . . . . . . . . . . . 33
Appendix D. Operation Examples of the APS Mode . . . . . . . . . 33
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 37
1. Introduction
Linear protection mechanisms for the MPLS Transport Profile (MPLS-TP)
are described in RFC 6378 [RFC6378] to meet the requirements
described in RFC 5654 [RFC5654].
This document describes alternate mechanisms to perform some of the
functions of linear protection, and also defines additional
mechanisms. The purpose of these alternate and additional mechanisms
is to provide operator control and experience that more closely
models the behavior of linear protection seen in other transport
networks, such as Synchronous Digital Hierarchy (SDH), Optical
Transport Network (OTN) and Ethernet transport networks. Linear
protection for SDH, OTN, and Ethernet transport networks are defined
Ryoo, et al. Expires September 29, 2014 [Page 3]
Internet-Draft MPLS-TP LP for ITU-T March 2014
in ITU-T Recommendations G.841 [G841], G.873.1 [G873.1] and G.8031
[G8031], respectively.
The reader of this document is assumed to be familiar with [RFC6378].
The alternative mechanisms described in this document are for the
following capabilities:
1. Priority modification,
2. non-revertive behavior modification,
and the following capabilities have been added to define additional
mechanisms:
3. support of Manual Switch to Working path (MS-W) command,
4. support of protection against Signal Degrade (SD), and
5. support of Exercise (EXER) command.
The priority modification includes raising the priority of Signal
Fail on Protection path (SF-P) relative to Forced Switch (FS), and
raising the priority level of Clear Signal Fail (SFc) above SF-P.
Non-revertive behavior is modified to align with the behavior defined
in RFC 4427 [RFC4427] as well as to follow the behavior of linear
protection seen in other transport networks.
Support of MS-W command to revert traffic to the working path in non-
revertive operation is covered in this document.
Support of protection switching protocol against SD is covered in
this document. The specifics for the method of identifying SD is out
of the scope for this document and is treated similarly to Signal
Fail (SF) in [RFC6378].
Support of EXER command to test if the Protection State Coordination
(PSC) communication is operating correctly is also covered in this
document. EXER command tests and validates the linear protection
mechanism and PSC protocol including the aliveness of the priority
logic, the PSC state machine and the PSC message generation and
reception, and the integrity of the protection path, without
triggering the actual traffic switching.
This document introduces capabilities and modes. A capability is an
individual behavior. The capabilities of a node are advertised using
the method given in this document. A mode is a particular
Ryoo, et al. Expires September 29, 2014 [Page 4]
Internet-Draft MPLS-TP LP for ITU-T March 2014
combination of capabilities. Two modes are defined in this document:
PSC mode and Automatic Protection Switching (APS) mode.
Other modes may be defined as new combinations of the capabilities
defined in this document or through the definition of additional
capabilities. In either case, the specification defining a new mode
will be responsible for documenting the behavior, the priority logic,
and the state machine of the PSC protocol when the set of
capabilities in the new mode are enabled.
This document describes the behavior, the priority logic, and the
state machine of the PSC protocol when all the capabilities
associated with the APS mode are enabled. The PSC protocol behavior
for the PSC mode is as defined in [RFC6378].
This document updates [RFC6378] by adding a capability advertisement
mechanism. It is recommended that existing implementations of the
PSC protocol be updated to support this capability. Backward
compatibility with existing implementations that do not support this
mechanism is described in Section 9.2.1.
Implementations are expected to be configured to support a specific
set of capabilities (a mode) and to reject messages that indicate the
use of a different set of capabilities (a different mode). Thus, the
capabilities advertisement is not a negotiation, but a verification
that peers are using the same mode.
2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Acronyms
Ryoo, et al. Expires September 29, 2014 [Page 5]
Internet-Draft MPLS-TP LP for ITU-T March 2014
This document uses the following acronyms:
APS Automatic Protection Switching
DNR Do-not-Revert
EXER Exercise
FS Forced Switch
LO Lockout of protection
MS Manual Switch
MS-P Manual Switch to Protection path
MS-W Manual Switch to Working path
MPLS-TP MPLS Transport Profile
NR No Request
OC Operator Clear
OTN Optical Transport Network
PSC Protection State Coordination
RR Reverse Request
SD Signal Degrade
SDH Synchronous Digital Hierarchy
SD-P Signal Degrade on Protection path
SD-W Signal Degrade on Working path
SF Signal Fail
SFc Clear Signal Fail
SFDc Clear Signal Fail or Degrade
SF-P Signal Fail on Protection path
SF-W Signal Fail on Working path
WTR Wait-to-Restore
4. Capability 1: Priority Modification
[RFC6378] defines the priority of FS to be higher than that of SF-P.
That document also defines the priority of Clear SF (SFc) to be low.
This document defines the priority modification capability whereby
the relative priorities of FS and SF-P are swapped and the priority
of Clear SF (SFc) is raised. In addition, this capability introduces
the Freeze command as described in Appendix C. The rationale for
these changes is detailed in the following sub-sections from both the
technical and network operational aspects.
4.1. Motivation for swapping priorities of FS and SF-P
Defining the priority of FS higher than that of SF-P can result in a
situation where the protected traffic is taken out-of-service. When
the protection path fails PSC communication may stop as a result. In
this case, if any input that is supposed to be signaled to the other
end has a higher priority than SF-P then this can result in
unpredictable protection switching state. An example scenario that
may result in an out-of-service situation is presented in Appendix A
of this document.
Ryoo, et al. Expires September 29, 2014 [Page 6]
Internet-Draft MPLS-TP LP for ITU-T March 2014
According to Section 2.4 of [RFC5654] it MUST be possible to operate
an MPLS-TP network without using a control plane. This means that
the PSC communication channel is very important for the transfer of
external switching commands (e.g., FS), and these commands should not
rely on the presence of a control plane. In consequence, the failure
of the PSC communication channel has higher priority than FS.
In other transport networks (such as SDH, OTN, and Ethernet transport
networks) the priority of SF-P has been higher than that of FS. It
is therefore important to offer network operators the option of
having the same behavior in their MPLS-TP networks so that they can
have the same operational protection switching behavior to which they
have become accustomed. Typically, FS command is issued before
network maintenance jobs, (e.g., replacing optical cables or other
network components). When an operator pulls out a cable on the
protection path, by mistake, the traffic should continue to be
protected and the operator expects this behavior based on his/her
experience on the traditional transport network operations.
4.2. Motivation for raising the priority of SFc
The priority level of SFc defined in [RFC6378] can cause traffic
disruption when a node that has experienced local signal fails on
both the working and the protection paths is recovering from these
failures.
An example of sequence diagram highlighting the problem with the
priority level of SFc as defined in [RFC6378] is presented in
Appendix B.
4.3. Motivation for introducing Freeze command
With the priority swapping between FS and SF-P, the traffic is always
moved back to the working path when SF-P occurs in Protecting
Administrative state. In case network operators need an option to
control their networks so that the traffic can remain on the
protection path even when the PSC communication channel is broken,
the Freeze command can be used. Freeze is defined to be a "local"
command that is not signaled to the remote node. The use of the
Freeze command is described in Appendix C.
4.4. Procedures in support of priority modification
When the modified priority order specified in this document is in
use, the list of local requests in order of priority SHALL be as
follows:
(from highest to lowest)
Ryoo, et al. Expires September 29, 2014 [Page 7]
Internet-Draft MPLS-TP LP for ITU-T March 2014
o Clear Signal Fail
o Signal Fail on Protection path
o Forced Switch
o Signal Fail on Working path
This requires modification to the PSC Control Logic (including the
state machine) relative to that described in [RFC6378]. Sections 10
and 11 present the PSC Control Logic when all capabilities of APS
mode are enabled.
