rfc2514









Network Working Group                                           M. Noto
Request for Comments: 2514                                         3Com
Category: Standards Track                                    E. Spiegel
                                                          Cisco Systems
                                                              K. Tesink
                                                               Bellcore
                                                                Editors
                                                          February 1999


        Definitions of Textual Conventions and OBJECT-IDENTITIES
                           for ATM Management

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   Table of Contents

   1 Introduction ..........................................    2
   2 Definitions ...........................................    3
   3 Acknowledgments .......................................   17
   4 References ............................................   17
   5 Security Considerations ...............................   17
   6 Authors' Addresses ....................................   18
   7 Intellectual Property .................................   19
   8 Full Copyright Statement ..............................   20

Abstract

   This memo describes Textual Conventions and OBJECT-IDENTITIES used
   for managing ATM-based interfaces, devices, networks and services.

1.  Introduction

   This memo describes Textual Conventions and OBJECT-IDENTITIES used
   for managing ATM-based interfaces, devices, networks and services.






Noto, et. al.               Standards Track                     [Page 1]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


   When designing a MIB module, it is often useful to define new types
   similar to those defined in the SMI.  In comparison to a type defined
   in the SMI, each of these new types has a different name, a similar
   syntax, but a more precise semantics.  These newly defined types are
   termed textual conventions, and are used for the convenience of
   humans reading the MIB module.  This is done through Textual
   Conventions as defined in RFC1903 [1].  It is the purpose of this
   document to define the set of textual conventions available to ATM
   MIB modules.

   When designing MIB modules, it is also often useful to register
   further properties with object identifier assignments so that they
   can be further used by other MIB modules.  This is done through the
   OBJECT-IDENTITY macro defined in RFC1902 [2].  This document defines
   OBJECT-IDENTITIES available to ATM MIB modules.

   Note that for organizational purposes OBJECT IDENTITIES previously
   defined in RFC1695 have been moved to this specification and no
   longer appear in the revision of RFC1695 [3]. However, the original
   OBJECT IDENTIFIERs have been preserved.

   For an introduction to the concepts of ATM connections, see [3].

2.  Definitions

     ATM-TC-MIB DEFINITIONS ::= BEGIN

     IMPORTS
        MODULE-IDENTITY, OBJECT-IDENTITY,
        TimeTicks, mib-2
            FROM SNMPv2-SMI
        TEXTUAL-CONVENTION
            FROM SNMPv2-TC;


     atmTCMIB MODULE-IDENTITY
          LAST-UPDATED "9810190200Z"
          ORGANIZATION "IETF AToMMIB Working Group"
          CONTACT-INFO
            "          Michael Noto
              Postal:  3Com Corporation
                       5400 Bayfront Plaza, M/S 3109
                       Santa Clara, CA 95052
                       USA
              Tel:     +1 408 326 2218
              E-mail:  mike_noto@3com.com

                       Ethan Mickey Spiegel



Noto, et. al.               Standards Track                     [Page 2]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


              Postal:  Cisco Systems
                       170 W. Tasman Dr.
                       San Jose, CA 95134
                       USA
              Tel:     +1 408 526 6408
              E-mail:  mspiegel@cisco.com

                       Kaj Tesink
              Postal:  Bellcore
                       331 Newman Springs Road
                       Red Bank, NJ 07701
                       USA
              Tel:     +1 732 758 5254
              Fax:     +1 732 758 4177
              E-mail:  kaj@bellcore.com"
          DESCRIPTION
           "This MIB Module provides Textual Conventions
           and OBJECT-IDENTITY Objects to be used by
           ATM systems."
          ::= { mib-2 37 3 } -- atmMIB 3 (see [3])

