rfc4764
Network Working Group F. Bersani
Request for Comments: 4764 France Telecom R&D
Category: Experimental H. Tschofenig
Siemens Networks GmbH & Co KG
January 2007
The EAP-PSK Protocol:
A Pre-Shared Key Extensible Authentication Protocol (EAP) Method
Status of This Memo
This memo defines an Experimental Protocol for the Internet
community. It does not specify an Internet standard of any kind.
Discussion and suggestions for improvement are requested.
Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
IESG Note
This RFC is not a candidate for any level of Internet Standard. The
IETF disclaims any knowledge of the fitness of this RFC for any
purpose and in particular notes that the decision to publish is not
based on IETF review for such things as security, congestion control,
or inappropriate interaction with deployed protocols. The RFC Editor
has chosen to publish this document at its discretion. Readers of
this document should exercise caution in evaluating its value for
implementation and deployment. See RFC 3932 for more information.
The IESG thinks that this work is related to IETF work done in WGs
EMU and EAP, but this does not prevent publishing.
Abstract
This document specifies EAP-PSK, an Extensible Authentication
Protocol (EAP) method for mutual authentication and session key
derivation using a Pre-Shared Key (PSK). EAP-PSK provides a
protected communication channel when mutual authentication is
successful for both parties to communicate over. This document
describes the use of this channel only for protected exchange of
result indications, but future EAP-PSK extensions may use the channel
for other purposes. EAP-PSK is designed for authentication over
insecure networks such as IEEE 802.11.
Bersani & Tschofenig Experimental [Page 1]
RFC 4764 EAP-PSK January 2007
Table of Contents
1. Introduction ....................................................4
1.1. Design Goals for EAP-PSK ...................................4
1.1.1. Simplicity ..........................................4
1.1.2. Wide Applicability ..................................5
1.1.3. Security ............................................5
1.1.4. Extensibility .......................................5
1.2. Terminology ................................................5
1.3. Conventions ................................................8
1.4. Related Work ...............................................9
2. Protocol Overview ..............................................12
2.1. EAP-PSK Key Hierarchy .....................................13
2.1.1. The PSK ............................................13
2.1.2. AK .................................................14
2.1.3. KDK ................................................14
2.2. The TEK ...................................................15
2.3. The MSK ...................................................15
2.4. The EMSK ..................................................15
2.5. The IV ....................................................15
3. Cryptographic Design of EAP-PSK ................................15
3.1. The Key Setup .............................................16
3.2. The Authenticated Key Exchange ............................19
3.3. The Protected Channel .....................................23
4. EAP-PSK Message Flows ..........................................25
4.1. EAP-PSK Standard Authentication ...........................26
4.2. EAP-PSK Extended Authentication ...........................28
5. EAP-PSK Message Format .........................................31
5.1. EAP-PSK First Message .....................................32
5.2. EAP-PSK Second Message ....................................34
5.3. EAP-PSK Third Message .....................................36
5.4. EAP-PSK Fourth Message ....................................39
6. Rules of Operation for the EAP-PSK Protected Channel ...........41
6.1. Protected Result Indications ..............................41
6.1.1. CONT ...............................................42
6.1.2. DONE_SUCCESS .......................................43
6.1.3. DONE_FAILURE .......................................43
6.2. Extended Authentication ...................................43
7. IANA Considerations ............................................45
7.1. Allocation of an EAP-Request/Response Type for EAP-PSK ....45
7.2. Allocation of EXT Type Numbers ............................45
8. Security Considerations ........................................46
8.1. Mutual Authentication .....................................46
8.2. Protected Result Indications ..............................47
8.3. Integrity Protection ......................................48
8.4. Replay Protection .........................................48
8.5. Reflection Attacks ........................................48
8.6. Dictionary Attacks ........................................49
Bersani & Tschofenig Experimental [Page 2]
RFC 4764 EAP-PSK January 2007
8.7. Key Derivation ............................................49
8.8. Denial-of-Service Resistance ..............................51
8.9. Session Independence ......................................51
8.10. Exposition of the PSK ....................................52
8.11. Fragmentation ............................................52
8.12. Channel Binding ..........................................53
8.13. Fast Reconnect ...........................................53
8.14. Identity Protection ......................................53
8.15. Protected Ciphersuite Negotiation ........................55
8.16. Confidentiality ..........................................55
8.17. Cryptographic Binding ....................................55
8.18. Implementation of EAP-PSK ................................55
9. Security Claims ................................................56
10. Acknowledgments ...............................................57
11. References ....................................................57
11.1. Normative References .....................................57
11.2. Informative References ...................................58
Appendix A. Generation of the PSK from a Password - Discouraged ...62
Bersani & Tschofenig Experimental [Page 3]
RFC 4764 EAP-PSK January 2007
1. Introduction
1.1. Design Goals for EAP-PSK
The Extensible Authentication Protocol (EAP) [3] provides an
authentication framework that supports multiple authentication
methods.
This document specifies an EAP method, called EAP-PSK, that uses a
Pre-Shared Key (PSK).
EAP-PSK was developed at France Telecom R&D in 2003-2004. It is
published as an RFC for the general information of the Internet
community and to allow independent implementations.
Because PSKs are of frequent use in security protocols, other
protocols may also refer to a PSK or contain this word in their name.
For instance, Wi-Fi Protected Access (WPA) [48] specifies an
authentication mode called "WPA-PSK". EAP-PSK is distinct from these
protocols and should not be confused with them.
Design goals for EAP-PSK were:
o Simplicity: EAP-PSK should be easy to implement and deploy without
any pre-existing infrastructure. It should be available quickly
because recently-released protocols, such as IEEE 802.11i [27],
employ EAP in a different threat model than PPP [44] and thus
require "modern" EAP methods.
o Wide applicability: EAP-PSK should be suitable to authenticate
over any network, and in particular over IEEE 802.11 [28] wireless
LANs.
o Security: EAP-PSK should be conservative in its cryptographic
design.
o Extensibility: EAP-PSK should be easily extensible.
1.1.1. Simplicity
For the sake of simplicity, EAP-PSK relies on a single cryptographic
primitive, AES-128 [7].
Restriction to such a primitive, and in particular, not using
asymmetric cryptography like Diffie-Hellman key exchange, makes EAP-
PSK:
Bersani & Tschofenig Experimental [Page 4]
RFC 4764 EAP-PSK January 2007
o Easy to understand and implement while avoiding cryptographic
negotiations.
o Lightweight and well suited for any type of device, especially
those with little processing power and memory.
However, as further discussed in Section 8, this prevents EAP-PSK
from offering advanced features such as identity protection, password
support, or Perfect Forward Secrecy (PFS). This choice has been
deliberately made as a trade-off between simplicity and security.
For the sake of simplicity, EAP-PSK has also chosen a fixed message
format and not a Type-Length-Value (TLV) design.
1.1.2. Wide Applicability
EAP-PSK has been designed in a threat model where the attacker has
full control over the communication channel. This is the EAP threat
model that is presented in Section 7.1 of [3].
1.1.3. Security
Since the design of authenticated key exchange is notoriously known
to be hard and error prone, EAP-PSK tries to avoid inventing any new
cryptographic mechanism. It attempts instead to build on existing
primitives and protocols that have been reviewed by the cryptographic
community.
1.1.4. Extensibility
EAP-PSK explicitly provides a mechanism to allow future extensions
within its protected channel (see Section 3.3). Thanks to this
mechanism, EAP-PSK will be able to provide more sophisticated
services as the need to do so arises.
1.2. Terminology
Authentication, Authorization, and Accounting (AAA)
Please refer to [10] for more details.
AES-128 A block cipher specified in the Advanced Encryption
Standard [7].
Authentication Key (AK)
A 16-byte key derived from the PSK that the EAP peer and
server use to mutually authenticate.
Bersani & Tschofenig Experimental [Page 5]
RFC 4764 EAP-PSK January 2007
AKEP2 An authenticated key exchange protocol; please refer to
[14] for more details.
Backend Authentication Server
An entity that provides an authentication service to an
Authenticator. When used, this server typically executes
EAP methods for the Authenticator. (This terminology is
also used in [26], and has the same meaning in this
document.)
CMAC Cipher-based Message Authentication Code. It is the
authentication mode of operation of AES recommended by NIST
in [8].
Extensible Authentication Protocol (EAP)
Defined in [3].
EAP Authenticator (or simply Authenticator)
The end of the EAP link initiating the EAP authentication
methods. (This terminology is also used in [26], and has
the same meaning in this document.)
EAP peer (or simply peer)
The end of the EAP link that responds to the Authenticator.
(In [26], this end is known as the Supplicant.)
EAP server (or simply server)
The entity that terminates the EAP authentication with the
peer. When there is no Backend Authentication Server, this
term refers to the EAP Authenticator. Where the EAP
Authenticator operates in pass-through mode, it refers to
the Backend Authentication Server.
EAX An authenticated-encryption with associated data mode of
operation for block ciphers [4].
Extended Master Session Key (EMSK)
Additional keying material derived between the EAP peer and
server that is exported by the EAP method. The EMSK is
reserved for future uses that are not defined yet and is
not provided to a third party. Please refer to [9] for
more details.
EAP-PSK generates a 64-byte EMSK.
Initialization Vector (IV)
A quantity of at least 64 bytes, suitable for use in an
initialization vector field, that is derived between the
peer and EAP server. Since the IV is a known value in
Bersani & Tschofenig Experimental [Page 6]
RFC 4764 EAP-PSK January 2007
methods such as EAP-TLS [11], it cannot be used by itself
for computation of any quantity that needs to remain
secret. As a result, its use has been deprecated and EAP
methods are not required to generate it. Please refer to
[9] for more details.
EAP-PSK does not generate an IV.
Key-Derivation Key (KDK)
A 16-byte key derived from the PSK that the EAP peer and
server use to derive session keys (namely, the TEK, MSK,
and EMSK).
Message Authentication Code (MAC)
Informally, the purpose of a MAC is to provide assurances
regarding both the source of a message and its integrity
[40]. IEEE 802.11i uses the acronym MIC (Message Integrity
Check) to avoid confusion with the other meaning of the
acronym MAC (Medium Access Control).
Master Session Key (MSK)
Keying material that is derived between the EAP peer and
server and exported by the EAP method. In existing
implementations, a AAA server acting as an EAP server
transports the MSK to the Authenticator [9].
EAP-PSK generates a 64-byte MSK.
Network Access Identifier (NAI)
Identifier used to identify the communicating parties [2].
One Key CBC-MAC 1 (OMAC1)
A method to generate a Message Authentication Code [29].
CMAC is the name under which NIST has standardized OMAC1.
Perfect Forward Secrecy (PFS)
The confidence that the compromise of a long-term private
key does not compromise any earlier session keys. In other
words, once an EAP dialog is finished and its corresponding
keys are forgotten, even someone who has recorded all of
the data from the connection and gets access to all of the
long-term keys of the peer and the server cannot
reconstruct the keys used to protect the conversation
without doing a brute-force search of the session key
space.
EAP-PSK does not have this property.
Bersani & Tschofenig Experimental [Page 7]
RFC 4764 EAP-PSK January 2007
Pre-Shared Key (PSK)
A Pre-Shared Key simply means a key in symmetric
cryptography. This key is derived by some prior mechanism
and shared between the parties before the protocol using it
takes place. It is merely a bit sequence of given length,
each bit of which has been chosen at random uniformly and
independently. For EAP-PSK, the PSK is the long-term 16-
byte credential shared by the EAP peer and server.
Protected Result Indication
Please refer to Section 7.16 of [3] for a definition of
this term. This feature has been introduced because EAP-
Success/Failure packets are unidirectional and are not
protected.
Transient EAP Key (TEK)
A session key that is used to establish a protected channel
between the EAP peer and server during the EAP
authentication exchange. The TEK is appropriate for use
with the ciphersuite negotiated between the EAP peer and
server to protect the EAP conversation. Note that the
ciphersuite used to set up the protected channel between
the EAP peer and server during EAP authentication is
unrelated to the ciphersuite used to subsequently protect
data sent between the EAP peer and Authenticator [9].
