Internet DRAFT - draft-ietf-v6ops-rfc6555bis
draft-ietf-v6ops-rfc6555bis
Network D. Schinazi
Internet-Draft T. Pauly
Obsoletes: 6555 (if approved) Apple Inc.
Intended status: Standards Track October 25, 2017
Expires: April 28, 2018
Happy Eyeballs Version 2: Better Connectivity Using Concurrency
draft-ietf-v6ops-rfc6555bis-07
Abstract
Many communication protocols operated over the modern Internet use
host names. These often resolve to multiple IP addresses, each of
which may have different performance and connectivity
characteristics. Since specific addresses or address families (IPv4
or IPv6) may be blocked, broken, or sub-optimal on a network, clients
that attempt multiple connections in parallel have a higher chance of
establishing a connection sooner. This document specifies
requirements for algorithms that reduce this user-visible delay and
provides an example algorithm, referred to as "Happy Eyeballs". This
document obsoletes the original algorithm description in [RFC6555].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on April 28, 2018.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
Schinazi & Pauly Expires April 28, 2018 [Page 1]
Internet-Draft Happy Eyeballs v2 October 2017
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Hostname Resolution Query Handling . . . . . . . . . . . . . 4
3.1. Handling Multiple DNS Server Addresses . . . . . . . . . 5
4. Sorting Addresses . . . . . . . . . . . . . . . . . . . . . . 5
5. Connection Attempts . . . . . . . . . . . . . . . . . . . . . 6
6. DNS Answer Changes during Happy Eyeballs Connection Setup . . 7
7. Supporting IPv6-only Networks with NAT64 and DNS64 . . . . . 8
7.1. IPv4 Address Literals . . . . . . . . . . . . . . . . . . 8
7.2. Host Names with Broken AAAA Records . . . . . . . . . . . 9
7.3. Virtual Private Networks . . . . . . . . . . . . . . . . 10
8. Summary of Configurable Values . . . . . . . . . . . . . . . 11
9. Limitations . . . . . . . . . . . . . . . . . . . . . . . . . 11
9.1. Path Maximum Transmission Unit Discovery . . . . . . . . 12
9.2. Application Layer . . . . . . . . . . . . . . . . . . . . 12
9.3. Hiding Operational Issues . . . . . . . . . . . . . . . . 12
10. Security Considerations . . . . . . . . . . . . . . . . . . . 12
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
12. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 12
13. References . . . . . . . . . . . . . . . . . . . . . . . . . 13
13.1. Normative References . . . . . . . . . . . . . . . . . . 13
13.2. Informative References . . . . . . . . . . . . . . . . . 14
Appendix A. Differences from RFC6555 . . . . . . . . . . . . . . 14
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15
Schinazi & Pauly Expires April 28, 2018 [Page 2]
Internet-Draft Happy Eyeballs v2 October 2017
1. Introduction
Many communication protocols operated over the modern Internet use
host names. These often resolve to multiple IP addresses, each of
which may have different performance and connectivity
characteristics. Since specific addresses or address families (IPv4
or IPv6) may be blocked, broken, or sub-optimal on a network, clients
that attempt multiple connections in parallel have a higher chance of
establishing a connection sooner. This document specifies
requirements for algorithms that reduce this user-visible delay and
provides an example algorithm.
This document defines the algorithm for "Happy Eyeballs", a technique
of reducing user-visible delays on dual-stack hosts. This definition
obsoletes the original description in [RFC6555]. Now that this
approach has been deployed at scale and measured for several years,
the algorithm specification can be refined to improve its reliability
and generalization.
The Happy Eyeballs algorithm of racing resolved addresses has several
stages of ordering and racing to avoid delays to the user whenever
possible, while preferring the use of IPv6. This document discusses
how to handle DNS queries when starting a connection on a dual-stack
client, how to create an ordered list of destination addresses to
which to attempt connections, and how to race the connection
attempts.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119] [RFC8174] when, and only when, they appear in all capitals,
as shown here.