     -- The Textual Conventions defined below are organized
     -- alphabetically


     AtmAddr ::= TEXTUAL-CONVENTION
             DISPLAY-HINT "1x"
             STATUS  current
             DESCRIPTION
                 "An ATM address. The semantics are implied by
                 the length. The address types are: - no
                 address (0 octets) - E.164 (8 octets) - NSAP
                 (20 octets) In addition, when subaddresses
                 are used the AtmAddr may represent the
                 concatenation of address and subaddress. The
                 associated address types are: - E.164, E.164
                 (16 octets) - E.164, NSAP (28 octets) - NSAP,
                 NSAP (40 octets) Address lengths other than
                 defined in this definition imply address
                 types defined elsewhere.  Note: The E.164
                 address is encoded in BCD format."
            SYNTAX   OCTET STRING (SIZE(0..40))


    AtmConnCastType ::= TEXTUAL-CONVENTION
            STATUS  current
            DESCRIPTION
              "The type of topology of a connection (point-



Noto, et. al.               Standards Track                     [Page 3]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


              to-point, point-to-multipoint). In the case
              of point-to-multipoint, the orientation of
              this VPL or VCL in the connection.
              On a host:
              - p2mpRoot indicates that the host
                is the root of the p2mp connection.
              - p2mpLeaf indicates that the host
                is a leaf of the p2mp connection.
              On a switch interface:
              - p2mpRoot indicates that cells received
                by the switching fabric from the interface
                are from the root of the p2mp connection.
              - p2mpLeaf indicates that cells transmitted
                to the interface from the switching fabric
                are to the leaf of the p2mp connection."
            SYNTAX   INTEGER {
               p2p(1),
               p2mpRoot(2),
               p2mpLeaf(3)
               }

    AtmConnKind ::= TEXTUAL-CONVENTION
            STATUS  current
            DESCRIPTION
                "The type of call control used for an ATM
                connection at a particular interface. The use
                is as follows:
                   pvc(1)
                      Virtual link of a PVC. Should not be
                      used for an PVC/SVC (i.e., Soft PVC)
                      crossconnect.
                   svcIncoming(2)
                      Virtual link established after a
                      received signaling request to setup
                      an SVC.
                   svcOutgoing(3)
                      Virtual link established after a
                      transmitted or forwarded signaling
                      request to setup an SVC.
                   spvcInitiator(4)
                      Virtual link at the PVC side of an
                      SVC/PVC crossconnect, where the
                      switch is the initiator of the Soft PVC
                      setup.
                   spvcTarget(5)
                      Virtual link at the PVC side of an
                      SVC/PVC crossconnect, where the
                      switch is the target of the Soft PVC



Noto, et. al.               Standards Track                     [Page 4]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


                      setup.

                For PVCs, a pvc virtual link is always cross-
                connected to a pvc virtual link.

                For SVCs, an svcIncoming virtual link is always cross-
                connected to an svcOutgoing virtual link.

For Soft PVCs, an spvcInitiator is either cross-connected to
an svcOutgoing or an spvcTarget, and an spvcTarget is either
cross-connected to an svcIncoming or an spvcInitiator."
        SYNTAX   INTEGER {
           pvc(1),
           svcIncoming(2),
           svcOutgoing(3),
           spvcInitiator(4),
           spvcTarget(5)
           }

    AtmIlmiNetworkPrefix ::= TEXTUAL-CONVENTION
        STATUS   current
        DESCRIPTION
            "A network prefix used for ILMI address
            registration.  In the case of ATM endsystem
            addresses (AESAs), the network prefix is the first
            13 octets of the address which includes the AFI,
            IDI, and HO-DSP fields.  In the case of native
            E.164 addresses, the network prefix is the entire
            E.164 address encoded in 8 octets, as if it were
            an E.164 IDP in an ATM endsystem address
            structure."
        REFERENCE
            "ATM Forum, Integrated Local Management Interface
               (ILMI) Specification, Version 4.0,
               af-ilmi-0065.000, September 1996, Section 9
             ATM Forum, ATM User-Network Interface Signalling
               Specification, Version 4.0 (UNI 4.0),
               af-sig-0061.000, June 1996, Section 3"
        SYNTAX   OCTET STRING (SIZE(8|13))

AtmInterfaceType ::= TEXTUAL-CONVENTION
        STATUS       current
        DESCRIPTION
            "The connection setup procedures used for the
            identified interface.