5. Capability 2: Non-revertive Behavior Modification
Non-revertive operation of protection switching is defined in
[RFC4427]. In this operation, the traffic does not return to the
working path when switch-over requests are terminated.
However, the PSC protocol defined in [RFC6378] supports this
operation only when recovering from a defect condition: it does not
support the non-revertive function when an operator's switch-over
command, such as FS or Manual Switch (MS), is cleared. To be aligned
with the behavior in other transport networks and to be consistent
with [RFC4427], a node should go into the Do-not-Revert (DNR) state
not only when a failure condition on the working path is cleared, but
also when an operator command that requested switch-over is cleared.
This requires modification to the PSC Control Logic (including the
state machine) relative to that described in [RFC6378]. Sections 10
and 11 present the PSC Control Logic when all capabilities of APS
mode are enabled.
6. Capability 3: Support of MS-W Command
6.1. Motivation for adding MS-W
Changing the non-revertive operation as described in Section 5
introduces necessity of a new operator command to revert traffic to
the working path in the DNR state. When the traffic is on the
protection path in the DNR state, a Manual Switch to Working (MS-W)
command is issued to switch the normal traffic back to the working
path. According to Section 4.3.3.6 (Do-not-Revert State) in
[RFC6378], "to revert back to the Normal state, the administrator
SHALL issue a Lockout of protection (LO) command followed by a Clear
command." However, using LO command introduces the potential risk of
an unprotected situation while the LO is in effect.
Ryoo, et al. Expires September 29, 2014 [Page 8]
Internet-Draft MPLS-TP LP for ITU-T March 2014
Manual Switch-over for recovery LSP/span command is defined in
[RFC4427]. Requirement 83 in [RFC5654] states that the external
commands defined in [RFC4427] MUST be supported. Since there is no
support for this external command in [RFC6378], this functionality
should be added to PSC. This support is provided by introducing the
MS-W command. The MS-W command, as described here, corresponds to
the "Manual Switch-over for recovery LSP/span" command.
6.2. Terminology to support MS-W
[RFC6378] uses the term "Manual Switch" and its acronym "MS". This
document uses the term "Manual Switch to Protection path" and "MS-P"
to have the same meaning, while avoiding confusion with "Manual
Switch to Working path" and its acronym "MS-W".
Similarly, we modify the name of "Protecting Administrative" state
(as defined in [RFC6378]) to be "Switching Administrative" state to
include the case where traffic is switched to the working path as a
result of the external MS-W command.
6.3. Behavior of MS-P and MS-W
MS-P and MS-W SHALL have the same priority. We consider different
instances of determining the priority of the commands when they are
received either in succession or simultaneously.
o When two commands are received in succession, the command that is
received after the initial command SHALL be cancelled.
o If two nodes simultaneously receive commands that indicate
opposite operations (i.e., one node receives MS-P and the other
node receives MS-W) and transmit the indications to the remote
node, the MS-W SHALL be considered to have a higher priority, and
the MS-P SHALL be cancelled and discarded.
Two commands, MS-P and MS-W are transmitted using the same Request
field value, but SHALL indicate in the Fault Path (FPath) value the
path that the traffic is being diverted from. When traffic is
switched to the protection path, the FPath field value SHALL be set
to 1, indicating that traffic is being diverted from the working
path. When traffic is switched to the working path, the FPath field
value SHALL be set to 0, indicating that traffic is being diverted
from the protection path. The Data Path (Path) field SHALL indicate
where user data traffic is being transported (i.e., if the working
path is selected, then Path is set to 0; if the protection path is
selected, then Path is set to 1).
Ryoo, et al. Expires September 29, 2014 [Page 9]
Internet-Draft MPLS-TP LP for ITU-T March 2014
When an MS command is in effect at a node, any subsequent MS or EXER
command and any other lower priority requests SHALL be ignored.
6.4. Equal priority resolution for MS
[RFC6378] defines only one rule for equal priority condition in
Section 4.3.2 as "The remote message from the remote LER is assigned
a priority just below the similar local input." In order to support
the manual switch behavior described in Section 6.3, additional rules
for equal priority resolution are required. Since the support of
protection against signal degrade also requires a similar equal
priority resolution, the rules are described in Section 7.4.
Support of this function requires changes to the PSC Control Logic
(including the state machine) relative to that shown in [RFC6378].
Sections 10 and 11 present the PSC Control Logic when all
capabilities of APS mode are enabled.
7. Capability 4: Support of Protection against SD
7.1. Motivation for supporting protection against SD
In the MPLS-TP Survivability Framework [RFC6372], both SF and SD
fault conditions can be used to trigger protection switching.
[RFC6378], which defines the protection switching protocol for MPLS-
TP, does not specify how the SF and SD are detected, and specifies
the protection switching protocol associated with SF only.
The PSC protocol associated with SD is covered in this document, but
the specifics for the method of identifying SD is out of scope for
the protection protocol in the same way that SF detection and MS or
FS command initiation are out of scope.
7.2. Terminology to support SD
In this document the term Clear Signal Fail or Degrade (SFDc) is used
to indicate the clearance of either a degraded condition or a failure
condition.
The second paragraph of Section 4.3.3.2 Unavailable state in
[RFC6378] shows the intention of including Signal Degrade on
Protection path (SD-P) in the Unavailable state. Even though the
protection path can be partially available under the condition of
SD-P, this document follows the same state grouping as [RFC6378] for
SD-P.
Ryoo, et al. Expires September 29, 2014 [Page 10]
Internet-Draft MPLS-TP LP for ITU-T March 2014
The bullet item on the Protecting Failure state in Section 3.6 of
[RFC6378] includes the degraded condition in the Protecting Failure
state. This document follows the same state grouping as [RFC6378]
for Signal Degrade on Working path (SD-W).
7.3. Behavior of protection against SD
To better align the behavior of MPLS-TP networks with that of other
transport networks (such as SDH, OTN, and Ethernet transport
networks) we define the followings:
o The priorities of SD-P and SD-W SHALL be equal.
o Once a switch has been completed due to SD on one path, it will
not be overridden by SD on the other path (first come, first
served behavior), to avoid protection switching that cannot
improve signal quality.
The SD message indicates that the transmitting node has identified
degradation of the signal or integrity of the packet received on
either the working path or the protection path. The FPath field
SHALL identify the path that is reporting the degraded condition
(i.e., if the protection path, then FPath is set to 0; if the working
path, then FPath is set to 1), and the Path field SHALL indicate
where the data traffic is being transported (i.e., if the working
path is selected, then Path is set to 0; if the protection path is
selected, then Path is set to 1).
When the SD condition is cleared and the protected domain is
recovering from the situation, the Wait-to-Restore (WTR) timer SHALL
be used if the protected domain is configured for revertive behavior.
The WTR timer SHALL be started at the node that recovers from a local
degraded condition on the working path.
Protection switching against SD is always provided by a selector
bridge duplicating user data traffic and feeding it to both the
working path and the protection path under SD condition. When a
local or remote SD occurs on either the working path or the
protection path, the node SHALL duplicate user data traffic and SHALL
feed to both the working path and the protection path. The packet
duplication SHALL continue as long as any SD condition exists in the
protected domain. When the SD condition is cleared, in revertive
operation, the packet duplication SHALL continue in the WTR state and
SHALL stop when the node leaves the WTR state; while in non-revertive
operation, the packet duplication SHALL stop immediately.
Ryoo, et al. Expires September 29, 2014 [Page 11]
Internet-Draft MPLS-TP LP for ITU-T March 2014
The selector bridge with the packet duplication under SD condition,
which is a non-permanent bridge, is considered to be a 1:1 protection
architecture.