EAP-PSK uses a 16-byte TEK for its protected channel, which
is the only ciphersuite available between the EAP peer and
server to protect the EAP conversation. This ciphersuite
uses AES-128 in the EAX mode of operation.
1.3. Conventions
All numbers presented in this document are considered in network-byte
order.
|| denotes concatenation of strings (and not the logical OR).
MAC(K, String) denotes the MAC of String under the key K (the
algorithm used in this document to compute the MACs is CMAC with AES-
128; see Section 3.2).
[String] denotes the concatenation of String with the MAC of String
calculated as specified by the context. Hence, we have, with K
specified by the context: [String]=String||MAC(K,String)
** denotes integer exponentiation.
Bersani & Tschofenig Experimental [Page 8]
RFC 4764 EAP-PSK January 2007
"i" denotes the unsigned binary representation on 16 bytes of the
integer i in network byte order. Therefore, this notation only makes
sense when i is between 0 and 2**128-1.
<i> denotes the unsigned binary representation on 4 bytes of the
integer i in network byte order. Therefore, this notation only makes
sense when i is between 0 and 2**32-1.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [1].
1.4. Related Work
At the time this document is written, only three EAP methods are
standards track EAP methods per IETF terminology (see [17]), namely:
o MD5-Challenge (EAP-Request/Response type 4), defined in [3], which
uses a MD5 challenge similar to [45].
o OTP (EAP-Request/Response type 5), defined in [3], which aims at
providing One-Time Password support similar to [22] and [39].
o GTC (EAP-Request/Response type 6), defined in [3], which aims at
providing Generic Token Card Support.
Unfortunately, all three methods are deprecated for security reasons
that are explained in part in [3].
Myriads of EAP methods have, however, been otherwise proposed:
o One as an experimental RFC (EAP-TLS [11]), which therefore is not
a standard (see [25]).
o Some as individual Internet-Draft submissions (e.g., [42] or this
document).
o And some even undocumented (e.g., Rob EAP, which has EAP-Request/
Response type 31).
However, no secure and mature Pre-Shared Key EAP method is yet easily
and widely available, which is all the more regrettable because Pre-
Shared Key methods are the most basic ones!
The existing proposals for a future Pre-Shared Key EAP method are
briefly reviewed hereafter (please refer to [16] for a more thorough
synthesis of EAP methods).
Bersani & Tschofenig Experimental [Page 9]
RFC 4764 EAP-PSK January 2007
Among these proposals, there are some that:
o Are broken from a security point of view, e.g.:
* LEAP, which is specified in [38] and whose vulnerabilities are
discussed in [49].
* EAP-MSCHAPv2, which is specified in [34] and whose
vulnerabilities are indirectly discussed in [43].
o Essentially require additional infrastructure, e.g., EAP-SIM [24],
EAP-AKA [12], or OTP/token card methods like [31].
o Are not shared key methods but are often confused with them,
namely, the password methods, e.g., EAP-SRP [18] or SPEKE [30],
whose wide adoption very unfortunately seems to be hindered by
Intellectual Property Rights issues.
o Are generic tunneling methods, which do not essentially rely on
Pre-Shared Keys as they require a public-key certificate for the
server and allow the peer to authenticate with whatever EAP method
or even other non-EAP authentication mechanisms, namely, [32] and
[21].
o Are abandoned but have provided the basis for EAP-PSK, namely,
EAP-Archie [47].
o Are possible alternatives to EAP-PSK (i.e., claimed to be secure
and subject of active work):
* EAP-FAST [42].
* EAP-IKEv2 [46].
* EAP-TLS (when shared key/password support is added to TLS; see
[50]).
EAP-PSK differs from the aforementioned methods on the following
points:
o No attacks on EAP-PSK within its threat model have yet been found.
o EAP-PSK was not designed to leverage a pre-existing
infrastructure. Thus, it does not inherit potential limitations
of such an infrastructure and it should be easier to deploy "from
scratch".
o EAP-PSK wished to avoid IPR blockages.
Bersani & Tschofenig Experimental [Page 10]
RFC 4764 EAP-PSK January 2007
o EAP-PSK does not have any dependencies on protocols other than
EAP.
o EAP-PSK was restricted to simply proposing a Pre-Shared Key method
with symmetric cryptography
* To remain simple to understand and implement
* To avoid potentially complex configurations and negotiations
o EAP-PSK was designed with efficiency in mind.
Bersani & Tschofenig Experimental [Page 11]
RFC 4764 EAP-PSK January 2007
2. Protocol Overview
Figure 1 presents an overview of the EAP-PSK key hierarchy.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++ ---+
| | ^
| EAP-PSK Protocol: a Pre-Shared Key EAP Method | |
| | |
| +----------+ | |
| | PSK | | |
| |(16 bytes)| | |
| +----------+ | |
| | | |
| v | |
| *********************** | |
| *Modified Counter Mode* | |
| *********************** | |
| | | | |
| v v | |
| +----------+ +----------+ +----------------+ | |
| | AK | | KDK | | RAND_P | | |
| |(16 bytes)| |(16 bytes)| | (16 bytes) | | |
| +----------+ +----------+ +----------------+ | |
| | | | |
| | | | |
| +-----------+ | | | |
| +--------+|Plain Text | | | | |
|+-------+|Header H||Var.Length | | | | |
||Nonce N||22 bytes|+-----------+ v v Local |
||4 bytes|+--------+ | *********************** to EAP |
|+-------+ | +--------+ +------*Modified Counter Mode* Method |
| | v v v *********************** | |
| | ******* +--------+ |64 |64 | |
| | * EAX *-------|TEK | |bytes |bytes | |
| +-->******* |16 bytes| | | | |
| | +--------+ | | | |
| +-----+----+ | | | |
| v v | | | |
|+--------+ +-------------------+ | | | |
||Tag | |Cipher Text Payload| | | | |
||16 bytes| | Variable length L | | | | |
|+--------+ +-------------------+ | | | V
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-++ ---+
| | ^
+-+-+-+-+-++ +-+-+-+-+-++ |
|MSK | |EMSK | |
| | | | Exported |
+-+-+-+-+-++ +-+-+-+-+-++ by EAP |
Bersani & Tschofenig Experimental [Page 12]
RFC 4764 EAP-PSK January 2007
| | Method |
| | |
V V |
************************* V
* AAA Key Derivation * ---+
* Naming & Binding *
*************************
Figure 1: EAP-PSK Key Hierarchy Overview
2.1. EAP-PSK Key Hierarchy
This section presents the key hierarchy used by EAP-PSK. This
hierarchy is inspired by the EAP key hierarchy described in [9].
2.1.1. The PSK
The PSK is shared between the EAP peer and the EAP server.
EAP-PSK assumes that the PSK is known only to the EAP peer and EAP
server. The security properties of the protocol are compromised if
it has wider distribution. Please note that EAP-PSK shares this
property with all other symmetric key methods (including all
password-based methods).
EAP-PSK also assumes the EAP server and EAP peer identify the correct
PSK to use with each other thanks to their respective NAIs. This
means that there MUST only be at most one PSK shared between an EAP
server using a given server NAI and an EAP peer using a given peer
NAI.
This PSK is used, as shown in Figure 2, to derive two 16-byte static
long-lived subkeys, respectively called the Authentication Key (AK)
and the Key-Derivation Key (KDK). This derivation should only be
done once: it is called the key setup. See Section 3.1 for an
explanation of why PSK is not used as a static long-lived key, but
only as the initial keying material for deriving the static long-
lived keys, AK and KDK, which are actually used by the protocol EAP-
PSK.
Bersani & Tschofenig Experimental [Page 13]
RFC 4764 EAP-PSK January 2007
+---------------------------+
| PSK |
| (16 bytes) |
+---------------------------+
| |
v v
+---------------------------+ +---------------------------+
| AK | | KDK |
| (16 bytes) | | (16 bytes) |
+---------------------------+ +---------------------------+
Figure 2: Derivation of AK and KDK from the PSK
2.1.2. AK
EAP-PSK uses AK to mutually authenticate the EAP peer and the EAP
server.
AK is a static long-lived key derived from the PSK; see Section 3.1.
AK is not a session key.
The EAP server and EAP peer identify the correct AK to use with each
other thanks to their respective NAIs. This means that there MUST
only be at most one AK shared between an EAP server using a given
server NAI and an EAP peer using a given peer NAI. This is the case
when there is at most one PSK shared between an EAP server using a
given server NAI and an EAP peer using a given peer NAI; see
Section 2.1.1.
The EAP peer chooses the AK to use based on the EAP server NAI that
has been sent by the EAP server in the first EAP-PSK message (namely,
ID_S; see Section 4.1) and the EAP peer NAI it chooses to include in
the second EAP-PSK message (namely, ID_P; see Section 4.1).
2.1.3. KDK
EAP-PSK uses KDK to derive session keys shared by the EAP peer and
the EAP server (namely, the TEK, MSK, and EMSK).
KDK is a static long-lived key derived from the PSK; see Section 3.1.
KDK is not a session key.
The EAP server and EAP peer identify the correct AK to use with each
other thanks to their respective NAIs. This means that there MUST
only be at most one AK shared between an EAP server using a given
server NAI and an EAP peer using a given peer NAI. This is the case
Bersani & Tschofenig Experimental [Page 14]
RFC 4764 EAP-PSK January 2007
when there is at most one PSK shared between an EAP server using a
given server NAI and an EAP peer using a given peer NAI; see
Section 2.1.1.
The EAP peer chooses the AK to use based on the EAP server NAI that
has been sent by the EAP server in the first EAP-PSK message (namely,
ID_S; see Section 4.1) and the EAP peer NAI it chooses to include in
the second EAP-PSK message (namely, ID_P; see Section 4.1).
2.2. The TEK
EAP-PSK derives a 16-byte TEK thanks to a random number exchanged
during authentication (RAND_P; see Section 5.1) and KDK.
This TEK is used to implement a protected channel for both mutually
authenticated parties to communicate over securely.
2.3. The MSK
EAP-PSK derives a MSK thanks to a random number exchanged during
authentication (RAND_P; see Section 5.1) and the KDK.
The MSK is 64 bytes long, which complies with [3].
2.4. The EMSK
EAP-PSK derives an EMSK thanks to a random number exchanged during
authentication (RAND_P; see Section 5.1) and the KDK.
The EMSK is 64 bytes long, which complies with [3].
2.5. The IV
EAP-PSK does not derive any IV, which complies with [9].
3. Cryptographic Design of EAP-PSK
EAP-PSK relies on a single cryptographic primitive, a block cipher,
which is instantiated with AES-128. AES-128 takes a 16-byte Pre-
Shared Key and a 16-byte Plain Text block as inputs. It outputs a
16-byte Cipher Text block. For a detailed description of AES-128,
please refer to [7].
AES-128 has been chosen because:
o It is standardized and implementations are widely available.
Bersani & Tschofenig Experimental [Page 15]
RFC 4764 EAP-PSK January 2007
o It has been carefully reviewed by the cryptographic community and
is believed to be secure.
Other block ciphers could easily be proposed for EAP-PSK, as EAP-PSK
does not intrinsically depend on AES-128. The only parameters of
AES-128 that EAP-PSK depends on are the AES-128 block and key size
(16 bytes). For the sake of simplicity, EAP-PSK has, however, been
chosen to restrict to a single mandatory block cipher and not allow
the negotiation of other block ciphers. In the case that AES-128 is
deprecated for security reasons, EAP-PSK should also be deprecated
and a cut-and-paste EAP-PSK' should be defined with another block
cipher. This EAP-PSK' should not be backward compatible with EAP-PSK
because of the security issues with AES-128. EAP-PSK' should
therefore use a different EAP-Request/Response Type number. With the
EAP-Request/Response Type number space structure defined in [3], this
should not be a problem. The use of a different EAP-Request/Response
Type number for EAP-PSK' will prevent this new method from being
vulnerable to chosen protocol attacks.