2. Overview
This document defines a method of connection establishment, named
"Happy Eyeballs Connection Setup". This approach has several
distinct phases:
1. Initiation of asynchronous DNS queries [Section 3]
2. Sorting of resolved destination addresses [Section 4]
3. Initiation of asynchronous connection attempts [Section 5]
4. Establishment of one connection, which cancels all other attempts
Schinazi & Pauly Expires April 28, 2018 [Page 3]
Internet-Draft Happy Eyeballs v2 October 2017
Note that this document assumes that the host destination address
preference policy favors IPv6 over IPv4. IPv6 has many desirable
properties designed to be improvements over IPv4 [RFC8200]. If the
host is configured to have a different preference, the
recommendations in this document can be easily adapted.
3. Hostname Resolution Query Handling
When a client has both IPv4 and IPv6 connectivity, and is trying to
establish a connection with a named host, it needs to send out both
AAAA and A DNS queries. Both queries SHOULD be made as soon after
one another as possible, with the AAAA query made first, immediately
followed by the A query.
Implementations SHOULD NOT wait for both families of answers to
return before attempting connection establishment. If one query
fails to return, or takes significantly longer to return, waiting for
the second address family can significantly delay the connection
establishment of the first one. Therefore, the client SHOULD treat
DNS resolution as asynchronous. Note that if the platform does not
offer an asynchronous DNS API, this behavior can be simulated by
making two separate synchronous queries on different threads, one per
address family.
The algorithm proceeds as follows: if a positive AAAA response (a
response with at least one valid AAAA record) is received first, the
first IPv6 connection attempt is immediately started. If a positive
A response is received first due to reordering, the client SHOULD
wait for a short time for the AAAA response to ensure preference is
given to IPv6 (it is common for the AAAA response to follow the A
response by a few milliseconds). This delay will be referred to as
the "Resolution Delay". The recommended value for the Resolution
Delay is 50 milliseconds. If a positive AAAA response is received
within the Resolution Delay period, the client immediately starts the
IPv6 connection attempt. If a negative AAAA response (no error, no
data) is received within the Resolution Delay period or the AAAA
response has not been received by the end of the Resolution Delay
period, the client SHOULD proceed to Sorting Addresses [Section 4]
and staggered connection attempts [Section 5] using any IPv4
addresses returned so far. If the AAAA response arrives while these
connection attempts are in progress, but before any connection has
been established, then the newly received IPv6 addresses are
incorporated into the list of available candidate addresses
[Section 6] and the process of connection attempts will continue with
the IPv6 addresses added, until one connection is established.
Schinazi & Pauly Expires April 28, 2018 [Page 4]
Internet-Draft Happy Eyeballs v2 October 2017
3.1. Handling Multiple DNS Server Addresses
If multiple DNS server addresses are configured for the current
network, the client may have the option of sending its DNS queries
over IPv4 or IPv6. In keeping with the Happy Eyeballs approach,
queries SHOULD be sent over IPv6 first (note that this is not
referring to the sending of AAAA or A queries, but rather the address
of the DNS server itself and IP version used to transport DNS
messages). If DNS queries sent to the IPv6 address do not receive
responses, that address may be marked as penalized, and queries can
be sent to other DNS server addresses.
As native IPv6 deployments become more prevalent, and IPv4 addresses
are exhausted, it is expected that IPv6 connectivity will have
preferential treatment within networks. If a DNS server is
configured to be accessible over IPv6, IPv6 should be assumed to be
the preferred address family.
Client systems SHOULD NOT have an explicit limit to the number of DNS
servers that can be configured, either manually or by the network.
If such a limit is required by hardware limitations, the client
SHOULD use at least one address from each address family from the
available list.
4. Sorting Addresses
Before attempting to connect to any of the resolved destination
addresses, the client should define the order in which to start the
attempts. Once the order has been defined, the client can use a
simple algorithm for racing each option after a short delay
[Section 5]. It is important that the ordered list involves all
addresses from both families that have been received by this point,
as this allows the client to get the racing effect of Happy Eyeballs
for the entire list, not just the first IPv4 and first IPv6
addresses.
First, the client MUST sort the addresses received up to this point
using Destination Address Selection ([RFC6724], Section 6).