Protection switching against SD does not introduce any modification
to the operation of the selector at the sink node described in
[RFC6378]. The selector chooses either the working or protection
path from which to receive the normal traffic in both 1:1 and 1+1
architectures. The position of the selector, i.e., which path to
receive the traffic, is determined by the PSC protocol in
bidirectional switching or by the local input in unidirectional
switching.
7.4. Equal priority resolution
In order to support the MS behavior described in Section 6.3 and the
protection against SD described in Section 7.3, it is necessary to
expand rules for treating equal priority inputs.
For equal priority local inputs, such as MS and SD, apply a simple
first-come, first-served rule. Once a local input is determined as
the highest priority local input, then a subsequent equal priority
local input requesting a different action, i.e., the action results
in the same PSC Request field but different FPath value, will not be
presented to the PSC Control Logic as the highest local request.
Furthermore, in the case of MS command, the subsequent local MS
command requesting a different action will be cancelled.
If a node is in a remote state due to a remote SD (or MS) message, a
subsequent local input having the same priority but requesting a
different action to the PSC Control Logic, will be considered as
having lower priority than the remote message, and will be ignored.
For examples, if a node is in remote Switching Administrative state
due to a remote MS-P, then any subsequent local MS-W SHALL be ignored
and automatically cancelled. If a node is in remote Unavailable
state due to a remote SD-P, then any subsequent local SD-W input will
be ignored. However, the local SD-W SHALL continue to appear in the
Local Request Logic as long as the SD condition exists, but SHALL NOT
be the top priority global request, which determines the state
transition at the PSC Control Logic.
Cases where two end-points of the protected domain simultaneously
receive local triggers of the same priority that request different
actions (for example, one node receives SD-P and the other receives
SD-W) may occur. Subsequently, each node will receive a remote
message with the opposing action indication. To address these cases,
we define the following priority resolution rules:
Ryoo, et al. Expires September 29, 2014 [Page 12]
Internet-Draft MPLS-TP LP for ITU-T March 2014
o When MS-W and MS-P occur simultaneously at both nodes, MS-W SHALL
be considered as having higher priority than MS-P at both nodes.
o When SD-W and SD-P occur simultaneously at both nodes, the SD on
the standby path (the path from which the selector does not select
the user data traffic) is considered as having higher priority
than the SD on the active path (the path from which the selector
selects the user data traffic) regardless of its origin (local or
remote message). Therefore, no unnecessary protection switching
is performed and the user data traffic continues to be selected
from the active path.
In the preceding paragraphs, the "simultaneously" refers to the case
a sent SD (or MS) request has not been confirmed by the remote end in
bidirectional protection switching. When a local node that has
transmitted a SD message receives a SD (or MS) message that indicates
a different value of Path field from the value of Path field in the
transmitted SD (or MS) message, both the local and remote SD requests
are considered to occur simultaneously.
The addition of support for protection against SD requires
modification to the PSC Control Logic (including the state machine)
relative to that described in [RFC6378]. Sections 10 and 11 present
the PSC Control Logic when all capabilities of APS mode are enabled.
8. Capability 5: Support of EXER Command
The EXER command is used to verify the correct operation of the PSC
communication, such as the aliveness of the Local Request Logic, the
integrity of the PSC Control Logic, the PSC message generation and
reception mechanism, and the integrity of the protection path. EXER
does not trigger any actual traffic switching.
The command is only relevant for bidirectional protection switching,
since it is dependent upon receiving a response from the remote node.
The EXER command is assigned lower priority than any switching
message. It may be used regardless of the traffic usage of the
working path.
When a node receives a remote EXER message, it SHOULD respond with a
Reverse Request (RR) message with the FPath and Path fields set
according to the current condition of the node. The RR message SHALL
be generated only in response to a remote EXER message.
This command is documented in R84 of [RFC5654].
If EXER commands are input at both ends, then a race condition may
arise. This is resolved as follows:
Ryoo, et al. Expires September 29, 2014 [Page 13]
Internet-Draft MPLS-TP LP for ITU-T March 2014
o If a node has issued EXER and receives EXER before receiving RR,
it MUST treat the received EXER as it would an RR, and SHOULD NOT
respond with RR.
The following PSC Requests are added to the PSC Request field to
support the Exercise command (see also Section 14.1):
(3) Exercise - indicates that the transmitting end point is
exercising the protection channel and mechanism. FPath and Path
are set to the same value of the No Request (NR), RR or DNR
message whose transmission is stopped by EXER.
(2) Reverse Request - indicates that the transmitting end point is
responding to an EXER command from the remote node. FPath and
Path are set to the same value of the NR or DNR message whose
transmission is stopped by RR.
The relative priorities of EXER and RR are defined in Section 10.2.
9. Capabilities and Modes
9.1. Capabilities
A Capability is an individual behavior whose use is signaled in a
Capabilities TLV, which is placed in Optional TLVs field inside the
PSC message shown in Figure 2 of [RFC6378]. The format of the
Capabilities TLV is:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = Capabilities | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value = Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Format of Capabilities TLV
The value of the Type field is TBD pending IANA allocation.
The value of the Length field is the length of the Flags field in
octets. The length of the Flags field MUST be a multiple of 4 octets
and MUST be the minimum required to signal all the required
capabilities.
Section 4 to Section 8 discuss five capabilities that are signaled
using the five most significant bits; if a node wishes to signal
these five capabilities, it MUST send a Flags field of 4 octets. A
Ryoo, et al. Expires September 29, 2014 [Page 14]
Internet-Draft MPLS-TP LP for ITU-T March 2014
node would send a Flags field greater than 4 octets only if it had
more than 32 Capabilities to indicate. All unused bits MUST be set
to zero.
If the bit assigned for an individual capability is set to 1, it
indicates the sending node's intent to use that capability in the
protected domain. If a bit is set to 0, the sending node does not
intend to use the indicated capability in the protected domain. Note
that it is not possible to distinguish between the intent not to use
a capability and a node's complete non-support (i.e., lack of
implementation) of a given capability.
This document defines five specific capabilities that are described
in Section 4 to Section 8. Each capability is assigned bit as
follows:
0x80000000: priority modification
0x40000000: non-revertive behavior modification
0x20000000: support of MS-W command
0x10000000: support of protection against SD
0x08000000: support of EXER command
If all the five capabilities should be used, a node SHALL set the
Flags field to 0xF8000000.
9.1.1. Sending and receiving the Capabilities TLV
A node MUST include its Capabilities TLV in every PSC message that it
transmits. The transmission and acceptance of the PSC message is
described in Section 4.1 of [RFC6378].
When a node receives a Capabilities TLV it MUST compare the Flags
value to its most recent Flags value transmitted by the node. If the
two are equal, the protected domain is said to be running in the mode
indicated by that set of capabilities (see Section 9.2). If the sent
and received Capabilities TLVs are not equal, this indicates a
capabilities TLV mismatch. When this happens, the node MUST alert
the operator and MUST NOT perform any protection switching until the
operator resolves the mismatch between the two end-points.
Ryoo, et al. Expires September 29, 2014 [Page 15]
Internet-Draft MPLS-TP LP for ITU-T March 2014
9.2. Modes
A mode is a given set of Capabilities. Modes are shorthand;
referring to a set of capabilities by their individual values or by
the name of their mode does not change the protocol behavior. This
document defines two modes - PSC and APS. Capability TLVs with other
combinations than the one specified by a mode are not supported in
this specification.
9.2.1. PSC mode
PSC mode is defined as the lack of support for any of the additional
capabilities defined in this document - that is, a Capabilities set
of 0x0. It is the behavior specified in [RFC6378].
There are two ways to declare PSC mode. A node can send no
Capabilities TLV at all since there are no TLV units defined in
[RFC6378], or it can send a Capabilities TLV with Flags value set to
0x0. In order to allow backward compatibility between two end-points
- one which supports sending the Capabilities TLV, and one which does
not, the node that has the ability to send and process the PSC mode
Capabilities TLV MUST be able to both send the PSC mode Capabilities
TLV and send no Capabilities TLV at all. An implementation MUST be
configurable between these two options.