EAP-PSK uses three cryptographic parts:
o A key setup to derive AK and KDK from the PSK.
o An authenticated key exchange protocol to mutually authenticate
the communicating parties and derive session keys.
o A protected channel protocol for both mutually authenticated
parties to communicate over.
Each part is discussed in more detail in the subsequent paragraphs.
3.1. The Key Setup
EAP-PSK needs two cryptographically separated 16-byte subkeys for
mutual authentication and session key derivation. Indeed, it is a
rule of thumb in cryptography to use different keys for different
applications.
It could have implemented these two subkeys either by specifying a
32-byte PSK that would then be split in two 16-byte subkeys, or by
specifying a 16-byte PSK that would then be cryptographically
expanded to two 16-byte subkeys.
Because provisioning a 32-byte long-term credential is more
cumbersome than a 16-byte one, and the strength of the derived
session keys is 16 bytes either way, the latter option was chosen.
Bersani & Tschofenig Experimental [Page 16]
RFC 4764 EAP-PSK January 2007
Hence, the PSK is only used by EAP-PSK to derive AK and KDK. This
derivation should be done only once, immediately after the PSK has
been provisioned. As soon as AK and KDK have been derived, the PSK
should be deleted. If the PSK is deleted, it should be done so
securely (see, for instance, [19] for guidance on secure deletion of
the PSK).
Derivation of AK and KDK from the PSK is called the key setup:
o The input to the key setup is the PSK.
o The outputs of the key setup are AK and KDK.
AK and KDK are derived from the PSK using the modified counter mode
of operation of AES-128. The modified counter mode is a length
increasing function, i.e., it expands one AES-128 input block into a
longer t-block output, where t>=2. This mode was chosen for the key
setup because it had already been chosen for the derivation of the
session keys (see Section 3.2).
The details of the derivation of AK and KDK from the PSK are shown in
Figure 3.
Bersani & Tschofenig Experimental [Page 17]
RFC 4764 EAP-PSK January 2007
+--------------------------+
| "0" |
| Input Block (16 bytes) |
+--------------------------+
|
v
+----------------+
| |
| AES-128(PSK,.) |
| |
+----------------+
|
|
+----------------------------+
| |
v v
+--------+ +---+ +--------+ +---+
| c1="1" |->|XOR| | c2="2" |->|XOR|
|16 bytes| +---+ |16 bytes| +---+
+--------+ | +--------+ |
| |
+----------------+ +----------------+
| | | |
| AES-128(PSK,.) | | AES-128(PSK,.) |
| | | |
+----------------+ +----------------+
| |
| |
v v
+------------------------+ +------------------------+
| AK | | KDK |
| (16 bytes) | | (16 bytes) |
+------------------------+ +------------------------+
Figure 3: Derivation of AK and KDK from the PSK in Details
The input block is "0". For the sake of simplicity, this input block
has been chosen constant: it could have been set to a value depending
on the peer and the server (for instance, the XOR of their respective
NAIs appropriately truncated or zero-padded), but this did not seem
to add much security to the scheme, whereas it added complexity. Any
16-byte constant could have been chosen, as the security is not
supposed to depend on the particular value taken by the constant. "0"
was arbitrarily chosen.
Bersani & Tschofenig Experimental [Page 18]
RFC 4764 EAP-PSK January 2007
3.2. The Authenticated Key Exchange
The authentication protocol used by EAP-PSK is inspired by AKEP2,
which is described in [14].
AKEP2 consists of a one-and-a-half round-trip exchange, as shown in
Figure 4, which is inspired by Figure 5 of [14].
Bob Alice
| RA |
|<---------------------------------------------------------|
| |
| [B||A||RA||RB] |
|--------------------------------------------------------->|
| |
| [A||RB] |
|<---------------------------------------------------------|
Figure 4: Overview of AKEP2
It is also worth noting that [14] focuses on cryptography and not on
designing a real-life protocol. Thus, as noted in subsection "Out-
Of-Band-Data" of [14], Alice has to send A, its identity, to Bob so
that Bob may select the appropriate credential for the sequel to the
conversation. This leads to a slightly complemented version of AKEP2
for EAP-PSK as depicted in Figure 5.
Bob Alice
| A||RA |
|<---------------------------------------------------------|
| |
| [B||A||RA||RB] |
|--------------------------------------------------------->|
| |
| [A||RB] |
|<---------------------------------------------------------|
Figure 5: Overview of AKEP2
In AKEP2,
o RA and RB are random numbers chosen respectively by Alice and Bob.
o A and B are Alice's and Bob's respective identities. They allow
Alice and Bob to retrieve the key that they have to use to run an
authenticated key exchange between each other. They are also
included in the protocol for cryptographic reasons.
Bersani & Tschofenig Experimental [Page 19]
RFC 4764 EAP-PSK January 2007
o The MACs (see Section 1.3 for the notation "[]") are calculated
using a dedicated key.
EAP-PSK instantiates this protocol with:
o The server as Alice and the peer as Bob.
o RA and RB as 16-byte random numbers, using Section 4.1 notations;
this means RA=RAND_S and RB=RAND_P.
o A and B as Alice's and Bob's respective NAIs, using Section 4.1
notations; this means A=ID_S and B=ID_P.
o The MAC algorithm as CMAC with AES-128 using AK and producing a
tag length of 16 bytes.
o The modified counter mode of operation of AES-128 using KDK, to
derive session keys as a result of this exchange.
CMAC was chosen as the MAC algorithm because it is capable of
handling arbitrary length messages, and its design is simple. It
also enjoys up-to-date review by the cryptographic community,
especially using provable security concepts. It has been recommended
by the NIST. For a detailed description of CMAC, please refer to
[8].
In AKEP2, the key exchange is "implicit": the session keys are
derived from RB. In EAP-PSK, the session keys are thus derived from
RAND_P by using KDK and the modified counter mode of operation of
AES-128 described in [5]. This mode was chosen because it is a
simple key derivation scheme that relies on a block cipher and has a
proof of its security. It is a length increasing function, i.e., it
expands one AES-128 input block into a longer t-block output, where
t>=2. The derivation of the session keys is shown in Figure 6.
Bersani & Tschofenig Experimental [Page 20]
RFC 4764 EAP-PSK January 2007
+--------------------------+ +-------------------------------+
| RAND_P | | KDK |
| Input Block (16 bytes) | | Key Derivation Key (16 bytes) |
+--------------------------+ +-------------------------------+
| |
v v
+-----------------------------------------------------------------+
| |
| Modified Counter Mode |
| |
+-----------------------------------------------------------------+
| | |
v v v
+------------+ +----------------------+ +----------------------+
| TEK | | MSK | | EMSK |
| (16 bytes) | | (64 bytes) | | (64 bytes) |
+------------+ +----------------------+ +----------------------+
Figure 6: Derivation of the Session Keys
The input to the derivation of the session keys is RAND_P.
The outputs of the derivation of the session keys are:
o The 16-byte TEK (the first output block).
o The 64-byte MSK (the concatenation of the second to fifth output
blocks).
o The 64-byte EMSK (the concatenation of the sixth to ninth output
blocks).
The details of the derivation of the session keys are shown in
Figure 7.
Bersani & Tschofenig Experimental [Page 21]
RFC 4764 EAP-PSK January 2007
+--------------------------+
| RAND_P |
| Input Block (16 bytes) |
+--------------------------+
|
v
+----------------+
| |
| AES-128(KDK,.) |
| |
+----------------+
|
|
+---------------------+-- - - - - - - - - - --+
| | |
v v v
+--------+ +---+ +--------+ +---+ +--------+ +---+
| c1="1" |->|XOR| | c2="2" |->|XOR|.......| c9="9" |->|XOR|
|16 bytes| +---+ |16 bytes| +---+ |16 bytes| +---+
+--------+ | +--------+ | +--------+ |
| | |
+----------------+ +----------------+ +----------------+
| | | | | |
| AES-128(KDK,.) | | AES-128(KDK,.) |......| AES-128(KDK,.) |
| | | | | |
+----------------+ +----------------+ +----------------+
| | |
| | |
v v v
+-----------------+ +-----------------+ +------------------+
| Output Block #1 | | Output Block #2 | | Output Block #9 |
| (16 bytes) | | (16 bytes) |.....| (16 bytes) |
| TEK | | MSK (block 1/4) | | EMSK (block 4/4) |
+-----------------+ +-----------------+ +------------------+
Figure 7: Derivation of the Session Keys in Details
The counter values are set respectively to the first t integers (that
is, ci="i", with i=1 to 9).
Keying material is sensitive information and should be handled
accordingly (see Section 8.10 for further discussion).
Bersani & Tschofenig Experimental [Page 22]
RFC 4764 EAP-PSK January 2007
3.3. The Protected Channel
EAP-PSK provides a protected channel for both parties to communicate
over, in case of a successful authentication. This protected channel
is currently used to exchange protected result indications and may be
used in the future to implement extensions.
EAP-PSK uses the EAX mode of operation to provide this protected
channel. For a detailed description of EAX, please refer to [4].
Figure 8 shows how EAX is used to implement EAP-PSK protected
channel.
+-----------+ +----------------+ +---------------------+ +----------+
| Nonce N | | Header H | | Plain Text Payload | | TEK |
| 4 bytes | | 22 bytes | | Variable length L | | 16 bytes |
+-----------+ +----------------+ +---------------------+ +----------+
| | | |
v v v v
+-------------------------------------------------------------------+
| |
| EAX |
| |
+-------------------------------------------------------------------+
| |
v v
+---------------------+ +----------+
| Cipher Text Payload | | Tag |
| Variable length L | | 16 bytes |
+---------------------+ +----------+
Figure 8: The Protected Channel
This protected channel:
o Provides replay protection.
o Encrypts and authenticates a Plain Text Payload that becomes an
Encrypted Payload. The Plain Text Payload must not exceed 960
bytes; see Sections 5.3, 5.4, and 8.11.
o Only authenticates a Header that is thus sent in clear.
EAX is instantiated with AES-128 as the underlying block cipher.
AES-128 is keyed with the TEK.
Bersani & Tschofenig Experimental [Page 23]
RFC 4764 EAP-PSK January 2007
The nonce N is used to provide cryptographic security to the
encryption and data origin authentication as well as protection
replay. Indeed, N is a 4-byte sequence number starting from <0> that
is monotonically incremented at each EAP-PSK message within one EAP-
PSK dialog, except retransmissions, of course.
N was taken to be 4 bytes to avoid 16-byte arithmetic. Since EAX
uses a 16-byte nonce, N is padded with 96 zero bits for its high-
order bits.
For cryptographic reasons, N is not allowed to wrap around. In the
unlikely, yet possible, event of the server sending an EAP-PSK
message with N set to <2**32-2>, it must not send any further message
on this protected channel, which would cause to reusing the value 0.
Either the conversation is finished after the server receives the
EAP-PSK answer from the peer with N set to <2**32-1> and the server
proceeds (typically by sending an EAP-Success or Failure), or the
conversation is not finished and must then be aborted (a new EAP-PSK
dialog may subsequently be started to try again to authenticate).
Thus, the maximum number of messages that can be exchanged over the
same protected channel is 2**32 (which should not be a limitation in
practice, as this is approximately equal to 4 billion).
The Header H consists of the first 22 bytes of the EAP Request or
Response packet (i.e., the EAP Code, Identifier, Length, and Type
fields followed by the EAP-PSK Flags and RAND_S fields). Although it
may appear unorthodox that an upper layer (EAP-PSK) protects some
information of the lower layer (EAP), this was chosen to comply with
EAP recommendation (see Section 7.5. of [3]) and seems to be existing
practice at IETF (see, for instance, [35]).
The Plain Text Payload is the payload that is to be encrypted and
integrity protected. The Cipher Text Payload is the result of the
encryption of the Plain Text.