Schinazi & Pauly Expires April 28, 2018 [Page 5]
Internet-Draft Happy Eyeballs v2 October 2017
If the client is stateful and has history of expected round-trip
times (RTT) for the routes to access each address, it SHOULD add a
Destination Address Selection rule between rules 8 and 9 that prefers
addresses with lower RTTs. If the client keeps track of which
addresses it has used in the past, it SHOULD add another destination
address selection rule between the RTT rule and rule 9, which prefers
used addresses over unused ones. This helps servers that use the
client's IP address during authentication, as is the case for TCP
Fast Open [RFC7413] and some HTTP cookies. This historical data MUST
NOT be used across different network interfaces, and SHOULD be
flushed whenever a device changes the network to which it is
attached.
Next, the client SHOULD modify the ordered list to interleave address
families. Whichever address family is first in the list should be
followed by an address of the other address family; that is, if the
first address in the sorted list is IPv6, then the first IPv4 address
should be moved up in the list to be second in the list. An
implementation MAY want to favor one address family more by allowing
multiple addresses of that family to be attempted before trying the
other family. The number of contiguous addresses of the first
address family will be referred to as the "First Address Family
Count", and can be a configurable value. This is performed to avoid
waiting through a long list of addresses from a given address family
if connectivity over that address family is impaired.
Note that the address selection described in this section only
applies to destination addresses; Source Address Selection
([RFC6724], Section 5) is performed once per destination address and
is out of scope of this document.
5. Connection Attempts
Once the list of addresses received up to this point has been
constructed, the client will attempt to make connections. In order
to avoid unreasonable network load, connection attempts SHOULD NOT be
made simultaneously. Instead, one connection attempt to a single
address is started first, followed by the others in the list, one at
a time. Starting a new connection attempt does not affect previous
attempts, as multiple connection attempts may occur in parallel.
Once one of the connection attempts succeeds (generally when the TCP
handshake completes), all other connections attempts that have not
yet succeeded SHOULD be cancelled. Any address that was not yet
attempted as a connection SHOULD be ignored. At that time, the
asynchronous DNS query MAY be cancelled as new addresses will not be
used for this connection. However, the DNS client resolver SHOULD
still process DNS replies from the network for a short period of time
Schinazi & Pauly Expires April 28, 2018 [Page 6]
Internet-Draft Happy Eyeballs v2 October 2017
(recommended to be 1 second), as they will populate the DNS cache and
can be used for subsequent connections.
A simple implementation can have a fixed delay for how long to wait
before starting the next connection attempt. This delay is referred
to as the "Connection Attempt Delay". One recommended value for a
default delay is 250 milliseconds. A more nuanced implementation's
delay should correspond to the time when the previous attempt is
sending its second TCP SYN, based on TCP's retransmission timer
[RFC6298]. If the client has historical RTT data gathered from other
connections to the same host or prefix, it can use this information
to influence its delay. Note that this algorithm should only try to
approximate the time of the first SYN retransmission, and not any
further retransmissions which may be influenced by exponential timer
back off.
The Connection Attempt Delay MUST have a lower bound, especially if
it is computed using historical data. More specifically, a
subsequent connection MUST NOT be started within 10 milliseconds of
the previous attempt. The recommended minimum value is 100
milliseconds, which is referred to as the "Minimum Connection Attempt
Delay". This minimum value is required to avoid congestion collapse
in the presence of high packet loss rates. The Connection Attempt
Delay SHOULD have an upper bound, referred to as the "Maximum
Connection Attempt Delay". The current recommended value is 2
seconds.
6. DNS Answer Changes during Happy Eyeballs Connection Setup
If, during the course of connection establishment, the DNS answers
change either by adding resolved addresses (for example, due to DNS
push notifications [DNS-PUSH]), or removing previously resolved
addresses (for example, due to expiry of the TTL on that DNS record),
the client should react based on its current progress.
If an address is removed from the list that already had a connection
attempt started, the connection attempt SHOULD NOT be cancelled, but
rather be allowed to continue. If the removed address had not yet
had a connection attempt started, it SHOULD be removed from the list
of addresses to try.
If an address is added to the list, it should be sorted into the list
of addresses not yet attempted according to the rules above
(Section 4).