9.2.2. APS mode
APS mode is defined as the use of all the five specific capabilities,
which are described in Section 4 to Section 8 in this document. APS
mode is indicated with the Flags value of 0xF8000000.
10. PSC Protocol in APS Mode
This section and the following section define the behavior of PSC
protocol when all of the aforementioned capabilities are enabled,
i.e., APS mode.
10.1. Request field in PSC protocol message
This document defines two new values for the "Request" field in the
PSC protocol message that is shown in Figure 2 of [RFC6378] as
follows:
(3) Exercise
(2) Reverse Request
See also Section 14.1 of this document.
Ryoo, et al. Expires September 29, 2014 [Page 16]
Internet-Draft MPLS-TP LP for ITU-T March 2014
10.2. Priorities of local inputs and remote requests
Based on the description in Sections 3 and 4.3.2 in [RFC6378], the
priorities of multiple outstanding local inputs are evaluated in the
Local Request Logic, where the highest priority local input (highest
local request) is determined. This highest local request is passed
to the PSC Control Logic, that will determine the higher priority
input (top priority global request) between the highest local request
and the last received remote message. When a remote message comes to
the PSC Control Logic, the top priority global request is determined
between this remote message and the highest local request which is
present. The top priority global request is used to determine the
state transition, which is described in Section 11. In this
document, in order to simplify the description on the PSC Control
Logic, we strictly decouple the priority evaluation from the state
transition table lookup.
The priorities for both local and remote requests are defined as
follows from highest to lowest:
o Operator Clear (Local only)
o Lockout of protection (Local and Remote)
o Clear Signal Fail or Degrade (Local only)
o Signal Fail on Protection path (Local and Remote)
o Forced Switch (Local and Remote)
o Signal Fail on Working path (Local and Remote)
o Signal Degrade on either Protection path or Working path (Local
and Remote)
o Manual Switch to either Protection path or Working path (Local and
Remote)
o WTR Timer Expiry (Local only)
o WTR (Remote only)
o Exercise (Local and Remote)
o Reverse Request (Remote only)
o Do-Not-Revert (Remote only)
Ryoo, et al. Expires September 29, 2014 [Page 17]
Internet-Draft MPLS-TP LP for ITU-T March 2014
o No Request (Remote and Local)
Note that the "Local only" requests are not tranmitted to the remote
node. Likewise, the "Remote only" requests do not exist in the Local
Request Logic as local inputs. For example, the priority of WTR only
applies to the received WTR message, which is generated from the
remote node. The remote node that is running the WTR timer in the
WTR state has no local request.
The remote SF and SD on either the working path or the protection
path and the remote MS to either the working path or the protection
path are indicated by the values of the Request and FPath fields in
the PSC message.
The remote request from the remote node is assigned a priority just
below the same local request except NR and equal priority requests,
such as SD and MS. Since a received NR message needs to be used in
the state transition table lookup when there is no outstanding local
request, the remote NR request SHALL have a higher priority than the
local NR. For the equal priority requests, see Section 10.2.1.
10.2.1. Equal priority requests
As stated in Section 10.2, the remote request from the remote node is
assigned a priority just below the same local request. However, for
equal priority requests, such as SD and MS, the priority SHALL be
evaluated as described in this section.
For equal priority local requests, first-come, first-served rule
SHALL be applied. Once a local request appears in the Local Request
Logic, a subsequent equal priority local request requesting a
different action, i.e., the action results in the same Request value
but a different FPath value, SHALL be considered to have a lower
priority. Furthermore, in the case of MS command, the subsequent
local MS command requesting a different action SHALL be rejected and
cleared.
When the priority is evaluated in the PSC Control Logic between the
highest local request and a remote request, the following equal
priority resolution rules SHALL be applied:
o If two requests request the same action, i.e., the same Request
and FPath values, then the local request SHALL be considered to
have a higher priority than the remote request.
o When the highest local request comes to the PSC Control Logic, if
the remote request that requests a different action exists, then
the highest local request SHALL be ignored and the remote request
Ryoo, et al. Expires September 29, 2014 [Page 18]
Internet-Draft MPLS-TP LP for ITU-T March 2014
SHALL remain to be the top priority global request. In the case
of MS command, the local MS command requesting a different action
SHALL be cancelled.
o When the remote request comes to the PSC Control Logic, if the
highest local request that requests a different action exists,
then the top priority global request SHALL be determined by the
following rules:
* For MS requests, the MS-W request SHALL be considered to have a
higher priority than the MS-P request. The node that has local
MS-W request SHALL maintain the local MS-W request as the top
priority global request. The other node that has local MS-P
request SHALL cancel the MS-P command and SHALL generate
"Operator Clear" internally as the top priority global request.
* For SD requests, the SD on the standby path (the path from
which the selector does not select the user data traffic) SHALL
be considered to have a higher priority than the SD on the
active path (the path from which the selector selects the user
data traffic) regardless of its origin (local or remote
message). The node that has the SD on the standby path SHALL
maintain the local SD on the standby path request as the top
priority global request. The other node that has local SD on
the active path SHALL use the remote SD on the standby path as
the top priority global request to lookup the state transition
table. The differentiation of the active and standby paths is
based upon which path had been selected for the user data
traffic "when each node detected its local SD".
10.3. Acceptance and retention of local inputs
A local input indicating a defect, such as SF-P, SF-W, SD-P and SD-W,
SHALL be accepted and retained persistently in the Local Request
Logic as long as the defect condition exists. If there is any higher
priority local input than the local defect input, the higher priority
local input is passed to the PSC Control Logic as the highest local
request, but the local defect input cannot be removed but remains in
the Local Request Logic. When the higher priority local input is
cleared, the local defect will become the highest local request if
the defect condition still exists.
Operator Clear (OC) command, SFDc and WTR Timer Expiry are not
persistent. Once they appear to the Local Request Logic and complete
all the operations in the protection switching control, they SHALL
disappear.
Ryoo, et al. Expires September 29, 2014 [Page 19]
Internet-Draft MPLS-TP LP for ITU-T March 2014
LO, FS, MS, and EXER commands SHALL be rejected if there is any
higher priority local input in the Local Request Logic. If a new
higher-priority local request (including an operator command) is
accepted, any previous lower-priority local operator command SHALL be
cancelled. When any higher-priority remote request is received, a
lower-priority local operator command SHALL be cancelled. The
cancelled operator command is cleared. If the operators wish to
renew the cancelled command then they should reissue the command.
11. State Transition Tables in APS Mode
When there is a change in the highest local request or in remote PSC
messages, the top priority global request SHALL be evaluated and the
state transition tables SHALL be looked up in the PSC Control Logic.
The following rules are applied to the operation related to the state
transition table lookup.
o If the top priority global request, which determines the state
transition, is the highest local request, the local state
transition table in Section 11.1 SHALL be used to decide the next
state of the node. Otherwise, the remote state transition table
in Section 11.2 SHALL be used.
o If in remote state, the highest local defect condition (SF-P,
SF-W, SD-P or SD-W) SHALL always be reflected in the Request and
Fpath fields.
o For the node currently in the local state, if the top priority
global request is changed to OC or SFDc causing the next state to
be Normal, WTR or DNR, then all the local and remote requests
SHALL be re-evaluated as if the node is in the state specified in
the footnotes to the state transition tables, before deciding the
final state. If there are no active requests, the node enters the
state specified in the footnotes to the state transition tables.
This re-evaluation is an internal operation confined within the
local node, and the PSC messages are generated according to the
final state.
o The WTR timer is started only when the node which has recovered
from a local failure or degradation enters the WTR state. A node
which is entering into the WTR state due to a remote WTR message
does not start the WTR timer. The WTR timer SHALL be stopped when
any local or remote request triggers the state change out of the
WTR state.