The Tag is a MAC that protects both the Header and the Plain Text
Payload. The verification of the Tag must only be done after a
successful verification of the Nonce for replay protection. If the
verification of the Tag succeeds, then the Encrypted Payload is
decrypted to recover the Plain Text Payload. If the verification of
the Tag fails, then no decryption is performed and this MAC failure
should be logged. The tag length is chosen to be 16 bytes for EAX
within EAP-PSK. This length is considered appropriate by the
cryptographic community.
Bersani & Tschofenig Experimental [Page 24]
RFC 4764 EAP-PSK January 2007
EAX was mainly chosen because:
o It strongly relies on OMAC in its design and OMAC1, a variant of
OMAC, had already been chosen in EAP-PSK for the authentication
part (please remember that OMAC1 and CMAC are analogous).
o Its design is simple.
o It enjoys a security proof.
o It is free of any Intellectual Property Rights claims.
4. EAP-PSK Message Flows
EAP-PSK may consist of two different types of message flows:
o The "standard authentication", which is:
* Mandatory to implement.
* Fully specified in this document.
* The simpler type of message flow, which is expected to be used
most frequently.
o The "extended authentication", which is:
* Optional to implement (i.e., there are no mandatory
extensions).
* Partly specified in this document since it depends on
extensions and none are currently specified, let alone in this
document.
* The type of message flow that should be used when extensions of
EAP-PSK are needed by more sophisticated usage scenarios and
are available.
EAP-PSK introduces the concept of a session to facilitate its
analysis and provide a cleaner interface to other layers. A session
is a particular instance of an EAP-PSK dialog between two parties.
This session is identified by a session identifier.
In the first EAP-PSK message, the EAP server asserts its identity.
Given that the EAP-Request/Identity and EAP-Response/Identity may not
be assumed to have occurred prior to this sending and that the
response included in EAP-Response/Identity (if this EAP Identity
exchange takes place) may not contain the actual NAI the peer shall
Bersani & Tschofenig Experimental [Page 25]
RFC 4764 EAP-PSK January 2007
use with EAP-PSK, this means that an EAP server implementing EAP-PSK
must use the same EAP server NAI for all EAP-PSK dialogs with any EAP
peer implementing EAP-PSK.
4.1. EAP-PSK Standard Authentication
EAP-PSK standard authentication is comprised of four messages, i.e.,
two round-trips; see Figure 9.
peer server
| Flags||RAND_S||ID_S |
|<---------------------------------------------------------|
| |
| Flags||RAND_S||RAND_P||MAC_P||ID_P |
|--------------------------------------------------------->|
| |
| Flags||RAND_S||MAC_S||PCHANNEL_S_0 |
|<---------------------------------------------------------|
| |
| Flags||RAND_S||PCHANNEL_P_1 |
|--------------------------------------------------------->|
| |
Figure 9: EAP-PSK Standard Authentication
o The first message is sent by the server to the peer to:
* Send a 16-byte random challenge (RAND_S). RAND_S was called RA
in Section 3.2
* State its identity (ID_S). ID_S was denoted by A in
Section 3.2.
o The second message is sent by the peer to the server to:
* Send another 16-byte random challenge (RAND_P). RAND_P was
called RB in Section 3.2
* State its identity (ID_P). ID_P was denoted by B in
Section 3.2.
* Authenticate to the server by proving that it is able to
compute a particular MAC (MAC_P), which is a function of the
two challenges and AK:
MAC_P = CMAC-AES-128(AK, ID_P||ID_S||RAND_S||RAND_P)
Bersani & Tschofenig Experimental [Page 26]
RFC 4764 EAP-PSK January 2007
o The third message is sent by the server to the peer to:
* Authenticate to the peer by proving that it is able to compute
another MAC (MAC_S), which is a function of the peer's
challenge and AK:
MAC_S = CMAC-AES-128(AK, ID_S||RAND_P)
* Set up the protected channel (P_CHANNEL_S_0) to:
+ Confirm that it has derived session keys (at least the TEK).
+ Give a protected result indication of the authentication.
o The fourth message is sent by the peer to the server to finish the
setup of the protected channel (P_CHANNEL_P_1) to:
* Confirm that it has derived session keys (at least the TEK).
* Give a protected result indication of the authentication.
The PCHANNEL_S_0 and PCHANNEL_P_1 fields of the third and fourth EAP-
PSK messages contain a MAC-computed thanks to TEK that protects the
integrity of the messages. For a detailed list of the fields of the
messages that are integrity protected, please refer to Section 3.3.
All EAP-PSK messages include a sort of header, which is comprised of
two fields:
o Flags, a 1-byte field that is currently only used to number EAP-
PSK messages.
o RAND_S, a 16-byte challenge sent by the server that is used as a
session identifier.
This standard message flow could be comprised of only three messages,
like AKEP2, were it not the request/response nature of EAP that
prevents the third message to be the last one. Since the fourth
message is mandatory, EAP-PSK chose to take advantage of this and set
up a protected channel.
The standard message flow also includes a statement by the peer of
its identity, in addition to the EAP-Response/Identity it may have
sent. This behavior follows Section 5.1 of [3], which recommends
that the EAP-Response/Identity be used primarily for routing purposes
and selecting which EAP method to use, and therefore that EAP methods
include a method-specific mechanism for obtaining the identity, so
that they do not have to rely on the Identity Response.
Bersani & Tschofenig Experimental [Page 27]
RFC 4764 EAP-PSK January 2007
When a party receives an EAP-PSK message, it checks that the message
is syntactically valid in accordance with the message formats defined
in Section 5. If the message is syntactically incorrect, then it is
silently discarded. Then it checks the cryptographic validity of
this message, i.e., it checks the MAC(s) as follows:
o If the received message is the first EAP-PSK message, there is no
MAC to check as none is included in message 1.
o If the received message is the second EAP-PSK message, the
validity of MAC_P is checked.
o If the received message is the third EAP-PSK message, the validity
of MAC_S is checked and then the validity of the Tag included in
P_CHANNEL_S_0 is checked. The validity checks must be done in
this order to avoid unnecessarily deriving TEK, MSK, and EMSK in
case MAC_S is invalid, meaning that mutual authentication has
failed. Indeed, TEK is used to verify the validity of the Tag
included in P_CHANNEL_S_0.
o If the received message is the fourth EAP-PSK message, the
validity of the Tag included in P_CHANNEL_P_1 is checked.
If a validity check fails, the message is silently discarded. There
can be a counter to track the number of silently discarded messages
Section 8.8. If there is an encrypted payload in the message
(namely, in the PCHANNEL attribute), then the encrypted payload is
decrypted. Then, if the decrypted payload is syntactically
incorrect, the message is silently discarded.
4.2. EAP-PSK Extended Authentication
To remain simple and yet be extensible to meet future requirements,
EAP-PSK provides an extension mechanism within its protected channel:
the payload of the protected channel may contain an optional
extension field (EXT).
Figure 10 presents the message sequence for EAP-PSK extended
authentication.
Extended authentication MUST be supported, i.e., any EAP-PSK
implementation MUST support sending and reception of an EXT attribute
according to rules of operation described in Section 6. Yet,
although support of the EXT field is mandatory, there is no mandatory
extension type to support. This means that if a server engages in
EAP-PSK extended authentication, as only the server can start
extended authentication per Section 6, a peer will recognize the
attempt to start extended authentication through its EXT support. If
Bersani & Tschofenig Experimental [Page 28]
RFC 4764 EAP-PSK January 2007
the peer does not support the particular extension type used by the
server, the peer will still be able to conclude the EAP-PSK dialog.
The mandatory support of the EXT field is dictated:
o To guarantee a robust behavior in the future where some peers
might support some extensions and others not. All peers will thus
be able to understand that an extended authentication is being
attempted and indicate whether or not they support the extension
that is tried.
o To ensure that all implementations will indeed be extensible.
No extension is currently defined.
At most, one extension may be run within a single EAP-PSK dialog:
there can neither be sequences of extensions nor interleaved
extensions. However, extensions may take a variable number of round-
trips to complete.
Only the server can start an extension and, if it does so, it must
start it in the first payload it sends over the protected channel.
peer server
| Flags||RAND_S||ID_S |
|<---------------------------------------------------------|
| |
| Flags||RAND_S||RAND_P||MAC_P||ID_P |
|--------------------------------------------------------->|
| |
| Flags||RAND_S||MAC_S||PCHANNEL_S_0(EXT) |
|<---------------------------------------------------------|
| |
| Flags||RAND_S||PCHANNEL_P_1(EXT) |
|--------------------------------------------------------->|
| |
. .
. .
. .
| Flags||RAND_S||PCHANNEL_S_2i(EXT) |
|<---------------------------------------------------------|
| |
| Flags||RAND_S||PCHANNEL_P_2i+1(EXT) |
|--------------------------------------------------------->|
| |
Figure 10: EAP-PSK Extended Authentication
Bersani & Tschofenig Experimental [Page 29]
RFC 4764 EAP-PSK January 2007
Please refer to Section 6 for more details on how extended
authentication works.
The PCHANNEL_S_2j and PCHANNEL_P_2j+1 fields of the EAP-PSK messages
(where j varies from 0 to i) contain a MAC-computed thanks to TEK
that protects the integrity of the messages. For a detailed list of
the fields of the messages that are integrity protected, please refer
to Section 3.3.
When a party receives an EAP-PSK message, it checks that the message
is syntactically valid in accordance with the message formats defined
in Section 5. If the message is syntactically incorrect, then it is
silently discarded. Then it checks the cryptographic validity of
this message, i.e., it checks the MAC(s) as follows:
o If the received message is the first EAP-PSK message, there is no
MAC to check as none is included in message 1.
o If the received message is the second EAP-PSK message, the
validity of MAC_P is checked.
o If the received message is the third EAP-PSK message, the validity
of MAC_S is checked and then the validity of the Tag included in
P_CHANNEL_S_0 is checked. The validity checks must be done in
this order to avoid unnecessarily deriving TEK, MSK, and EMSK in
case MAC_S is invalid, meaning that mutual authentication has
failed. Indeed, TEK is used to verify the validity of the Tag
included in P_CHANNEL_S_0.
o If the received message is the fourth EAP-PSK message, the
validity of the Tag included in P_CHANNEL_P_1 is checked.
o If the received message is an EAP-PSK message different from the
first four ones, then validity of the Tag included in P_CHANNEL is
checked.
If a validity check fails, the message is silently discarded. There
can be a counter to track the number of silently discarded messages
Section 8.8. If there is an encrypted payload in the message (namely
in the PCHANNEL attribute), then the encrypted payload is decrypted.
Then, if the decrypted payload is syntactically incorrect, the
message is silently discarded.
Bersani & Tschofenig Experimental [Page 30]
RFC 4764 EAP-PSK January 2007
5. EAP-PSK Message Format
For the sake of simplicity, EAP-PSK uses a fixed message format.
There are four different types of EAP-PSK messages:
o The first EAP-PSK message, which is sent by the server to the
peer.
o The second EAP-PSK message, which is sent by the peer to the
server.
o The third EAP-PSK message, which is sent by the server to the
peer.
o The fourth EAP-PSK message, which is sent by the peer to the
server. This is also the type of message that the peer further
sends to the server in case of an extended authentication. This
is also essentially the type of message that the server further
sends to the peer in case of an extended authentication: the only
slight modification that occurs in this last case is the setting
of the EAP Code to 1 instead of 2 in the other cases.
For the sake of clarity, the whole EAP packet that encapsulates the
EAP-PSK message (i.e., the EAP-PSK message plus its EAP headers) is
depicted in Figures 11, 13, 14, and 18.
Bersani & Tschofenig Experimental [Page 31]
RFC 4764 EAP-PSK January 2007
5.1. EAP-PSK First Message
The first EAP-PSK message is sent by the server to the peer. It has
the format presented in Figure 11.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code=1 | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type EAP-PSK | Flags | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| RAND_S |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
: :
: ID_S :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: EAP-PSK First Message
Since IANA has allocated EAP method type 47 for EAP-PSK, Type EAP-PSK
for the first EAP-PSK message as well as any other EAP-PSK message
MUST be 47.