            Other: Connection setup procedures other than
               those listed below.



Noto, et. al.               Standards Track                     [Page 5]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


            Auto-configuration:
               Indicates that the connection setup
               procedures are to be determined dynamically,
               or that determination has not yet been
               completed. One such mechanism is via ATM
               Forum ILMI auto-configuration procedures.

            ITU-T DSS2:
            -  ITU-T Recommendation Q.2931, Broadband
               Integrated Service Digital Network (B-ISDN)
               Digital Subscriber Signalling System No.2
               (DSS2) User-Network Interface (UNI) Layer 3
               Specification for Basic Call/Connection
               Control (September 1994)
            -  ITU-T Draft Recommendation Q.2961,
               B-ISDN DSS 2 Support of Additional Traffic
               Parameters (May 1995)

            -  ITU-T Draft Recommendation Q.2971,
               B-ISDN DSS 2 User Network Interface Layer 3
               Specification for Point-to-multipoint
               Call/connection Control (May 1995)

            ATM Forum UNI 3.0:
               ATM Forum, ATM User-Network Interface,
               Version 3.0 (UNI 3.0) Specification,
               (1994).

            ATM Forum UNI 3.1:
               ATM Forum, ATM User-Network Interface,
               Version 3.1 (UNI 3.1) Specification,
               (November 1994).

            ATM Forum UNI Signalling 4.0:
               ATM Forum, ATM User-Network Interface (UNI)
               Signalling Specification Version 4.0,
               af-sig-0061.000 (June 1996).

            ATM Forum IISP (based on UNI 3.0 or UNI 3.1) :
               Interim Inter-switch Signaling Protocol
               (IISP) Specification, Version 1.0,
               af-pnni-0026.000, (December 1994).

            ATM Forum PNNI 1.0 :
               ATM Forum, Private Network-Network Interface
               Specification, Version 1.0, af-pnni-0055.000,
               (March 1996).




Noto, et. al.               Standards Track                     [Page 6]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


            ATM Forum B-ICI:
               ATM Forum, B-ICI Specification, Version 2.0,
               af-bici-0013.002, (November 1995).

            ATM Forum UNI PVC Only:
               An ATM Forum compliant UNI with the
               signalling disabled.
            ATM Forum NNI PVC Only:
               An ATM Forum compliant NNI with the
               signalling disabled."
        SYNTAX  INTEGER  {
                  other(1),
                  autoConfig(2),
                  ituDss2(3),
                  atmfUni3Dot0(4),
                  atmfUni3Dot1(5),
                  atmfUni4Dot0(6),
                  atmfIispUni3Dot0(7),
                  atmfIispUni3Dot1(8),
                  atmfIispUni4Dot0(9),
        atmfPnni1Dot0(10),
        atmfBici2Dot0(11),
        atmfUniPvcOnly(12),
        atmfNniPvcOnly(13)  }

AtmServiceCategory ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The service category for a connection."
        REFERENCE
            "ATM Forum Traffic Management Specification,
            Version 4.0, af-tm-0056.000, June 1996."
        SYNTAX   INTEGER {
           other(1),   -- none of the following
           cbr(2),     -- constant bit rate
           rtVbr(3),   -- real-time variable bit rate
           nrtVbr(4),  -- non real-time variable bit rate
           abr(5),     -- available bit rate
           ubr(6)      -- unspecified bit rate
           }

AtmSigDescrParamIndex ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The value of this object identifies a row in the
            atmSigDescrParamTable. The value 0 signifies that
            none of the signalling parameters defined in the
            atmSigDescrParamTable are applicable."