The extended states, as they appear in the table, are as follows:
Ryoo, et al. Expires September 29, 2014 [Page 20]
Internet-Draft MPLS-TP LP for ITU-T March 2014
N Normal state
UA:LO:L Unavailable state due to local LO command
UA:P:L Unavailable state due to local SF-P
UA:DP:L Unavailable state due to local SD-P
UA:LO:R Unavailable state due to remote LO message
UA:P:R Unavailable state due to remote SF-P message
UA:DP:R Unavailable state due to remote SD-P message
PF:W:L Protecting Failure state due to local SF-W
PF:DW:L Protecting Failure state due to local SD-W
PF:W:R Protecting Failure state due to remote SF-W message
PF:DW:R Protecting Failure state due to remote SD-W message
SA:F:L Switching Administrative state due to local FS command
SA:MW:L Switching Administrative state due to local MS-W command
SA:MP:L Switching Administrative state due to local MS-P command
SA:F:R Switching Administrative state due to remote FS message
SA:MW:R Switching Administrative state due to remote MS-W message
SA:MP:R Switching Administrative state due to remote MS-P message
WTR Wait-to-Restore state
DNR Do-not-Revert state
E::L Exercise state due to local EXER command
E::R Exercise state due to remote EXER message
Each state corresponds to the transmission of a particular set of
Request, FPath and Path fields. The table below lists the message
that is generally sent in each particular state. If the message to
be sent in a particular state deviates from the table below, it is
noted in the footnotes to the state transition tables.
Ryoo, et al. Expires September 29, 2014 [Page 21]
Internet-Draft MPLS-TP LP for ITU-T March 2014
State Request(FPath,Path)
------- ------------------------------------
N NR(0,0)
UA:LO:L LO(0,0)
UA:P:L SF(0,0)
UA:DP:L SD(0,0)
UA:LO:R highest local request(local FPath,0)
UA:P:R highest local request(local FPath,0)
UA:DP:R highest local request(local FPath,0)
PF:W:L SF(1,1)
PF:DW:L SD(1,1)
PF:W:R highest local request(local FPath,1)
PF:DW:R highest local request(local FPath,1)
SA:F:L FS(1,1)
SA:MW:L MS(0,0)
SA:MP:L MS(1,1)
SA:F:R highest local request(local FPath,1)
SA:MW:R NR(0,0)
SA:MP:R NR(0,1)
WTR WTR(0,1)
DNR DNR(0,1)
E::L EXER(0,x), where x is the existing Path value
when Exercise command is issued.
E::R RR(0,x), where x is the existing Path value
when RR message is generated.
Some operation examples of APS mode are shown in Appendix D.
In the state transition tables below, the letter 'i' stands for
"ignore", and is an indication to remain in the current state and
continue transmitting the current PSC message
11.1. State transition by local inputs
Ryoo, et al. Expires September 29, 2014 [Page 22]
Internet-Draft MPLS-TP LP for ITU-T March 2014
| OC | LO | SFDc | SF-P | FS | SF-W |
--------+-----+---------+------+--------+--------+--------+
N | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
UA:LO:L | (1) | i | i | i | i | i |
UA:P:L | i | UA:LO:L | (1) | i | i | i |
UA:DP:L | i | UA:LO:L | (1) | UA:P:L | SA:F:L | PF:W:L |
UA:LO:R | i | UA:LO:L | i | UA:P:L | i | PF:W:L |
UA:P:R | i | UA:LO:L | i | UA:P:L | i | PF:W:L |
UA:DP:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
PF:W:L | i | UA:LO:L | (2) | UA:P:L | SA:F:L | i |
PF:DW:L | i | UA:LO:L | (2) | UA:P:L | SA:F:L | PF:W:L |
PF:W:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
PF:DW:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
SA:F:L | (3) | UA:LO:L | i | UA:P:L | i | i |
SA:MW:L | (1) | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
SA:MP:L | (3) | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
SA:F:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
SA:MW:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
SA:MP:R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
WTR | (4) | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
DNR | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
E::L | (5) | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
E::R | i | UA:LO:L | i | UA:P:L | SA:F:L | PF:W:L |
| SD-P | SD-W | MS-W | MS-P | WTRExp | EXER
--------+---------+---------+---------+---------+--------+------
N | UA:DP:L | PF:DW:L | SA:MW:L | SA:MP:L | i | E::L
UA:LO:L | i | i | i | i | i | i
UA:P:L | i | i | i | i | i | i
UA:DP:L | i | i | i | i | i | i
UA:LO:R | UA:DP:L | PF:DW:L | i | i | i | i
UA:P:R | UA:DP:L | PF:DW:L | i | i | i | i
UA:DP:R | UA:DP:L | PF:DW:L | i | i | i | i
PF:W:L | i | i | i | i | i | i
PF:DW:L | i | i | i | i | i | i
PF:W:R | UA:DP:L | PF:DW:L | i | i | i | i
PF:DW:R | UA:DP:L | PF:DW:L | i | i | i | i
SA:F:L | i | i | i | i | i | i
SA:MW:L | UA:DP:L | PF:DW:L | i | i | i | i
SA:MP:L | UA:DP:L | PF:DW:L | i | i | i | i
SA:F:R | UA:DP:L | PF:DW:L | i | i | i | i
SA:MW:R | UA:DP:L | PF:DW:L | SA:MW:L | i | i | i
SA:MP:R | UA:DP:L | PF:DW:L | i | SA:MP:L | i | i
WTR | UA:DP:L | PF:DW:L | SA:MW:L | SA:MP:L | (6) | i
DNR | UA:DP:L | PF:DW:L | SA:MW:L | SA:MP:L | i | E::L
E::L | UA:DP:L | PF:DW:L | SA:MW:L | SA:MP:L | i | i
E::R | UA:DP:L | PF:DW:L | SA:MW:L | SA:MP:L | i | E::L
Ryoo, et al. Expires September 29, 2014 [Page 23]
Internet-Draft MPLS-TP LP for ITU-T March 2014
NOTES:
(1) Re-evaluate to determine final state as if the node is in the
Normal state. If there are no active requests, the node enters
the Normal State.
(2) In the case that both local input after SFDc and the last
received remote message are no requests, the node enters into
the WTR state when the domain is configured for revertive
behavior, or the node enters into the DNR state when the domain
is configured for non-revertive behavior. In all the other
cases, where one or more active requests exist, re-evaluate to
determine the final state as if the node is in the Normal state.
(3) Re-evaluate to determine final state as if the node is in the
Normal state when the domain is configured for revertive
behavior, or as if the node is in the DNR state when the domain
is configured for non-revertive behavior. If there are no
active requests, the node enters either the Normal state when
the domain is configured for revertive behavior or the DNR state
when the domain is configured for non-revertive behavior.
(4) Remain in the WTR state and send NR(0,1). Stop the WTR timer if
it is running. In APS mode, OC can cancel the WTR timer and
hasten the state transition to the Normal state as in other
transport networks.
(5) If Path value is 0, re-evaluate to determine final state as if
the node is in the Normal state. If Path value is 1, re-
evaluate to determine final state as if the node is in the DNR
state. If there are no active requests, the node enters the
Normal state when Path value is 0, or the DNR state when Path
value is 1.
(6) Remain in the WTR state and send NR(0,1).