The first EAP-PSK message consists of:
o A 1-byte Flags field
o A 16-byte random number: RAND_S
o A variable length field that conveys the server's NAI: ID_S. The
length of this field is deduced from the EAP length field. The
length of this NAI must not exceed 966 bytes. This restriction
aims at avoiding fragmentation issues (see Section 8.11).
The Flags field has the format presented in Figure 12.
Bersani & Tschofenig Experimental [Page 32]
RFC 4764 EAP-PSK January 2007
0
0 1 2 3 4 5 6 7 8
+-+-+-+-+-+-+-+-+
| T | Reserved |
+-+-+-+-+-+-+-+-+
Figure 12: EAP-PSK Flags Field
The Flags field is comprised of two subfields:
o A 2-bit T subfield, which indicates the type of EAP-PSK message:
* T=0 for the first EAP-PSK message presented in Section 5.1.
* T=1 for the second EAP-PSK message presented in Section 5.2.
* T=2 for the third EAP-PSK message presented in Section 5.3.
* T=3 for the fourth EAP-PSK message presented in Section 5.4 and
the subsequent EAP-PSK messages that may be exchanged during
extended authentication.
o A 6-bit Reserved subfield that is set to zero on transmission and
ignored on reception.
The PCHANNEL Nonce field N (see Section 5.3) is used to distinguish
between the different EAP-PSK messages that may be exchanged during
extended authentication that all have T set to 3, i.e., the fourth
EAP-PSK message and possibly the next ones.
Bersani & Tschofenig Experimental [Page 33]
RFC 4764 EAP-PSK January 2007
5.2. EAP-PSK Second Message
The second EAP-PSK message is sent by the peer to the server. It has
the format presented in Figure 13.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code=2 | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type EAP-PSK | Flags | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| RAND_S |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| RAND_P |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+ +
| |
+ +
| MAC_P |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+ +
: ID_P :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 13: EAP-PSK Second Message
Bersani & Tschofenig Experimental [Page 34]
RFC 4764 EAP-PSK January 2007
It consists of:
o A 1-byte Flags field
o The 16-byte random number sent by the server in the first EAP-PSK
message (RAND_S) that serves as a session identifier
o A 16-byte random number: RAND_P
o A 16-byte MAC: MAC_P
o A variable length field that conveys the peer's NAI: ID_P. The
length of this field is deduced from the EAP length field. The
length of this NAI must not exceed 966 bytes. This restriction
aims at avoiding fragmentation issues (see Section 8.11).
The Flags field format is presented in Figure 12.
Bersani & Tschofenig Experimental [Page 35]
RFC 4764 EAP-PSK January 2007
5.3. EAP-PSK Third Message
The third EAP-PSK message is sent by the server to the peer. It has
the format presented in Figure 14.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code=1 | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type EAP-PSK | Flags | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| RAND_S |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| MAC_S |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+ +
: PCHANNEL :
: :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 14: EAP-PSK Third Message
It consists of:
o A 1-byte Flags field
o The 16-byte random number sent by the server in the first EAP-PSK
message (RAND_S) that is used as a session identifier
o A 16-byte MAC: MAC_S
o A variable length field that constitutes the protected channel:
PCHANNEL
Bersani & Tschofenig Experimental [Page 36]
RFC 4764 EAP-PSK January 2007
The Flags field format is presented in Figure 12.
If there is no extension, i.e., if the authentication is standard,
the PCHANNEL field consists of:
o A 4-byte Nonce N (see Section 3.3).
o A 16-byte Tag (see Section 3.3).
o A 2-bit result indication flag R.
o A 1-bit extension flag E, which is set to 0.
o A 5-bit Reserved field, which is set to zero on emission and
ignored on reception.
R, E, and Reserved are sent encrypted by the protected channel (see
Section 3.3).
If there is no extension, PCHANNEL has the format presented in
Figure 15 (where R, E, and Reserved are presented in the clear for
the sake of clarity, although in reality they are sent encrypted).
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Tag |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| R |0| Reserved|
+-+-+-+-+-+-+-+-+
Figure 15: The PCHANNEL Field with E=0
If there is an extension, i.e., if the authentication is extended,
the PCHANNEL field consists of:
o A 4-byte Nonce N (see Section 3.3).
o A 16-byte Tag (see Section 3.3).
Bersani & Tschofenig Experimental [Page 37]
RFC 4764 EAP-PSK January 2007
o A 2-bit result indication flag R.
o A 1-bit extension flag E, which is set to 1.
o A 5-bit Reserved field, which is set to zero on emission and
ignored on reception.
o A variable length EXT field.
R, E, Reserved, and EXT are sent encrypted by the protected channel
(see Section 3.3).
If there is an extension, PCHANNEL has the format presented in
Figure 16 where R, E, Reserved and EXT are presented in the clear for
the sake of clarity, although in reality they are sent encrypted).
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| Tag |
+ +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| R |1| Reserved| |
+-+-+-+-+-+-+-+-+ +
: EXT :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 16: The PCHANNEL Field with E=1
This EXT field is split in two subfields:
o The EXT_Type subfield, which indicates the type of the extension
o The EXT_Payload subfield, which consists of the payload of the
extension. The EXT_Payload length is derived from the EAP Length
field. EXT_Payload must have a bit length that is a multiple of 8
bits and must not exceed 960 bytes. The latter restriction aims
Bersani & Tschofenig Experimental [Page 38]
RFC 4764 EAP-PSK January 2007
at avoiding fragmentation issues (see Section 8.11), whereas the
former comes from the EAP length being specified in bytes.
The format of the EXT field is presented in Figure 17.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| EXT_Type | |
+-+-+-+-+-+-+-+-+ +
: EXT_Payload :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 17: The EXT Field
5.4. EAP-PSK Fourth Message
The fourth EAP-PSK message is sent by the peer to the server. It has
the format presented in Figure 18.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code=2 | Identifier | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type EAP-PSK | Flags | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
| RAND_S |
+ +
| |
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
: :
: PCHANNEL :
: :
: :
+ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 18: EAP-PSK Fourth Message
Bersani & Tschofenig Experimental [Page 39]
RFC 4764 EAP-PSK January 2007
It consists of:
o A 1-byte Flags field
o The 16-byte random number sent by the server in the first EAP-PSK
message (RAND_S) that is used as a session identifier
o A variable length field that constitutes the protected channel:
PCHANNEL
The Flags field format is presented in Figure 12.
The PCHANNEL field has the following structure, which was already
described in Section 5.3.
If there is no extension, i.e., if the authentication is standard,
the PCHANNEL field consists of:
o A 4-byte Nonce N (see Section 3.3).
o A 16-byte Tag (see Section 3.3).
o A 2-bit result indication flag R.
o A 1-bit extension flag E, which is set to 0.
o A 5-bit Reserved field, which is set to zero on emission and
ignored on reception.
R, E, and Reserved are sent encrypted by the protected channel (see
Section 3.3).
If there is no extension, PCHANNEL has the format presented in
Figure 15.
If there is an extension, i.e., if the authentication is extended,
the PCHANNEL field consists of:
o A 4-byte Nonce N (see Section 3.3).
o A 16-byte Tag (see Section 3.3).
o A 2-bit result indication flag R.
o A 1-bit extension flag E, which is set to 1.
o A 5-bit Reserved field, which is set to zero on emission and
ignored on reception.
Bersani & Tschofenig Experimental [Page 40]
RFC 4764 EAP-PSK January 2007
o A variable length EXT field.
R, E, Reserved, and EXT are sent encrypted by the protected channel
(see Section 3.3).
If there is an extension, PCHANNEL has the format presented in
Figure 16.
This EXT field is split in two subfields:
o The EXT_Type subfield, which indicates the type of the extension
o The EXT_Payload subfield, which consists of the payload of the
extension. The EXT_Payload length is derived from the EAP Length
field. EXT_Payload must have a bit length that is a multiple of 8
bits and must not exceed 960 bytes. The latter restriction aims
at avoiding fragmentation issues (see Section 8.11).
The format of the EXT field is presented in Figure 17.
6. Rules of Operation for the EAP-PSK Protected Channel
In this section, the rules of operation of the EAP-PSK protected
channel are presented:
o How protected result indications are implemented.
o How an extended authentication works in details.
6.1. Protected Result Indications
The R flag of the PCHANNEL field in the third and fourth types of
EAP-PSK messages is used to provide result indications.
Since this 2-bit flag is communicated over the protected channel, it
is:
o Encrypted so that only the peer and the server can know its value.
o Integrity-protected so that it cannot be modified by an attacker
without the peer or the server detecting this modification.
o Protected against replays.
This 2-bit R flag can take the following values:
o 01 to mean CONT
Bersani & Tschofenig Experimental [Page 41]
RFC 4764 EAP-PSK January 2007
o 10 to mean DONE_SUCCESS
o 11 to mean DONE_FAILURE
The peer and the server each remember some information about both the
values of R that they have sent and the values of R they have
received. It is the conjunction of both sent and received R values
that indicate the success or the failure of the EAP-PSK dialog.
In the case of a standard authentication, the following values of R
should be exchanged:
o Either the server sends a DONE_SUCCESS in the PCHANNEL of the
third EAP-PSK message, to which the peer replies with a
DONE_SUCCESS in the PCHANNEL of the fourth EAP-PSK message, which
successfully ends the EAP-PSK dialog.
o Or the server sends a DONE_FAILURE in the PCHANNEL of the third
EAP-PSK message, to which the peer replies with a DONE_FAILURE in
the PCHANNEL of the fourth EAP-PSK message, which unsuccessfully
ends the EAP-PSK dialog.
In the case of an extended authentication, more complex exchanges may
occur, which is why the CONT value was introduced.
The rules of operation for each value that R may take are detailed
below.
6.1.1. CONT
The server and the peer each initialize the values of R they intend
to send and receive as CONT.
Here CONT stands for "Continue". It indicates that the EAP-PSK
dialog is not yet successful and that the party sending it wants to
continue the dialog to try and reach success.
Indeed, although the peer and the server must have successfully
authenticated each other, thanks to MAC_P and MAC_S, before they
start communicating over the protected channel, the EAP-PSK dialog
may not yet be deemed successful after this mutual authentication
because of authorization issues. For instance, a prepaid customer of
a wireless Hot-Spot might have successfully authenticated but has to
refill its account, e.g., with a credit card transaction over the
protected channel, before it is authorized.
Bersani & Tschofenig Experimental [Page 42]
RFC 4764 EAP-PSK January 2007
6.1.2. DONE_SUCCESS
DONE_SUCCESS indicates that the party that sent it deems the EAP-PSK
dialog successful and therefore proposes to end this dialog.
Once the server has sent a DONE_SUCCESS, it must keep sending this
value for R.
The peer must first receive a DONE_SUCCESS from the server before it
is allowed to send a DONE_SUCCESS.
After the peer has received a DONE_SUCCESS from the server, it may:
o Send a CONT to the server if it has not reached success on its
side. The server that receives a CONT should continue the EAP-PSK
dialog (see Section 8.2 for some discussion on the security
implications of this).
o Send a DONE_SUCCESS to the server, which will end the EAP-PSK
dialog with success.
o Send a DONE_FAILURE to the server, which will end the EAP-PSK
dialog with failure.
6.1.3. DONE_FAILURE
DONE_FAILURE indicates that the party that sent it deems the EAP-PSK
dialog unsuccessful and proposes to end this dialog because nothing
will make it change its mind.
If the server is the first to send a DONE_FAILURE, then the peer that
receives this DONE_FAILURE must reply with a DONE_FAILURE and fail,
which ends the EAP-PSK dialog.
If the peer is the first to send a DONE_FAILURE, then the server that
receives this DONE_FAILURE must immediately end this EAP-PSK dialog
without sending any further EAP-PSK message, and fail.