Noto, et. al.               Standards Track                     [Page 7]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        SYNTAX  INTEGER (0..2147483647)

AtmTrafficDescrParamIndex ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The value of this object identifies a row in the
            atmTrafficDescrParamTable.  The value 0 signifies
            that no row has been identified."
        SYNTAX  INTEGER (0..2147483647)

AtmVcIdentifier ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The VCI value for a VCL. The maximum VCI value
            cannot exceed the value allowable by
            atmInterfaceMaxVciBits defined in ATM-MIB."
        SYNTAX   INTEGER (0..65535)

AtmVpIdentifier ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The VPI value for a VPL or VCL. The value VPI=0
            is only allowed for a VCL. For ATM UNIs supporting
            VPCs the VPI value ranges from 0 to 255.  The VPI
            value 0 is supported for ATM UNIs conforming to
            the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs)
            specification. For ATM UNIs supporting VCCs the
            VPI value ranges from 0 to 255.  For ATM NNIs the
            VPI value ranges from 0 to 4095.  The maximum VPI
            value cannot exceed the value allowable by
            atmInterfaceMaxVpiBits defined in ATM-MIB."
        SYNTAX    INTEGER (0..4095)

AtmVorXAdminStatus ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The value determines the desired administrative
            status of a virtual link or cross-connect. The up
            and down states indicate that the traffic flow is
            enabled or disabled respectively on the virtual
            link or cross-connect."
        SYNTAX   INTEGER {
           up(1),
           down(2)
            }

AtmVorXLastChange ::= TEXTUAL-CONVENTION
        STATUS  current



Noto, et. al.               Standards Track                     [Page 8]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        DESCRIPTION
            "The value of MIB II's sysUpTime at the time a
            virtual link or cross-connect entered its current
            operational state. If the current state was
            entered prior to the last re-initialization of the
            agent then this object contains a zero value."
        SYNTAX   TimeTicks

AtmVorXOperStatus ::= TEXTUAL-CONVENTION
        STATUS  current
        DESCRIPTION
            "The value determines the operational status of a
            virtual link or cross-connect. The up and down
            states indicate that the traffic flow is enabled
            or disabled respectively on the virtual link or
            cross-connect. The unknown state indicates that
            the state of it cannot be determined. The state
            will be down or unknown if the supporting ATM
            interface(s) is down or unknown respectively."
        SYNTAX   INTEGER {
           up(1),
           down(2),
           unknown(3)
           }




-- OBJECT-IDENTITIES:

-- The following atmTrafficDescriptorTypes has been moved
-- from RFC1695 and no longer appear in the revision of
-- RFC1695[3].

atmTrafficDescriptorTypes OBJECT IDENTIFIER ::= {mib-2 37 1 1}
                                            -- atmMIBObjects
                                            -- See [3].

-- All other and new OBJECT IDENTITIES
-- are defined under the following subtree:

    atmObjectIdentities OBJECT IDENTIFIER ::= {atmTCMIB 1}

-- The following values are defined for use as
-- possible values of the ATM traffic descriptor type.

atmNoTrafficDescriptor  OBJECT-IDENTITY
    STATUS  deprecated



Noto, et. al.               Standards Track                     [Page 9]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


    DESCRIPTION
        "This identifies the no ATM traffic
        descriptor type.  Parameters 1, 2, 3, 4,
        and 5 are not used.  This traffic descriptor
        type can be used for best effort traffic."
    ::= {atmTrafficDescriptorTypes 1}

atmNoClpNoScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for no CLP
        and no Sustained Cell Rate.  The use of the
        parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: not used
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994."
    ::= {atmTrafficDescriptorTypes 2}

atmClpNoTaggingNoScr  OBJECT-IDENTITY
    STATUS  deprecated
    DESCRIPTION
        "This traffic descriptor is for CLP without
        tagging and no Sustained Cell Rate.  The use
        of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: peak cell rate in cells/second
                     for CLP=0 traffic
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used."
    ::= {atmTrafficDescriptorTypes 3}

atmClpTaggingNoScr  OBJECT-IDENTITY
    STATUS  deprecated
    DESCRIPTION
        "This traffic descriptor is for CLP with
        tagging and no Sustained Cell Rate.  The use
        of the parameter vector for this type:



Noto, et. al.               Standards Track                    [Page 10]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: peak cell rate in cells/second
                     for CLP=0 traffic, excess
                     tagged as CLP=1
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used."
    ::= {atmTrafficDescriptorTypes 4}

atmNoClpScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for no CLP
        with Sustained Cell Rate.  The use of the
        parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 3: maximum burst size in cells
        Parameter 4: not used
        Parameter 5: not used."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994."
    ::= {atmTrafficDescriptorTypes 5}

atmClpNoTaggingScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for CLP with
        Sustained Cell Rate and no tagging.  The use
        of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0 traffic
        Parameter 3: maximum burst size in cells
        Parameter 4: not used
        Parameter 5: not used."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,



Noto, et. al.               Standards Track                    [Page 11]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


           Version 3.1 (UNI 3.1) Specification,
           November 1994."
    ::= {atmTrafficDescriptorTypes 6}

atmClpTaggingScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for CLP with
        tagging and Sustained Cell Rate.  The use of
        the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0 traffic, excess tagged as
                     CLP=1
        Parameter 3: maximum burst size in cells
        Parameter 4: not used
        Parameter 5: not used."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994."
    ::= {atmTrafficDescriptorTypes 7}

atmClpNoTaggingMcr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for CLP with
        Minimum Cell Rate and no tagging.  The use of
        the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: CDVT in tenths of microseconds
        Parameter 3: minimum cell rate in cells/second
        Parameter 4: unused
        Parameter 5: unused."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994."
    ::= {atmTrafficDescriptorTypes 8}

atmClpTransparentNoScr  OBJECT-IDENTITY
    STATUS  current



Noto, et. al.               Standards Track                    [Page 12]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


    DESCRIPTION
        "This traffic descriptor type is for the CLP-
        transparent model and no Sustained Cell Rate.
        The use of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: CDVT in tenths of microseconds
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        connections following the CBR.1 conformance
        definition.

        Connections specifying this traffic descriptor
        type will be rejected at UNI 3.0 or UNI 3.1
        interfaces.  For a similar traffic descriptor
        type that can be accepted at UNI 3.0 and
        UNI 3.1 interfaces, see atmNoClpNoScr."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 9}

atmClpTransparentScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for the CLP-
        transparent model with Sustained Cell Rate.
        The use of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 3: maximum burst size in cells
        Parameter 4: CDVT in tenths of microseconds
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        connections following the VBR.1 conformance
        definition.




Noto, et. al.               Standards Track                    [Page 13]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        Connections specifying this traffic descriptor
        type will be rejected at UNI 3.0 or UNI 3.1
        interfaces.  For a similar traffic descriptor
        type that can be accepted at UNI 3.0 and
        UNI 3.1 interfaces, see atmNoClpScr."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 10}

atmNoClpTaggingNoScr  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for no CLP
        with tagging and no Sustained Cell Rate.  The
        use of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: CDVT in tenths of microseconds
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        connections following the UBR.2 conformance
        definition ."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 11}

atmNoClpNoScrCdvt  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for no CLP
        and no Sustained Cell Rate.  The use of the
        parameter vector for this type:
        Parameter 1: peak cell rate in cells/second



Noto, et. al.               Standards Track                    [Page 14]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


                     for CLP=0+1 traffic
        Parameter 2: CDVT in tenths of microseconds
        Parameter 3: not used
        Parameter 4: not used
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        CBR connections following the UNI 3.0/3.1
        conformance definition for PCR CLP=0+1.
        These CBR connections differ from CBR.1
        connections in that the CLR objective
        applies only to the CLP=0 cell flow.