Schinazi & Pauly Expires April 28, 2018 [Page 7]
Internet-Draft Happy Eyeballs v2 October 2017
7. Supporting IPv6-only Networks with NAT64 and DNS64
While many IPv6 transition protocols have been standardized and
deployed, most are transparent to client devices. The combined use
of NAT64 [RFC6146] and DNS64 [RFC6147] is a popular solution that is
being deployed and requires changes in client devices. One possible
way to handle these networks is for the client device networking
stack to implement 464XLAT [RFC6877]. 464XLAT has the advantage of
not requiring changes to user space software, however it requires
per-packet translation if the application is using IPv4 literals and
does not encourage client application software to support native
IPv6. On platforms that do not support 464XLAT, the Happy Eyeballs
engine SHOULD follow the recommendations in this section to properly
support IPv6-only networks with NAT64 and DNS64.
The features described in this section SHOULD only be enabled when
the host detects one of these networks. A simple heuristic to
achieve that is to check if the network offers routable IPv6
addressing, does not offer routable IPv4 addressing, and offers a DNS
resolver address.
7.1. IPv4 Address Literals
If client applications or users wish to connect to IPv4 address
literals, the Happy Eyeballs engine will need to perform NAT64
address synthesis for them. The solution is similar to "Bump-in-the-
Host" [RFC6535] but is implemented inside the Happy Eyeballs library.
When an IPv4 address is passed in to the library instead of a host
name, the device queries the network for the NAT64 prefix using
"Discovery of the IPv6 Prefix Used for IPv6 Address Synthesis"
[RFC7050] then synthesizes an appropriate IPv6 address (or several)
using the encoding described in "IPv6 Addressing of IPv4/IPv6
Translators" [RFC6052]. The synthesized addresses are then inserted
into the list of addresses as if they were results from DNS queries;
connection attempts follow the algorithm described above (Section 5).
Schinazi & Pauly Expires April 28, 2018 [Page 8]
Internet-Draft Happy Eyeballs v2 October 2017
7.2. Host Names with Broken AAAA Records
At the time of writing, there exist a small but non negligible number
of host names that resolve to valid A records and broken AAAA
records, which we define as AAAA records that contain seemingly valid
IPv6 addresses but those addresses never reply when contacted on the
usual ports. These can be for example caused by:
o Mistyping of the IPv6 address in the DNS zone configuration
o Routing black holes
o Service outages
While an algorithm complying with the other sections of this document
would correctly handle such host names on a dual-stack network, they
will not necessarily function correctly on IPv6-only networks with
NAT64 and DNS64. Since DNS64 recursive resolvers rely on the
authoritative name servers sending negative ("no error no answer")
responses for AAAA records in order to synthesize, they will not
synthesize records for these particular host names, and will instead
pass through the broken AAAA record.
In order to support these scenarios, the client device needs to query
the DNS for the A record then perform local synthesis. Since these
types of host names are rare, and in order to minimize load on DNS
servers, this A query should only be performed when the client has
given up on the AAAA records it initially received. This can be
achieved by using a longer timeout, referred to as the "Last Resort
Local Synthesis Delay" and recommended to be 2 seconds. The timer is
started when the last connection attempt is fired. If no connection
attempt has succeeded when this timer fires, the device queries the
DNS for the IPv4 address and on reception of a valid A record, treats
it as if it were provided by the application (Section 7.1).
Schinazi & Pauly Expires April 28, 2018 [Page 9]
Internet-Draft Happy Eyeballs v2 October 2017
7.3. Virtual Private Networks
Some Virtual Private Networks (VPN) may be configured to handle DNS
queries from the device. The configuration could encompass all
queries, or a subset such as "*.internal.example.com". These VPNs
can also be configured to only route part of the IPv4 address space,
such as 192.0.2.0/24. However, if an internal hostname resolves to
an external IPv4 address, these can cause issues if the underlying
network is IPv6-only. As an example, let's assume that
"www.internal.example.com" has exactly one A record, 198.51.100.42,
and no AAAA records. The client will send the DNS query to the
company's recursive resolver and that resolver will reply with these
records. The device now only has an IPv4 address to connect to, and
no route to that address. Since the company's resolver does not know
the NAT64 prefix of the underlying network, it cannot synthesize the
address. Similarly, the underlying network's DNS64 recursive
resolver does not know the company's internal addresses, so it cannot
resolve the hostname. Because of this, the client device needs to
resolve the A record using the company's resolver then locally
synthesize an IPv6 address, as if the resolved IPv4 address were
provided by the application (Section 7.1).