6.2. Extended Authentication
An extended authentication can only be started by the server.
Exactly one extension (identified by the EXT_Type subfield of the EXT
field) must be run during an EAP-PSK extended authentication dialog.
The extension is run over the protected channel: it can assume
confidentiality, integrity, and replay protection.
Bersani & Tschofenig Experimental [Page 43]
RFC 4764 EAP-PSK January 2007
To start an extended authentication, the server sets the PCHANNEL E
flag to 1 and includes the EXT_Payload of the extension it has
chosen.
Since EAP-PSK does not provide fragmentation, the extension must not
send an EXT_Payload larger than 960 bytes, which corresponds to the
1020-byte EAP MTU that may minimally be assumed (see [3]).
Moreover, an extension must not send an empty EXT_Payload (because
this has a particular meaning for EAP-PSK; see below).
When the peer receives the third EAP-PSK message with the E flag set
to 1, it checks whether it is able to process the proposed extension.
If the peer is not able to process the proposed extension, i.e., it
does not recognize the EXT_Type of the proposed extension, it sets
E=1 in its reply (the fourth EAP-PSK message) and include an EXT
field of the same EXT_Type but with an empty EXT_Payload.
Depending on the values taken by the R flags, the EAP-PSK dialog may:
o End
* If the peer's policy mandates that it fails in the case of an
unrecognized extension, it sends a DONE_FAILURE in the fourth
EAP-PSK message.
* If the server has sent a DONE_SUCCESS in the third EAP-PSK
message, and the peer's policy authorizes it to succeed even if
the extension is not recognized, the peer sends a DONE_SUCCESS.
o Continue for exactly one round-trip; namely, in case the server
has sent a CONT in the third EAP-PSK message and the peer's policy
authorizes it to succeed even if the extension is not recognized,
the peer replies with a CONT in the fourth EAP-PSK message. The
server must then, depending on its policy, send either a
DONE_SUCCESS or a DONE_FAILURE to the peer in the fifth EAP-PSK
message. If the server sent a DONE_SUCCESS in the fifth EAP-PSK
message, the peer must send a DONE_SUCCESS in the sixth EAP-PSK
message. All these messages must have the E flag set to 1 with an
EXT field with the EXT_Type of the extension that was proposed and
an empty EXT_Payload (this behavior was chosen to simplify
implementations).
If the peer is able to process the proposed extension, then it does
so. In this case, the extension must be aware of the R values sent
and received and able to propose to update them. All the subsequent
messages exchanged between the peer and the server must have the E
Bersani & Tschofenig Experimental [Page 44]
RFC 4764 EAP-PSK January 2007
flag set to 1 with an EXT field of the EXT_Type of the extension that
was proposed and a non-empty EXT_Payload.
7. IANA Considerations
This section provides guidance to the IANA regarding registration of
values related to the EAP-PSK protocol, in accordance with [6].
The following terms are used here with the meanings defined in [6]:
"name space" and "registration".
The following policies are used here with the meanings defined in
[6]: "Expert Review" and "Specification Required".
This document introduces one new Internet Assigned Numbers Authority
(IANA) consideration: there is one name space in EAP-PSK that
requires registration: the EXT_Type values (see Section 5.3 and
Section 5.4).
For registration requests where a Designated Expert should be
consulted, the responsible IETF Area Director should appoint the
Designated Expert. The intention is that any allocation will be
accompanied by a published RFC. But in order to allow for the
allocation of values prior to the RFC being approved for publication,
the Designated Expert can approve allocations once it seems clear
that an RFC will be published. The Designated Expert will post a
request to the EAP WG mailing list (or a successor designated by the
Area Director) for comment and review, including an Internet-Draft.
Before a period of 30 days has passed, the Designated Expert will
either approve or deny the registration request and publish a notice
of the decision to the EAP WG mailing list or its successor, as well
as informing IANA. A denial notice must be justified by an
explanation and, in the cases where it is possible, concrete
suggestions on how the request can be modified so as to become
acceptable.
7.1. Allocation of an EAP-Request/Response Type for EAP-PSK
IANA allocated a new EAP Type for EAP-PSK.
7.2. Allocation of EXT Type Numbers
EAP-PSK is not intended as a general-purpose protocol, and
allocations of EXT_Type should not be made for purposes unrelated to
authentication, authorization, and accounting.
EXT_Type numbers have a range from 1 to 255.
Bersani & Tschofenig Experimental [Page 45]
RFC 4764 EAP-PSK January 2007
EXT_Type 255 has been allocated for Experimental use.
EXT_Type 1-254 may be allocated on the advice of a Designated Expert,
with Specification Required.
8. Security Considerations
[3] highlights several attacks that are possible against EAP, as EAP
does not provide any robust security mechanism.
This section discusses the claimed security properties of EAP-PSK as
well as vulnerabilities and security recommendations in the threat
model of [3].
8.1. Mutual Authentication
EAP-PSK provides mutual authentication.
The server believes that the peer is authentic because it can
calculate a valid MAC and the peer believes that the server is
authentic because it can calculate another valid MAC.
The authentication protocol that inspired EAP-PSK, AKEP2, enjoys a
security proof in the provable security paradigm; see [14].
The MAC algorithm used in the instantiation of AKEP2 within EAP-PSK,
CMAC, also enjoys a security proof in the provable security paradigm;
see [29]. A tag length of 16 bytes for CMAC is currently deemed
appropriate by the cryptographic community for entity authentication.
The underlying block cipher used, AES-128, is widely believed to be a
secure block cipher.
Finally, the key used for mutual authentication, AK, is only used for
that purpose, which makes this part cryptographically independent of
the other parts of the protocol.
EAP-PSK provides mutual authentication if it is based on a pairwise
PSK of sufficient strength. If the PSK is not pairwise or not
sufficiently strong, then it does not provide authentication. In
this way, EAP-PSK is no different than other authentication protocols
based on Pre-Shared Keys.
Bersani & Tschofenig Experimental [Page 46]
RFC 4764 EAP-PSK January 2007
8.2. Protected Result Indications
EAP-PSK provides protected result indications thanks to its 2-bit R
flag (see Section 6.1). This 2-bit R flag is protected because it is
encrypted and integrity protected by the EAX mode of operation; see
Section 3.3.
Care may be taken against Byzantine failures, that is to say, for
instance, when a peer tries to force a server to engage in a never-
ending conversation. This could, for example, be done by a peer that
keeps sending a CONT after it has received a DONE_SUCCESS from the
server. A policy may limit the number of rounds in an EAP-PSK
extended authentication to mitigate this threat, which is outside our
threat model.
It should also be noted that the cryptographic protection of the
result indications does not prevent message deletion.
For instance, let us consider a scenario in which:
o A server sends a DONE_SUCCESS to a peer.
o The peer replies with a DONE_SUCCESS.
In the case that the last message from the peer is intercepted, and
an EAP Success is sent to the peer before any retransmission from the
server reaches it, or the retransmissions from the server are also
deleted, the peer will believe that it has successfully authenticated
to the server while the server will fail.
This behavior is well known (see, e.g., [23]) and in a sense
unavoidable. There is a trade-off between efficiency and the "level"
of information sharing that is attainable. EAP-PSK specified a
single round-trip of DONE_SUCCESS because it is believed that:
o If there is an adversary capable of disrupting the communication
channel, it can do so whenever it wants (be it after 1 or 10
round-trips or even during data communication).
o Other layers/applications will generally start by doing a specific
key exchange and confirmation procedure using the keys derived by
EAP-PSK. This is typically done by IEEE 802.11i "four-way
handshake". In case the error is not detected by EAP-PSK, it
should be detected then (please note, however, that it is bad
practice to rely on an external mechanism to ensure
synchronization, unless this is an explicit property of the
external mechanism).
Bersani & Tschofenig Experimental [Page 47]
RFC 4764 EAP-PSK January 2007
8.3. Integrity Protection
EAP-PSK provides integrity protection thanks to the Tag of its
protected channel (see Section 3.3).
EAP-PSK provides integrity protection if it is based on a pairwise
PSK of sufficient strength. If the PSK is not pairwise or not
sufficiently strong, then it does not provide authentication. In
this way, it is no different than other authentication protocols
based on Pre-Shared Keys.
8.4. Replay Protection
EAP-PSK provides replay protection of its mutual authentication part
thanks to the use of random numbers RAND_S and RAND_P. Since RAND_S
is 128 bits long, one expects to have to record 2**64 (i.e.,
approximately 1.84*10**19) EAP-PSK successful authentications before
an authentication can be replayed. Hence, EAP-PSK provides replay
protection of its mutual authentication part as long as RAND_S and
RAND_P are chosen at random; randomness is critical for security.
EAP-PSK provides replay protection during the conversation of the
protected channel thanks to the Nonce N of its protected channel (see
Section 3.3). This nonce is initialized to 0 by the server and
monotonically incremented by one by the party that receives a valid
EAP-PSK message. For instance, after receiving from the server a
valid EAP-PSK message with Nonce set to x, the peer will answer with
an EAP-PSK message with Nonce set to x+1 and wait for an EAP-PSK
message with Nonce set to x+2. A retransmission of the server's
message with Nonce set to x would cause the peer EAP layer to resend
the message in which Nonce was set to x+1, which would be transparent
to the EAP-PSK layer.
The EAP peer must check that the Nonce is indeed initialized to 0 by
the server.
8.5. Reflection Attacks
EAP-PSK provides protection against reflection attacks in case of an
extended authentication because:
o It integrity protects the EAP header (which contains the
indication Request/Response.
o It includes two separate spaces for the Nonces: the EAP server
only receives messages with odd nonces, whereas the EAP peer only
receives messages with even nonces.
Bersani & Tschofenig Experimental [Page 48]
RFC 4764 EAP-PSK January 2007
8.6. Dictionary Attacks
Because EAP-PSK is not a password protocol, it is not vulnerable to
dictionary attacks.
Indeed, the PSK used by EAP-PSK must not be derived from a password.
Derivation of the PSK from a password may lead to dictionary attacks.
However, using a 16-byte PSK has:
o Ergonomic impacts: some people may find it cumbersome to manually
provision a 16-byte PSK.
o Deployment impacts: some people may want to reuse existing
credential databases that contain passwords and not PSKs.
Because people will probably not heed the warning not to use
passwords, guidance to derive a PSK from a password is provided in
Appendix A. The method proposed in Appendix A only tries to make
dictionary attacks harder. It does not eliminate them.
However, it does not cause a fatal error if passwords are used
instead of PSKs: people rarely use password-derived certificates, so
why should they do so for shared keys?
8.7. Key Derivation
EAP-PSK supports key derivation.
The key hierarchy is specified in Section 2.1.
The mechanism used for key derivation is the modified counter mode.
The instantiation of the modified counter in EAP-PSK complies with
the conditions stated in [5] so that the security proof for this mode
holds.
The underlying block cipher used, AES-128, is widely believed to be a
secure block cipher.
A first key derivation occurs to calculate AK and KDK from the PSK:
it is called the key setup (see Section 3.1). It uses the PSK as the
key to the modified counter mode. Thus, AK and KDK are believed to
be cryptographically separated and computable only to those who have
knowledge of the PSK.
Bersani & Tschofenig Experimental [Page 49]
RFC 4764 EAP-PSK January 2007
A second key derivation occurs to derive session keys, namely, the
TEK, MSK, and EMSK (see Section 3.2). It uses KDK as the key to the
modified counter mode.
The protocol design explicitly assumes that neither AK nor KDK are
shared beyond the two parties utilizing them. AK loses its efficacy
to mutually authenticate the peer and server with each other when it
is shared. Similarly, the derived TEK, MSK, and EMSK lose their
value when KDK is shared with a third party.
It should be emphasized that the peer has control of the session keys
derived by EAP-PSK. In particular, it can easily choose the random
number it sends in EAP-PSK so that one of the nine derived 16-byte
key blocks (see Section 2.1) takes a pre-specified value.