11.2. State transition by remote messages
Ryoo, et al. Expires September 29, 2014 [Page 24]
Internet-Draft MPLS-TP LP for ITU-T March 2014
| LO | SF-P | FS | SF-W | SD-P | SD-W |
--------+---------+--------+--------+--------+---------+---------+
N | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
UA:LO:L | i | i | i | i | i | i |
UA:P:L | UA:LO:R | i | i | i | i | i |
UA:DP:L | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | i | (7) |
UA:LO:R | i | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
UA:P:R | UA:LO:R | i | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
UA:DP:R | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | i | PF:DW:R |
PF:W:L | UA:LO:R | UA:P:R | SA:F:R | i | i | i |
PF:DW:L | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | (8) | i |
PF:W:R | UA:LO:R | UA:P:R | SA:F:R | i | UA:DP:R | PF:DW:R |
PF:DW:R | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | i |
SA:F:L | UA:LO:R | UA:P:R | i | i | i | i |
SA:MW:L | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
SA:MP:L | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
SA:F:R | UA:LO:R | UA:P:R | i | PF:W:R | UA:DP:R | PF:DW:R |
SA:MW:R | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
SA:MP:R | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
WTR | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
DNR | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
E::L | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
E::R | UA:LO:R | UA:P:R | SA:F:R | PF:W:R | UA:DP:R | PF:DW:R |
| MS-W | MS-P | WTR | EXER | RR | DNR | NR
--------+---------+---------+-----+------+----+------+----
N | SA:MW:R | SA:MP:R | i | E::R | i | i | i
UA:LO:L | i | i | i | i | i | i | i
UA:P:L | i | i | i | i | i | i | i
UA:DP:L | i | i | i | i | i | i | i
UA:LO:R | SA:MW:R | SA:MP:R | i | E::R | i | i | N
UA:P:R | SA:MW:R | SA:MP:R | i | E::R | i | i | N
UA:DP:R | SA:MW:R | SA:MP:R | i | E::R | i | i | N
PF:W:L | i | i | i | i | i | i | i
PF:DW:L | i | i | i | i | i | i | i
PF:W:R | SA:MW:R | SA:MP:R | (9) | E::R | i | (10) | (11)
PF:DW:R | SA:MW:R | SA:MP:R | (9) | E::R | i | (10) | (11)
SA:F:L | i | i | i | i | i | i | i
SA:MW:L | i | i | i | i | i | i | i
SA:MP:L | i | i | i | i | i | i | i
SA:F:R | SA:MW:R | SA:MP:R | i | E::R | i | DNR | N
SA:MW:R | i | SA:MP:R | i | E::R | i | i | N
SA:MP:R | SA:MW:R | i | i | E::R | i | DNR | N
WTR | SA:MW:R | SA:MP:R | i | i | i | i | (12)
DNR | SA:MW:R | SA:MP:R | (13)| E::R | i | i | i
E::L | SA:MW:R | SA:MP:R | i | i | i | i | i
E::R | SA:MW:R | SA:MP:R | i | i | i | DNR | N
Ryoo, et al. Expires September 29, 2014 [Page 25]
Internet-Draft MPLS-TP LP for ITU-T March 2014
NOTES:
(7) If the received SD-W message has Path=0, ignore the message. If
the received SD-W message has Path=1, go to the PF:DW:R state
and transmit SD(0,1)
(8) If the received SD-P message has Path=1, ignore the message. If
the received SD-P message has Path=0, go to the UA:DP:R state
and transmit SD(1,0).
(9) Transition to the WTR state and continue to send the current
message.
(10) Transition to the DNR state and continue to send the current
message.
(11) If the received NR message has Path=1, transition to the WTR
state if domain configured for revertive behavior, else
transition to the DNR state. If the received NR message has
Path=0, transition to the Normal state.
(12) If the receiving node's WTR timer is running, maintain current
state and message. If the WTR timer is not running, transition
to the Normal state.
(13) Transit to the WTR state and send NR(0,1) message. The WTR
timer is not initiated.
11.3. State transition for 1+1 unidirectional protection
The state transition tables given in Sections 11.1 and 11.2 are for
bidirectional protection switching, where remote PSC protocol
messages are used to determine the protection switching actions. 1+1
unidirectional protection switching does not require the remote
information in PSC protocol message and acts upon local inputs only.
The state transition by local inputs in Section 11.1 SHALL be reused
for 1+1 unidirectional protection under the following conditions:
o The value of Request field in the received remote message is
ignored and always assumed to be no request.
o Replace footnote (4) with "Stop the WTR timer and transit to the
Normal state."
o Replace footnote (6) with "Transit to the Normal state."
o Exercise command is not relevant.
Ryoo, et al. Expires September 29, 2014 [Page 26]
Internet-Draft MPLS-TP LP for ITU-T March 2014
12. Provisioning Mismatch and Protocol Failure in APS Mode
The remote PSC message that is received from the remote node is
subject to the detection of provisioning mismatch and protocol
failure conditions. In APS mode, provisioning mismatches are handled
as follows:
o If the PSC message is received from the working path due to
working/protection path configuration mismatch, the node MUST
alert the operator and MUST NOT perform any protection switching
until the operator resolves this path configuration mismatch.
o In the case that the mismatch happens in two-bit "Protection Type
(PT)" field, which indicates permanent/selector bridge type and
uni/bidirectional switching type,
* If the value of the PT field of one side is 2 (i.e., selector
bridge) and the value of PT field of the other side is 1 or 3
(i.e., permanent bridge), then this event MUST be notified to
the operator and each node MUST NOT perform any protection
switching until the operator resolves this bridge type
mismatch.
* If the bridge type matches but the switching type mismatches,
i.e., one side has PT=1 (unidirectional switching) while the
other side has PT=2 or 3 (bidirectional switching), then the
node provisioned for bidirectional switching SHOULD fall back
to unidirectional switching to allow interworking. The node
SHOULD notify the operator of this event.
o If the "Revertive (R)" bit mismatches, two sides will interwork
and traffic is protected according to the state transition
definition given in Section 11. The node SHOULD notify the
operator of this event.
o If the Capabilities TLV mismatches, the node MUST alert the
operator and MUST NOT perform any protection switching until the
operator resolves the mismatch in the Capabilities TLV.
The followings are the protocol failure situations and the actions to
be taken:
o No match in sent "Data Path (Path)" and received "Data Path
(Path)" for more than 50 ms: The node MAY continue to perform
protection switching and SHOULD notify the operator of this event.
o No PSC message is received on the protection path during at least
3.5 times the long PSC message interval, (e.g. at least 17.5
Ryoo, et al. Expires September 29, 2014 [Page 27]
Internet-Draft MPLS-TP LP for ITU-T March 2014
seconds with a default message interval of 5 seconds) and there is
no defect on the protection path: The node MUST alert the operator
and MUST NOT perform any protection switching until the operator
resolves this defect.
13. Security Considerations
This document introduces no new security risks. [RFC6378] points out
that MPLS relies on assumptions about traffic injection difficulty
and assumes that the control plane does not have end-to-end security.
[RFC5920] describes MPLS security issues and generic methods for
securing traffic privacy and integrity. MPLS use should conform such
advice.
14. IANA Considerations
14.1. MPLS PSC Request Registry
In the "Generic Associated Channel (G-ACh) Parameters" registry, IANA
maintains the "MPLS PSC Request Registry".
IANA is requested to assign two new code points from this registry.
The values shall be allocated as follows:
Value Description Reference
----- --------------------- ---------------
2 Reverse Request (this document)
3 Exercise (this document)
14.2. MPLS PSC TLV Registry
In the "Generic Associated Channel (G-ACh) Parameters" registry, IANA
maintains the "MPLS PSC TLV Registry".
This document defines a new value for the Capabilities TLV type in
the "MPLS PSC TLV Registry".
Value Description Reference
------ --------------------- ---------------
TBD Capabilities (this document)
14.3. MPLS PSC Capability Flag Registry
IANA is requested to create and maintain a new registry within the
"Generic Associated Channel (G-ACh) Parameters" registry called "MPLS
PSC Capability Flag Registry". All flags within this registry SHALL
be allocated according to the "Standards Action" procedures as
specified in RFC 5226 [RFC5226].