        This traffic descriptor type is also
        applicable to connections following the UBR.1
        conformance definition."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 12}

atmNoClpScrCdvt  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for no CLP
        with Sustained Cell Rate.  The use of the
        parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 3: maximum burst size in cells
        Parameter 4: CDVT in tenths of microseconds
        Parameter 5: not used.

        This traffic descriptor type is applicable
        to VBR connections following the UNI 3.0/3.1
        conformance definition for PCR CLP=0+1 and
        SCR CLP=0+1.  These VBR connections
        differ from VBR.1 connections in that
        the CLR objective applies only to the CLP=0
        cell flow."
    REFERENCE



Noto, et. al.               Standards Track                    [Page 15]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 13}

atmClpNoTaggingScrCdvt  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for CLP with
        Sustained Cell Rate and no tagging.  The use
        of the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0 traffic
        Parameter 3: maximum burst size in cells
        Parameter 4: CDVT in tenths of microseconds
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        connections following the VBR.2 conformance
        definition."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 14}

atmClpTaggingScrCdvt  OBJECT-IDENTITY
    STATUS  current
    DESCRIPTION
        "This traffic descriptor type is for CLP with
        tagging and Sustained Cell Rate.  The use of
        the parameter vector for this type:
        Parameter 1: peak cell rate in cells/second
                     for CLP=0+1 traffic
        Parameter 2: sustainable cell rate in cells/second
                     for CLP=0 traffic, excess tagged as
                     CLP=1
        Parameter 3: maximum burst size in cells



Noto, et. al.               Standards Track                    [Page 16]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


        Parameter 4: CDVT in tenths of microseconds
        Parameter 5: not used.

        This traffic descriptor type is applicable to
        connections following the VBR.3 conformance
        definition."
    REFERENCE
        "ATM Forum,ATM User-Network Interface,
           Version 3.0 (UNI 3.0) Specification, 1994.
         ATM Forum, ATM User-Network Interface,
           Version 3.1 (UNI 3.1) Specification,
           November 1994.
         ATM Forum, Traffic Management Specification,
           Version 4.0, af-tm-0056.000, June 1996."
    ::= {atmTrafficDescriptorTypes 15}

END

3.  Acknowledgments

   This document is a product of the AToMMIB Working Group.

4.  References

   [1]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
        "Textual Conventions for Version 2 of the Simple Network
        Management Protocol (SNMPv2)", RFC 1903, January 1996.

   [2]  Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Structure
        of Management Information for Version 2 of the Simple Network
        Management Protocol (SNMPv2)", RFC 1902, January 1996.

   [3]  Tesink, K., Editor, "Definitions of Managed Objects for ATM
        Management", RFC 2515, February 1999.

5.  Security Considerations

   This memo defines textual conventions and object identities for use
   in ATM MIB modules. Security issues for these MIB modules are
   addressed in the memos defining those modules.











Noto, et. al.               Standards Track                    [Page 17]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


6.  Authors' Addresses

   Michael Noto
   3Com Corporation
   5400 Bayfront Plaza, M/S 3109
   Santa Clara, CA 95052

   Phone +1 408 326 2218
   Email: mike_noto@3com.com



   Ethan Mickey Spiegel
   Cisco Systems
   170 W. Tasman Dr.
   San Jose, CA 95134
   USA

   Phone +1 408 526 6408
   EMail: mspiegel@cisco.com


   Kaj Tesink
   Bellcore
   331 Newman Springs Road
   P.O. Box 7020
   Red Bank, NJ  07701-7020

   Phone: (732) 758-5254
   EMail: kaj@bellcore.com





















Noto, et. al.               Standards Track                    [Page 18]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


7.  Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.






























Noto, et. al.               Standards Track                    [Page 19]

RFC 2514             ATM TCs and OBJECT-IDENTITIES         February 1999


8.  Full Copyright Statement

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
























Noto, et. al.               Standards Track                    [Page 20]



ERRATA