It was chosen not to prevent this control of the session keys by the
peer because:
o Preventing it would have added some complexity to the protocol
(typically, the inclusion of a one-way mode of operation of AES in
the key derivation part).
o It is believed that the peer won't try to force the server to use
some pre-specified value for the session keys. Such an attack is
outside the threat model and seems to have little value compared
to a peer sharing its PSK.
However, this is not the behavior recommended by EAP in Section 7.10
of [3].
Since deriving the session keys requires some cryptographic
computations, it is recommended that the session keys be derived only
once authentication has succeeded (i.e., once the server has
successfully verified MAC_P for the server side, and once the peer
has successfully verified MAC_S for the peer side).
It is recommended to take great care in implementations, so that
derived keys are not made available if the EAP-PSK dialog fails
(e.g., ends with DONE_FAILURE).
The TEK must not be made available to anyone except to the current
EAP-PSK dialog.
Bersani & Tschofenig Experimental [Page 50]
RFC 4764 EAP-PSK January 2007
8.8. Denial-of-Service Resistance
Denial of Service (DoS) resistance has not been a design goal for
EAP-PSK.
It is, however, believed that EAP-PSK does not provide any obvious
and avoidable venue for such attacks.
It is worth noting that the server has to do a cryptographic
calculation and maintain some state when it engages in an EAP-PSK
conversation, namely, generate and remember the 16-byte RAND_S.
However, this should not lead to resource exhaustion as this state
and the associated computation are fairly lightweight.
Please note that both the peer and the server must commit to their
RAND_S and RAND_P to protect their partners from flooding attacks.
It is recommended that EAP-PSK not allow EAP notifications to be
interleaved in its dialog to prevent potential DoS attacks. Indeed,
since EAP notifications are not integrity protected, they can easily
be spoofed by an attacker. Such an attacker could force a peer that
allows EAP notifications to engage in a discussion that would delay
his or her authentication or result in the peer taking unexpected
actions (e.g., in case a notification is used to prompt the peer to
do some "bad" action).
It is up to the implementation of EAP-PSK or to the peer and the
server to specify the maximum number of failed cryptographic checks
that are allowed. For instance, does the reception of a bogus MAC_P
in the second EAP-PSK message cause a fatal error or is it discarded
to continue waiting for the valid response of the valid peer? There
is a trade-off between possibly allowing multiple tentative forgeries
and allowing a direct DoS (in case the first error is fatal).
For the sake of simplicity and denial-of-service resilience, EAP-PSK
has chosen not to include any error messages. Hence, an "invalid"
EAP-PSK message is silently discarded. Although this makes
interoperability testing and debugging harder, this leads to simpler
implementations and does not open any venue for denial-of-service
attacks.
8.9. Session Independence
Thanks to its key derivation mechanisms, EAP-PSK provides session
independence: passive attacks (such as capture of the EAP
conversation) or active attacks (including compromise of the MSK or
EMSK) do not enable compromise of subsequent or prior MSKs or EMSKs.
Bersani & Tschofenig Experimental [Page 51]
RFC 4764 EAP-PSK January 2007
The assumption that RAND_P and RAND_S are random is central for the
security of EAP-PSK in general and session independence in
particular.
8.10. Exposition of the PSK
EAP-PSK does not provide Perfect Forward Secrecy. Compromise of the
PSK leads to compromise of recorded past sessions.
Compromise of the PSK enables the attacker to impersonate the peer
and the server: compromise of the PSK leads to "full" compromise of
future sessions.
EAP-PSK provides no protection against a legitimate peer sharing its
PSK with a third party. Such protection may be provided by
appropriate repositories for the PSK, whose choice is outside the
scope of this document. The PSK used by EAP-PSK must only be shared
between two parties: the peer and the server. In particular, this
PSK must not be shared by a group of peers communicating with the
same server.
The PSK used by EAP-PSK must be cryptographically separated from keys
used by other protocols, otherwise the security of EAP-PSK may be
compromised. It is a rule of thumb in cryptography to use different
keys for different applications.
8.11. Fragmentation
EAP-PSK does not support fragmentation and reassembly.
Indeed, the largest EAP-PSK frame is at most 1015 bytes long,
because:
o The maximum length for the peer NAI identity used in EAP-PSK is
966 bytes (see Section 5.2). This should not be a limitation in
practice (see Section 2.2 of [2] for more considerations on NAI
length).
o The maximum length for the EXT_Payload field used in EAP-PSK is
960 bytes (see Section 5.3 and Section 5.4).
Per Section 3.1 of [3], the lower layers over which EAP may be run
are assumed to have an EAP MTU of 1020 bytes or greater. Since the
EAP header is 5 bytes long, supporting fragmentation for EAP-PSK is
unnecessary.
Extensions that require sending a payload larger than 960 bytes
should provide their own fragmentation and reassembly mechanism.
Bersani & Tschofenig Experimental [Page 52]
RFC 4764 EAP-PSK January 2007
8.12. Channel Binding
EAP-PSK does not provide channel binding as this feature is still
very much a work in progress (see [13]).
However, it should be easy to add it to EAP-PSK as an extension (see
Section 4.2).
8.13. Fast Reconnect
EAP-PSK does not provide any fast reconnect capability.
Indeed, as noted, for instance, in [15], mutual authentication
(without counters or timestamps) requires three exchanges, thus four
exchanges in EAP since any EAP-Request must be answered to by an EAP-
Response.
Since this minimum bound is already reached in EAP-PSK standard
authentication, there is no way the number of round-trips used within
EAP-PSK can be reduced without using timestamps or counters.
Timestamps and counters were deliberately avoided for the sake of
simplicity and security (e.g., synchronization issues).
8.14. Identity Protection
Since it was chosen to restrict to a single cryptographic primitive
from symmetric cryptography, namely, the block cipher AES-128, it
appears that it is not possible to provide "reasonable" identity
protection without failing to meet the simplicity goal.
Hereafter is an informal discussion of what is meant by identity
protection and the rationale behind the requirement of identity
protection. For some complementary discussion, refer to [37].
Identity protection basically means preventing the disclosure of the
identities of the communicating parties over the network, which is
quite contradictory to authentication. There are two levels of
identity protection: protection against passive attackers and
protection against active eavesdroppers.
As explained in [37], "a common example [for identity protection] is
the case of mobile devices wishing to prevent an attacker from
correlating their (changing) location with the logical identity of
the device (or user)".
If only symmetric cryptography is used, only a weak form of identity
protection may be offered, namely, pseudonym management. In other
words, the peer and the server agree on pseudonyms that they use to
Bersani & Tschofenig Experimental [Page 53]
RFC 4764 EAP-PSK January 2007
identify each other and usually change them periodically, possibly in
a protected way so that an attacker cannot learn new pseudonyms
before they are used.
With pseudonym management, there is a trade-off between allowing for
pseudonym resynchronization (thanks to a permanent identity) and
being vulnerable to active attacks (in which the attacker forges
messages simulating a pseudonym desynchronization).
Indeed, a protocol using time-varying pseudonyms may want to
anticipate "desynchronization" situations such as, for instance, when
the peer believes that its current pseudonym is "pseudo1@bigco.com"
whereas the server believes this peer will use the pseudonym
"pseudo2@bigco.com" (which is the pseudonym the server has sent to
update "pseudo1@bigco.com").
Because pseudonym management adds complexity to the protocol and
implies this unsatisfactory trade-off, it was decided not to include
this feature in EAP-PSK.
However, EAP-PSK may trivially provide some protection when the
concern is to avoid the "real-life" identity of the user being
"discovered". For instance, let us take the example of user John Doe
that roams and connects to a Hot-Spot owned and operated by Wireless
Internet Service Provider (WISP) BAD. Suppose this user
authenticates to his home WISP (WISP GOOD) with an EAP method under
an identity (e.g., "john.doe@wispgood.com") that allows WISP BAD (or
an attacker) to recover his "real-life" identity, i.e., John Doe. An
example drawback of this is when a competitor of John Doe's WISP
wants to win John Doe as a new customer by sending him some special
targeted advertisement.
EAP-PSK can very simply thwart this attack, merely by avoiding to
provide John Doe with an NAI that allows easy recovery of his real-
life identity. It is believed that when an NAI that is not
correlated to a real-life identity is used, no valuable information
leaks because of the EAP method.
Indeed, the identity of the WISP used by a peer has to be disclosed
anyway in the realm portion of its NAI to allow AAA routing.
Moreover, the Medium Access Control Address of the peer's Network
Interface Card can generally be used to track the peer as efficiently
as a fixed NAI.
Bersani & Tschofenig Experimental [Page 54]
RFC 4764 EAP-PSK January 2007
It is worth noting that the server systematically discloses its
identity, which may allow probing attacks. This may not be a problem
as the identity of the server is not supposed to remain secret. On
the contrary, users tend to want to know to whom they will be talking
in order to choose the right network to attach to.
8.15. Protected Ciphersuite Negotiation
EAP-PSK does not allow negotiating ciphersuites. Hence, it is not
vulnerable to negotiation attacks and does not implement protected
ciphersuite negotiation.
8.16. Confidentiality
Although EAP-PSK provides confidentiality in its protected channel,
it cannot claim to do so as per Section 7.2.1 of [3]: "A method
making this claim must support identity protection".
8.17. Cryptographic Binding
Since EAP-PSK is not intended to be tunneled within another protocol
that omits peer authentication, it does not implement cryptographic
binding.
8.18. Implementation of EAP-PSK
To really provide security, not only must a protocol be well thought-
out and correctly specified, but its implementation must take special
care.
For instance, implementing cryptographic algorithms requires special
skills since cryptographic software is vulnerable not only to
classical attacks (e.g., buffer overflow or missing checks) but also
to some special cryptographic attacks (e.g., side channels attacks
like timing ones; see [36]). In particular, care must be taken to
avoid such attacks in EAX implementation; please refer to [4] for a
note on this point.
An EAP-PSK implementation should use a good source of randomness to
generate the random numbers required in the protocol. Please refer
to [20] for more information on generating random numbers for
security applications.
Handling sensitive material (namely, keying material such as the PSK,
AK, KDK, etc.) should be done in a secure way (see, for instance,
[19] for guidance on secure deletion).
Bersani & Tschofenig Experimental [Page 55]
RFC 4764 EAP-PSK January 2007
The specification of a repository for the PSK that EAP-PSK uses is
outside the scope of this document. In particular, nothing prevents
one from storing this PSK on a tamper-resistant device such as a
smart card rather than having it memorized or written down on a sheet
of paper. The choice of the PSK repository may have important
security impacts.
9. Security Claims
This section provides the security claims required by [3].
[a] Mechanism. EAP-PSK is based on symmetric cryptography (AES-128)
and uses a 16-byte Pre-Shared Key (PSK).
[b] Security claims. EAP-PSK provides:
* Mutual authentication (see Section 8.1)
* Integrity protection (see Section 8.3)
* Replay protection (see Section 8.4)
* Key derivation (see Section 8.7)
* Dictionary attack resistance (see Section 8.6)
* Session independence (see Section 8.9)
[c] Key strength. EAP-PSK provides a 16-byte effective key
strength.
[d] Description of key hierarchy. Please see Section 2.1.
[e] Indication of vulnerabilities. EAP-PSK does not provide:
* Identity protection (see Section 8.14)
* Confidentiality (see Section 8.16)
* Fast reconnect (see Section 8.13)
* Fragmentation (see Section 8.11)
* Cryptographic binding (see Section 8.17)
* Protected ciphersuite negotiation (see Section 8.15)
* Perfect Forward Secrecy (see Section 8.10)
Bersani & Tschofenig Experimental [Page 56]
RFC 4764 EAP-PSK January 2007
* Key agreement: the session key is chosen by the peer (see
Section 8.7)
* Channel binding (see Section 8.12)
10. Acknowledgments
This EAP method has been inspired by EAP-Archie and EAP-SIM. Many
thanks to their respective authors: Jesse Walker (extra thanks to
Jesse Walker for his thorough and challenging expert review of EAP-
PSK), Russ Housley, Henry Haverinen, and Joseph Salowey.