Ryoo, et al. Expires September 29, 2014 [Page 28]
Internet-Draft MPLS-TP LP for ITU-T March 2014
The length of the flags MUST be a multiple of 4 octets. This
document defines 4 octet flags. Flags greater than 4 octets SHALL be
used only if more than 32 Capabilities need to be defined. Flags
defined in this document are:
Bit Hex Value Capability Reference
---- ---------- ----------------------------------- ---------------
0 0x80000000 priority modification (this document)
1 0x40000000 non-revertive behavior modification (this document)
2 0x20000000 support of MS-W command (this document)
3 0x10000000 support of protection against SD (this document)
4 0x08000000 support of EXER command (this document)
5-31 Unassigned (this document)
15. Acknowledgements
The authors would like to thank Yaacov Weingarten, Yuji Tochio,
Malcolm Betts, Ross Callon, Qin Wu and Xian Zhang for their valuable
comments and suggestions on this document.
We would also like to acknowledge explicit text provided by Loa
Andersson and Adrian Farrel.
16. References
16.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
[RFC5654] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N.,
and S. Ueno, "Requirements of an MPLS Transport Profile",
RFC 5654, September 2009.
[RFC6378] Weingarten, Y., Bryant, S., Osborne, E., Sprecher, N., and
A. Fulignoli, "MPLS Transport Profile (MPLS-TP) Linear
Protection", RFC 6378, October 2011.
16.2. Informative References
[RFC4427] Mannie, E. and D. Papadimitriou, "Recovery (Protection and
Restoration) Terminology for Generalized Multi-Protocol
Label Switching (GMPLS)", RFC 4427, March 2006.
Ryoo, et al. Expires September 29, 2014 [Page 29]
Internet-Draft MPLS-TP LP for ITU-T March 2014
[RFC5920] Fang, L., "Security Framework for MPLS and GMPLS
Networks", RFC 5920, July 2010.
[RFC6372] Sprecher, N. and A. Farrel, "MPLS Transport Profile (MPLS-
TP) Survivability Framework", RFC 6372, September 2011.
[G841] International Telecommunications Union, "Types and
characteristics of SDH network protection architectures",
ITU-T Recommendation G.841, October 1998.
[G873.1] International Telecommunications Union, "Optical Transport
Network (OTN): Linear protection", ITU-T Recommendation
G.873.1, July 2011.
[G8031] International Telecommunications Union, "Ethernet Linear
Protection Switching", ITU-T Recommendation G.8031/Y.1342,
June 2011.
Appendix A. An Example of Out-of-service Scenarios
The sequence diagram shown is an example of the out-of-service
scenarios based on the priority level defined in [RFC6378]. The
first PSC message which differs from the previous PSC message is
shown.
A Z
| |
(1) |-- NR(0,0) ------>| (1)
|<----- NR(0,0) ---|
| |
| |
| (FS issued at Z) | (2)
(3) |<------ FS(1,1) --|
|-- NR(0,1) ------>|
| |
| |
(4) | (SF on P(A<-Z)) |
| |
| |
| (Clear FS at Z) | (5)
(6) | X <- NR(0,0) --|
| |
| |
(1) Each end is in the Normal state, and transmits NR(0,0) messages.
Ryoo, et al. Expires September 29, 2014 [Page 30]
Internet-Draft MPLS-TP LP for ITU-T March 2014
(2) When a FS command is issued at node Z, node Z goes into local
Protecting Administrative state (PA:F:L) and begins transmission of
an FS(1,1) messages.
(3) A remote FS message causes node A to go into remote Protecting
Administrative state (PA:F:R), and node A begins transmitting NR(0,1)
messages.
(4) When node A detects a unidirectional SF-P, node A keeps sending
NR(0,1) message because SF-P is ignored under the PA:F:R state.
(5) When a Clear command is issued at node Z, node Z goes into the
Normal state and begins transmission of NR(0,0) messages.
(6) But, node A cannot receive PSC message because of local
unidirectional SF-P. Because no valid PSC message is received, over
a period of several successive message intervals, the last valid
received message remains applicable and the node A continue to
transmit an NR(0,1) message in the PA:F:R state.
Now, there exists a mismatch between the bridge/selector positions of
node A (transmitting an NR(0,1)) and node Z (transmitting an
NR(0,0)). It results in out-of-service even when there is neither
SF-W nor FS.
Appendix B. An Example of Sequence Diagram Showing the Problem with the
Priority Level of SFc
An example of sequence diagram showing the problem with the priority
level of SFc defined in [RFC6378] is given below. The following
sequence diagram is depicted for the case of bidirectional signal
fails. However, other cases with unidirectional signal fails can
result in the same problem. The first PSC message which differs from
the previous PSC message is shown.
Ryoo, et al. Expires September 29, 2014 [Page 31]
Internet-Draft MPLS-TP LP for ITU-T March 2014
A Z
| |
(1) |-- NR(0,0) ------>| (1)
|<----- NR(0,0) ---|
| |
| |
(2) | (SF on P(A<->Z)) | (2)
|-- SF(0,0) ------>|
|<------ SF(0,0) --|
| |
| |
(3) | (SF on W(A<->Z)) | (3)
| |
| |
(4) | (Clear SF-P) | (4)
| |
| |
(5) | (Clear SF-W) | (5)
| |
| |
(1) Each end is in the Normal state, and transmits NR(0,0) messages.
(2) When SF-P occurs, each node enters into the UA:P:L state and
transmits SF(0,0) messages. Traffic remains on the working path.
(3) When SF-W occurs, each node remains in the UA:P:L state as SF-W
has a lower priority than SF-P. Traffic is still on the working
path. Traffic cannot be delivered as both the working path and the
protection path are experiencing signal fails.
(4) When SF-P is cleared, local "Clear SF-P" request cannot be
presented to the PSC Control Logic, which takes the highest local
request and runs PSC state machine, since the priority of "Clear
SF-P" is lower than that of SF-W. Consequently, there is no change
in state, and the selector and/or bridge keep pointing at the working
path, which has signal fail condition.
Now, traffic cannot be delivered while the protection path is
recovered and available. It should be noted that the same problem
will occur in the case that the sequence of SF-P and SF-W events is
changed.
If we further continue with this sequence to see what will happen
after SF-W is cleared,
(5) When SF-W is cleared, local "Clear SF-W" request can be passed to
the PSC Control Logic as there is no higher priority local input, but
Ryoo, et al. Expires September 29, 2014 [Page 32]
Internet-Draft MPLS-TP LP for ITU-T March 2014
this will be ignored in the PSC Control Logic according to the state
transition definition in [RFC6378]. There will be no change in state
or protocol message transmitted.
As SF-W is now cleared and the selector and/or bridge are still
pointing at the working path, traffic delivery is resumed. However,
each node is in the UA:P:L state and transmitting SF(0,0) message,
while there exists no outstanding request for protection switching.
Moreover, any future legitimate protection switching requests, such
as SF-W, will be rejected as each node thinks the protection path is
unavailable.
Appendix C. Freeze Command
The "Freeze" command applies only to the local node of the protection
group and is not signaled to the remote node. This command freezes
the state of the protection group. Until the Freeze is cleared,
additional local commands are rejected and condition changes and
received PSC information are ignored.
"Clear Freeze" command clears the local freeze. When the Freeze
command is cleared, the state of the protection group is recomputed
based on the persistent condition of the local triggers.
Because the freeze is local, if the freeze is issued at one end only,
a failure of protocol can occur as the other end is open to accept
any operator command or a fault condition.