Schinazi & Pauly Expires April 28, 2018 [Page 10]
Internet-Draft Happy Eyeballs v2 October 2017
8. Summary of Configurable Values
The values that may be configured as defaults on a client for use in
Happy Eyeballs are as follows:
o Resolution Delay (Section 3): The time to wait for a AAAA response
after receiving an A response. Recommended to be 50 milliseconds.
o First Address Family Count (Section 4): The number of addresses
belonging to the first address family (such as IPv6) that should
be attempted before attempting another address family.
Recommended to be 1, or 2 to more aggressively favor one address
family.
o Connection Attempt Delay (Section 5): The time to wait between
connection attempts in the absence of RTT data. Recommended to be
250 milliseconds.
o Minimum Connection Attempt Delay (Section 5): The minimum time to
wait between connection attempts. Recommended to be 100
milliseconds. MUST NOT be less than 10 milliseconds.
o Maximum Connection Attempt Delay (Section 5): The maximum time to
wait between connection attempts. Recommended to be 2 seconds.
o Last Resort Local Synthesis Delay (Section 7.2): The time to wait
after starting the last IPv6 attempt and before sending the A
query. Recommended to be 2 seconds.
The delay values described in this section were determined
empirically by measuring the timing of connections on a very wide set
of production devices. They were picked to reduce wait times noticed
by users while minimizing load on the network. As time passes, it is
expected that the properties of networks will evolve. For that
reason, it is expected that these values will change over time.
Implementors should feel welcome to use different values without
changing this specification. Since IPv6 issues are expected to be
less common, the delays SHOULD be increased with time as client
software is updated.
9. Limitations
Happy Eyeballs will handle initial connection failures at the TCP/IP
layer, however other failures or performance issues may still affect
the chosen connection.
Schinazi & Pauly Expires April 28, 2018 [Page 11]
Internet-Draft Happy Eyeballs v2 October 2017
9.1. Path Maximum Transmission Unit Discovery
Since Happy Eyeballs is only active during the initial handshake and
TCP does not pass the initial handshake, issues related to MTU can be
masked and go unnoticed during Happy Eyeballs. Solving this issue is
out of scope of this document. One solution is to use Packetization
Layer Path MTU Discovery [RFC4821].
9.2. Application Layer
If the DNS returns multiple addresses for different application
servers, the application itself may not be operational and functional
on all of them. Common examples include Transport Layer Security
(TLS) and the Hypertext Transport Protocol (HTTP).
9.3. Hiding Operational Issues
It has been observed in practice that Happy Eyeballs can hide issues
in networks. For example, if a misconfiguration causes IPv6 to
consistently fail on a given network while IPv4 is still functional,
Happy Eyeballs may impair the operator's ability to notice the issue.
It is recommended that network operators deploy external means of
monitoring to ensure functionality of all address families.
10. Security Considerations
Note that applications should not rely upon a stable hostname-to-
address mapping to ensure any security properties, since DNS results
may change between queries. Happy Eyeballs may make it more likely
that subsequent connections to a single hostname use different IP
addresses.
11. IANA Considerations
This memo includes no request to IANA.
12. Acknowledgments
The authors thank Dan Wing, Andrew Yourtchenko, and everyone else who
worked on the original Happy Eyeballs design [RFC6555], Josh
Graessley, Stuart Cheshire, and the rest of team at Apple that helped
implement and instrument this algorithm, and Jason Fesler and Paul
Saab who helped measure and refine this algorithm. The authors would
also like to thank Fred Baker, Nick Chettle, Lorenzo Colitti, Igor
Gashinsky, Geoff Huston, Jen Linkova, Paul Hoffman, Philip Homburg,
Warren Kumari, Erik Nygren, Jordi Palet Martinez, Rui Paulo, Stephen
Strowes, Jinmei Tatuya, Dave Thaler, Joe Touch and James Woodyatt for
their input and contributions.
Schinazi & Pauly Expires April 28, 2018 [Page 12]
Internet-Draft Happy Eyeballs v2 October 2017
13. References
13.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, DOI 10.17487/RFC4821, March 2007,
<https://www.rfc-editor.org/info/rfc4821>.
[RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X.
Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052,
DOI 10.17487/RFC6052, October 2010,
<https://www.rfc-editor.org/info/rfc6052>.
[RFC6146] Bagnulo, M., Matthews, P., and I. van Beijnum, "Stateful
NAT64: Network Address and Protocol Translation from IPv6
Clients to IPv4 Servers", RFC 6146, DOI 10.17487/RFC6146,
April 2011, <https://www.rfc-editor.org/info/rfc6146>.
[RFC6147] Bagnulo, M., Sullivan, A., Matthews, P., and I. van
Beijnum, "DNS64: DNS Extensions for Network Address
Translation from IPv6 Clients to IPv4 Servers", RFC 6147,
DOI 10.17487/RFC6147, April 2011,
<https://www.rfc-editor.org/info/rfc6147>.
[RFC6298] Paxson, V., Allman, M., Chu, J., and M. Sargent,
"Computing TCP's Retransmission Timer", RFC 6298,
DOI 10.17487/RFC6298, June 2011,
<https://www.rfc-editor.org/info/rfc6298>.
[RFC6535] Huang, B., Deng, H., and T. Savolainen, "Dual-Stack Hosts
Using "Bump-in-the-Host" (BIH)", RFC 6535,
DOI 10.17487/RFC6535, February 2012,
<https://www.rfc-editor.org/info/rfc6535>.
[RFC6555] Wing, D. and A. Yourtchenko, "Happy Eyeballs: Success with
Dual-Stack Hosts", RFC 6555, DOI 10.17487/RFC6555, April
2012, <https://www.rfc-editor.org/info/rfc6555>.
[RFC6724] Thaler, D., Ed., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version 6
(IPv6)", RFC 6724, DOI 10.17487/RFC6724, September 2012,
<https://www.rfc-editor.org/info/rfc6724>.
Schinazi & Pauly Expires April 28, 2018 [Page 13]
Internet-Draft Happy Eyeballs v2 October 2017
[RFC7050] Savolainen, T., Korhonen, J., and D. Wing, "Discovery of
the IPv6 Prefix Used for IPv6 Address Synthesis",
RFC 7050, DOI 10.17487/RFC7050, November 2013,
<https://www.rfc-editor.org/info/rfc7050>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
13.2. Informative References
[DNS-PUSH]
Pusateri, T. and S. Cheshire, "DNS Push Notifications",
Work in Progress, draft-ietf-dnssd-push, March 2017.
[RFC6877] Mawatari, M., Kawashima, M., and C. Byrne, "464XLAT:
Combination of Stateful and Stateless Translation",
RFC 6877, DOI 10.17487/RFC6877, April 2013,
<https://www.rfc-editor.org/info/rfc6877>.
[RFC7413] Cheng, Y., Chu, J., Radhakrishnan, S., and A. Jain, "TCP
Fast Open", RFC 7413, DOI 10.17487/RFC7413, December 2014,
<https://www.rfc-editor.org/info/rfc7413>.
[RFC8200] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", STD 86, RFC 8200,
DOI 10.17487/RFC8200, July 2017,
<https://www.rfc-editor.org/info/rfc8200>.
Appendix A. Differences from RFC6555
"Happy Eyeballs: Success with Dual-Stack Hosts" [RFC6555] mostly
concentrates on how to stagger connections to a hostname that has an
AAAA and an A record. This document additionally discusses:
o how to perform DNS queries to obtain these addresses
o how to handle multiple addresses from each address family
o how to handle DNS updates while connections are being raced
o how to leverage historical information
o how to support IPv6-only networks with NAT64 and DNS64
Note that a simple implementation of the algorithm described in this
document is still compliant with the previous specification
Schinazi & Pauly Expires April 28, 2018 [Page 14]
Internet-Draft Happy Eyeballs v2 October 2017
[RFC6555]. Implementations should take the new considerations into
account when applicable to optimize their behavior.
Authors' Addresses
David Schinazi
Apple Inc.
1 Infinite Loop
Cupertino, California 95014
US
Email: dschinazi@apple.com
Tommy Pauly
Apple Inc.
1 Infinite Loop
Cupertino, California 95014
US
Email: tpauly@apple.com
Schinazi & Pauly Expires April 28, 2018 [Page 15]