Thanks to
o Henri Gilbert for some interesting discussions on the
cryptographic parts of EAP-PSK.
o Aurelien Magniez for his valuable feedback on network aspects of
EAP-PSK, his curiosity and rigor that led to numerous
improvements, and his help in the first implementation of EAP-PSK
under Microsoft Windows and Freeradius.
o Thomas Otto for his valuable feedback on EAP-PSK and the
implementation of the first version of EAP-PSK under Xsupplicant.
o Nancy Cam-Winget for some exchanges on EAP-PSK.
o Jari Arkko and Bernard Aboba, the beloved EAP WG chairs, for the
work they stimulate.
Finally, thanks to Vir Z., who has brought a permanent and
outstanding though discreet contribution to this protocol.
11. References
11.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Aboba, B., Beadles, M., Arkko, J., and P. Eronen, "The Network
Access Identifier", RFC 4282, December 2005.
[3] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
Levkowetz, "Extensible Authentication Protocol (EAP)",
RFC 3748, June 2004.
Bersani & Tschofenig Experimental [Page 57]
RFC 4764 EAP-PSK January 2007
[4] Bellare, M., Rogaway, P., and D. Wagner, "The EAX mode of
operation", FSE 04, Springer-Verlag LNCS 3017, 2004.
[5] Gilbert, H., "The Security of One-Block-to-Many Modes of
Operation", FSE 03, Springer-Verlag LNCS 2287, 2003.
[6] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA
Considerations Section in RFCs", BCP 26, RFC 2434,
October 1998.
[7] National Institute of Standards and Technology, "Specification
for the Advanced Encryption Standard (AES)", Federal
Information Processing Standards (FIPS) 197, November 2001.
[8] National Institute of Standards and Technology, "Recommendation
for Block Cipher Modes of Operation: The CMAC Mode for
Authentication", Special Publication (SP) 800-38B, May 2005.
11.2. Informative References
[9] Aboba, B., Simon, D., Eronen, P., and H. Levkowetz,"Extensible
Authentication Protocol (EAP) Key Management Framework", Work
in Progress, October 2006.
[10] Aboba, B., Calhoun, P., Glass, S., Hiller, T., McCann, P.,
Shiino, H., Zorn, G., Dommety, G., Perkins, C., Patil, B.,
Mitton, D., Manning, S., Beadles, M., Walsh, P., Chen, X.,
Sivalingham, S., Hameed, A., Munson, M., Jacobs, S., Lim, B.,
Hirschman, B., Hsu, R., Xu, Y., Campell, E., Baba, S., and E.
Jaques, "Criteria for Evaluating AAA Protocols for work
Access", RFC 2989, November 2000.
[11] Aboba, B. and D. Simon, "PPP EAP TLS Authentication Protocol",
RFC 2716, October 1999.
[12] Arkko, J. and H. Haverinen, "Extensible Authentication Protocol
Method for 3rd Generation Authentication and Key Agreement
(EAP-AKA)", RFC 4187, January 2006.
[13] Arkko, J. and P. Eronen, "Authenticated Service Information for
the Extensible Authentication Protocol (EAP)", Work in
Progress, October 2005.
[14] Bellare, M. and P. Rogaway, "Entity Authentication and Key
Distribution", CRYPTO 93, Springer-Verlag LNCS 773, 1994.
Bersani & Tschofenig Experimental [Page 58]
RFC 4764 EAP-PSK January 2007
[15] Bellare, M., Pointcheval, D., and P. Rogaway, "Authenticated
Key Exchange Secure Against Dictionary attacks", EUROCRYPT 00,
Springer-Verlag LNCS 1807, 2000.
[16] Bersani, F., "EAP shared key methods: a tentative synthesis of
those proposed so far", Work in Progress, April 2004.
[17] Bradner, S., "The Internet Standards Process -- Revision 3",
BCP 9, RFC 2026, October 1996.
[18] Carlson, J., Aboba, B., and H. Haverinen, "EAP SRP-SHA1
Authentication Protocol", Work in Progress, July 2001.
[19] Department of Defense of the United States, "National
Industrial Security Program Operating Manual", DoD 5220-22M,
January 1995.
[20] Eastlake, D., Schiller, J., and S. Crocker, "Randomness
Requirements for Security", BCP 106, RFC 4086, June 2005.
[21] Funk, P. and S. Blake-Wilson, "EAP Tunneled TLS Authentication
Protocol (EAP-TTLS)", Work in Progress, July 2004.
[22] Haller, N., Metz, C., Nesser, P., and M. Straw, "A One-Time
Password System", RFC 2289, February 1998.
[23] Halpern, J. and Y. Moses, "Knowledge and common knowledge in a
distributed environment", Journal of the ACM 37:3, 1990.
[24] Haverinen, H. and J. Salowey, "Extensible Authentication
Protocol Method for Global System for Mobile Communications
(GSM) Subscriber Identity Modules (EAP-SIM)", RFC 4186,
January 2006.
[25] Huitema, C., Postel, J., and S. Crocker, "Not All RFCs are
Standards", RFC 1796, April 1995.
[26] Institute of Electrical and Electronics Engineers, "Local and
Metropolitan Area Networks: Port-Based Network Access Control",
IEEE Standard 802.1X, September 2001.
[27] Institute of Electrical and Electronics Engineers, "Approved
Draft Supplement to Standard for Telecommunications and
Information Exchange Between Systems-LAN/MAN Specific
Requirements - Part 11: Wireless LAN Medium Access Control
(MAC) and Physical Layer (PHY) Specifications: Specification
for Enhanced Security", IEEE 802.11i-2004, 2004.
Bersani & Tschofenig Experimental [Page 59]
RFC 4764 EAP-PSK January 2007
[28] Institute of Electrical and Electronics Engineers, "Standard
for Telecommunications and Information Exchange Between Systems
- LAN/MAN Specific Requirements - Part 11: Wireless LAN Medium
Access Control (MAC) and Physical Layer (PHY) Specifications",
IEEE Standard 802.11, 1999.
[29] Iwata, T. and K. Kurosawa, "OMAC: One-Key CBC MAC", FSE 03,
Springer-Verlag LNCS 2887, 2003.
[30] Jablon, D., "The SPEKE Password-Based Key Agreement Methods",
Work in Progress, November 2002.
[31] Josefsson, S., "The EAP SecurID(r) Mechanism", Work in
Progress, February 2002.
[32] Josefsson, S., Palekar, A., Simon, D., and G. Zorn, "Protected
EAP Protocol (PEAP) Version 2", Work in Progress, October 2004.
[33] Kaliski, B., "PKCS #5: Password-Based Cryptography
Specification Version 2.0", RFC 2898, September 2000.
[34] Kamath, V. and A. Palekar, "Microsoft EAP CHAP Extensions",
Work in Progress, April 2004.
[35] Kent, S., "IP Authentication Header", RFC 4302, December 2005
[36] Kocher, P., "Timing Attacks on Implementations of Diffie-
Hellman, RSA, DSS, and Other Systems", CRYPTO 96, Springer-
Verlag LNCS 1109, 1996.
[37] Krawczyk, H., "SIGMA: the `SIGn-and-MAc' Approach to
Authenticated Diffie-Hellman and its Use in the IKE Protocols",
CRYPTO 03, Springer-Verlag LNCS 2729, June 2003.
[38] MacNally, C., "Cisco LEAP protocol description",
September 2001, available from
<http://www.missl.cs.umd.edu/wireless/ethereal/leap.txt>.
[39] Metz, C., "OTP Extended Responses", RFC 2243, November 1997.
[40] Menezes, A., van Oorschot, P., and S. Vanstone, "Handbook of
Applied Cryptography", CRC Press , 1996.
[41] National Institute of Standards and Technology, "Password
Usage", Federal Information Processing Standards (FIPS) 112,
May 1985.
Bersani & Tschofenig Experimental [Page 60]
RFC 4764 EAP-PSK January 2007
[42] Cam-Winget, N., McGrew, D., Salowey, J., and H. Zhou, "The
Flexible Authentication via Secure Tunneling Extensible
Authentication Protocol Method (EAP-FAST)", Work in Progress,
October 2006.
[43] Schneier, B., Mudge, and D. Wagner, "Cryptanalysis of
Microsoft's PPTP Authentication Extensions (MS-CHAPv2)",
CQRE 99, Springer-Verlag LNCS 1740, October 1999.
[44] Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51,
RFC 1661, July 1994.
[45] Simpson, W., "PPP Challenge Handshake Authentication Protocol
(CHAP)", RFC 1994, August 1996.
[46] Tschofenig, H., Kroeselberg, D., Pashalidis, A., Ohba, Y., and
F. Bersani, "EAP IKEv2 Method", Work in Progress, October 2006.
[47] Walker, J. and R. Housley, "The EAP Archie Protocol", Work in
Progress, June 2003.
[48] Wi-Fi Alliance, "Wi-Fi Protected Access, version 2.0",
April 2003.
[49] Wright, J., "Weaknesses in LEAP Challenge/Response", Defcon 03,
August 2003.
[50] Eronen, P. and H. Tschofenig, "Pre-Shared Key Ciphersuites for
Transport Layer Security (TLS)", RFC 4279, December 2005.
Bersani & Tschofenig Experimental [Page 61]
RFC 4764 EAP-PSK January 2007
Appendix A. Generation of the PSK from a Password - Discouraged
It is formally discouraged to use a password to generate the PSK,
since this opens the door to exhaustive search or dictionary attacks,
two attacks that would not otherwise be possible.
EAP-PSK only provides a 16-byte key strength when a 16-byte PSK is
drawn at random from the set of all possible 16-byte strings.
However, as people will probably do this anyway, guidance is provided
hereafter to generate the PSK from a password.
For some hints on how passwords should be selected, please refer to
[41].
The technique presented herein is drawn from [33]. It is intended to
try to mitigate the risks associated with password usage in
cryptography, typically dictionary attacks.
If the binary representation of the password is strictly fewer than
16 bytes long (which by the way means that the chosen password is
probably weak because it is too short), then it is padded to 16 bytes
with zeroes as its high-order bits.
If the binary representation of the password is strictly more than 16
bytes long, then it is hashed down to exactly 16 bytes using the
Matyas-Meyer-Oseas hash (please refer to [40] for a description of
this hash. Using the notation of Figure 9.3 of [40], g is the
identity function and E is AES-128 in our construction.) with
IV=0x0123456789ABCDEFFEDCBA9876543210 (this value has been
arbitrarily selected).
We now assume that we have a 16-byte number derived from the initial
password (that can be the password itself if its binary
representation is exactly 16 bytes long). We shall call this number
P16.
Following the notations used in [33], the PSK is derived thanks to
PBKDF2 instantiated with:
o P16 as P
o The first 96 bits of the XOR of the peer and server NAIs as Salt
(zero-padded in the high-order bits if necessary).
o 5000 as c
o 16 as dkLen
Bersani & Tschofenig Experimental [Page 62]
RFC 4764 EAP-PSK January 2007
Although this gives better protection than nothing, this derivation
does not stricto sensu protect against dictionary attacks. It only
makes dictionary precomputation harder.
Authors' Addresses
Florent Bersani
France Telecom R&D
38, rue du General Leclerc
Issy-Les-Moulineaux 92794 Cedex 9
FR
EMail: bersani_florent@yahoo.fr
Hannes Tschofenig
Siemens Networks GmbH & Co KG
Otto-Hahn-Ring 6
Munich 81739
GE
EMail: Hannes.Tschofenig@siemens.com
Bersani & Tschofenig Experimental [Page 63]
RFC 4764 EAP-PSK January 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78 and at www.rfc-editor.org/copyright.html, and
except as set forth therein, the authors retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Bersani & Tschofenig Experimental [Page 64]
ERRATA