Appendix D. Operation Examples of the APS Mode
The sequence diagrams shown in this section are only a few examples
of the APS mode operations. The first PSC protocol message which
differs from the previous message is shown. The operation of hold-
off timer is omitted. The Request, FPath and Path fields, whose
values are changed during PSC message exchange are shown. For an
example, SF(1,0) represents an PSC message with the following field
values: Request=SF, FPath=1 and Path=1. The values of the other
fields remain unchanged from the initial configuration. W(A->Z) and
P(A->Z) indicate the working path and the protection path in the
direction of A to Z, respectively.
Example 1. 1:1 bidirectional protection switching (revertive
operation) - Unidirectional SF case
Ryoo, et al. Expires September 29, 2014 [Page 33]
Internet-Draft MPLS-TP LP for ITU-T March 2014
A Z
| |
(1) |<---- NR(0,0)---->| (1)
| |
| |
(2) | (SF on W(Z->A)) |
|---- SF(1,1)----->| (3)
(4) |<----- NR(0,1)----|
| |
| |
(5) | (Clear SF-W) |
|---- WTR(0,1)---->|
/| |
| | |
WTR timer | |
| | |
\| |
(6) |---- NR(0,1)----->| (7)
(8) |<----- NR(0,0)----|
|---- NR(0,0)----->| (9)
| |
(1) The protected domain is operating without any defect, and the
working path is used for delivering the traffic in the Normal state.
(2) SF-W occurs in the Z to A direction. Node A enters into the
PF:W:L state and generates SF(1,1) message. Selector and bridge of
node A are pointing at the protection path.
(3) Upon receiving SF(1,1), node Z sets selector and bridge to the
protection path. As there is no local request in node Z, node Z
generates NR(0,1) message in the PF:W:R state.
(4) Node A confirms that the remote node is also selecting the
protection path.
(5) Node A detects clearing of SF condition, starts the WTR timer,
and sends WTR(0,1) message in the WTR state.
(6) At expiration of the WTR timer, node A sets selector and bridge
to the working path and sends NR(0,1) message.
(7) Node Z is notified that the remote request has been cleared.
Node Z transits to the Normal state and sends NR(0,0) message.
(8) Upon receiving NR(0,0) message, node A transits to the Normal
state and sends NR(0,0) message.
Ryoo, et al. Expires September 29, 2014 [Page 34]
Internet-Draft MPLS-TP LP for ITU-T March 2014
(9) It is confirmed that the remote node is also selecting the
working path.
Example 2. 1:1 bidirectional protection switching (revertive
operation) - Bidirectional SF case - Inconsistent WTR timers
A Z
| |
(1) |<---- NR(0,0)---->| (1)
| |
| |
(2) | (SF on W(A<->Z)) | (2)
|<---- SF(1,1)---->|
| |
| |
(3) | (Clear SF-W) | (3)
|<---- NR(0,1)---->|
(4) |<--- WTR(0,1) --->| (4)
/| |\
| | | |
WTR timer | | WTR timer
| | | |
| | |/
| |<------ NR(0,1)---| (5)
| | |
\| |
(6) |--- NR(0,1)------>|
|<------ NR(0,0)---| (7)
(8) |--- NR(0,0)------>|
| |
(1) Each end is in the Normal state, and transmits NR(0,0) messages.
(2) When SF-W occurs, each node enters into the PF:W:L state and
transmits SF(1,1) messages. Traffic is switched to the protection
path. Upon receiving SF(1,1), each node confirms that the remote
node is also sending and receiving the traffic from the protection
path.
(3) When SF-W is cleared, each node transits to the PF:W:R state and
transmits NR(0,1) messages as the last received message is SF-W.
(4) Upon receiving NR(0,1) messages, each node goes into the WTR
state, starts the WTR timer, and sends the WTR(0,1) messages.
(5) At expiration of the WTR timer in node Z, node Z sends NR(0,1) as
the last received APS message was WTR. When NR(0,1) arrives at node
Ryoo, et al. Expires September 29, 2014 [Page 35]
Internet-Draft MPLS-TP LP for ITU-T March 2014
A, node A maintains the WTR state and keeps sending current WTR
messages as described in the state transition table.
(6) At expiration of the WTR timer in node A, node A sends NR(0,1).
(7) When the NR(0,1) message arrives at node Z, node Z moves to the
Normal state, sets selector and bridge to the working path, and sends
NR(0,0) message.
(8) The received NR(0,0) message causes node A to go to the Normal
state. Now, the traffic is switched back to the working path.
Example 3. 1:1 bidirectional protection switching - R bit mismatch
This example shows that both sides will interwork and the traffic is
protected when one side (node A) is configured as revertive operation
and the other (node Z) is configured as non-revertive operation. The
interworking is covered in the state transition tables.
(revertive) A Z (non-revertive)
| |
(1) |<---- NR(0,0)---->| (1)
| |
| |
(2) | (SF on W(A<->Z)) | (2)
|<---- SF(1,1)---->|
| |
| |
(3) | (Clear SF-W) | (3)
|<---- NR(0,1)---->|
(4) |<----- DNR(0,1)---| (4)
/|-- WTR(0,1)------>|
| |<----- NR(0,1)----| (5)
| | |
WTR timer | |
| | |
| | |
\| |
(6) |--- NR(0,1)------>|
|<------ NR(0,0)---| (7)
(8) |--- NR(0,0)------>|
| |
(1) Each end is in the Normal state, and transmits NR(0,0) messages.
(2) When SF-W occurs, each node enters into the PF:W:L state and
transmits SF(l,l) messages. Traffic is switched to the protection
path. Upon receiving SF(1,1), each node confirms that the remote
Ryoo, et al. Expires September 29, 2014 [Page 36]
Internet-Draft MPLS-TP LP for ITU-T March 2014
node is also sending and receiving the traffic on the protection
path.
(3) When SF-W is cleared, each node transits to the PF:W:R state and
transmits NR(0,1) messages as the last received message is SF-W.
(4) Upon receiving NR(0,1) messages, node A goes into the WTR state,
starts the WTR timer, and sends WTR(0,1) messages. At the same time,
node Z transits to the DNR state and sends DNR(0,1) message.
(5) When the WTR message arrives at node Z, node Z transits to the
WTR state and send NR(0,1) message according to the state transition
table. At the same time, the DNR message arrived at node Z is
ignored according to the state transition table. Therefore, node Z,
which is configured as non-revertive operation, is operating as if in
revertive operation.
(6) At expiration of the WTR timer in node A, node A sends NR(0,1).
(7) When the NR(0,1) message arrives at node Z, node Z moves to the
Normal state, sets selector and bridge to the working path, and sends
NR(0,0) message.
(8) The received NR(0,0) message causes node A to transits to the
Normal state. Now, the traffic is switched back to the working path.
Authors' Addresses
Jeong-dong Ryoo (editor)
ETRI
218 Gajeongno
Yuseong-gu, Daejeon 305-700
South Korea
Phone: +82-42-860-5384
Email: ryoo@etri.re.kr
Eric Gray (editor)
Ericsson
Email: eric.gray@ericsson.com
Ryoo, et al. Expires September 29, 2014 [Page 37]
Internet-Draft MPLS-TP LP for ITU-T March 2014
Huub van Helvoort
Huawei Technologies
Karspeldreef 4,
Amsterdam 1101 CJ
the Netherlands
Phone: +31 20 4300936
Email: huub.van.helvoort@huawei.com
Alessandro D'Alessandro
Telecom Italia
via Reiss Romoli, 274
Torino 10148
Italy
Phone: +39 011 2285887
Email: alessandro.dalessandro@telecomitalia.it
Taesik Cheung
ETRI
218 Gajeongno
Yuseong-gu, Daejeon 305-700
South Korea
Phone: +82-42-860-5646
Email: cts@etri.re.kr
Eric Osborne
Email: eric.osborne@notcom.com
Ryoo, et al. Expires September 29, 2014 [Page 38]
